UPS + AVR Uninterruptible Power System User’s Manual Line-Interactive Sine Wave (Standard models: SS-650/1000/1200/1500/2000/3000) 100% 80% 60% 40% 20% － － LOAD ＋ － BATTERY NORMAL BACK UP LOW BATT.
TABLE OF CONTENTS Part A. for Standard models: SS650/1000 only -------------------------- Page 3 – 4 1. INTRODUCTION 1.1 Overview 1.2 Battery replacement warning 1.3 Communication interface Part B. for standard models: SS-1200/1500/2000/3000 only --------- Page 5 – 6 1. INTRODUCTION 1.1 Overview 1.2 Battery replacement warning 1.3 DIP switches 1.4 Communication interface FOR ALL MODELS 2. MAIN FEATURES ------------------------------------------------------ Page 7 3.
FRONT PANEL FOR ALL MODELS 100% 80% 60% 40% 20% 1 3 － － LOAD ＋ － BATTERY 2 NORMAL BACK UP LOW BATT. OVER LOAD 1 LEDs of battery voltage level and load level. 2 LED of operation status. 3 Control button.
Part A. for standard models: SS-650/1000 only Rear Panel 5 4 2 NEMA Type 3 1 0 + 00－ 6 0 IEC Type 1 Fuse. 2 Inlet of city power. 3 Outlets (NEMA or IEC). 4 RS-232 Interface. 5 Phone jacks for fax machine. 6 Battery connector (enclosed upon request).
1. INTRODUCTION (for standard models: SS-650/1000 only) 1.1 Overview: The series UPS is an advanced Line-Interactive Uninterruptible Power System which produces pure sine wave power to your equipment; unlike the traditional off-line UPS, the series provide very short transference when blackouts happen, and zero transference from AC mode to battery mode or from battery mode to AC mode.
Part B. for standard models: SS-1200/1500/2000/3000 only Rear Panel 4 5 6 2 NEMA Type 3 3 1 0 7 + 00－ IEC Type 0 1 Fuse. 2 Inlet of city power. 3 Outlets (NEMA/IEC). 4 RS-232 Interface. 5 DIP switches 6 Phone jacks for fax machine (optional by DIP switch). 7 Battery connector (enclosed upon request).
1. INTRODUCTION (for standard models: SS-1200/1500/2000/3000 only) 1.1 Overview: The series UPS is an advanced Line-Interactive Uninterruptible Power System which produces pure sine wave power to your equipment; unlike the traditional off-line UPS, the series provide very short transference when blackouts happen, and zero transference from AC mode to battery mode or from battery mode to AC mode.
FOR ALL MODELS 2. MAIN FEATURE: Line-Interactive structure. Microprocessor based design. ‘Green Power’ design with auto on/off function. RS-232 interface for communication. Protection for overload, short circuit, & over heat. Pure sine wave output. Zero Transference. 3. CAUTION: The UPS is designed to power computer loads and the associated peripheral devices, such as monitors, modems, external H-Disk drivers, etc.
4. INSTALLATION & OPERATION: 4.1 Installation Inspecting the packing carton for damage that may have occurred while in transit. Immediately notify the carrier and place of purchase if any damage is found. Retain the package for future use. Plugging the power cord to a 3-wire grounding receptacle. If an extension cord must be used between the UPS and the nearest wall outlet, use a 3-wire grounding type rated for at least 20 Amps. Connecting your equipment to the UPS.
5. INDICATION AND CONTROL 5.1 Battery level and load level LEDs The battery level LEDs show the voltage level both in back-up mode and in normal mode. When the LED indicates 20% of the capacity in back-up mode, it means that the UPS is going to shut down; for the length of backup time left, it will depend on the load. While when all five LEDs light in normal mode, it means that the battery is fully charged. The load level LEDs show the percentage of added load by the UPS rated capacity.
5.5 DIP Switch Setting (Available for standard models: SS-1200/1500/2000/3000) DIP Switch 1 2 3 4 Function Table of DIP Switch 1 2 Switch No. Function Voltage = 100V / 200V Voltage = 110V / 220V Voltage = 115V / 230V Voltage = 120V / 240V Up Down V V V Up V V 3 Down 4 Up Down 50Hz 60Hz Up Down Yes No V V V Frequency for DC Start Green Power (Enable/Disable) P.S.: Program setting active only after the UPS is re-started. 5.
6. COMMUNICATION INTERFACE: The UPS is able to provide two types of computer interfaces, smart software (RS-232) and dry contact (DB-9); by using different software & cable, the UPS shows different monitoring function. 6.1 The definition and setup for RS-232 is as following: Baud Rate : 2400 dps Data Length : 8 bits Stop Bit : 1 bit Parity : None 5 4 3 2 1 9 8 7 6 6.2 Pin #6 : RS-232 data Tx out.
7. TROUBLE SHOOTING Problem UPS no reaction while AC is connected Possible Cause 1. Line cord plug is loose 2. Fuse on rear panel blown (Inside the drawer of inlet) 3. Dead wall socket Action to Take 1. Check the line cord plug 2. Replace fuse 3. Check wall socket with a table lamp. Power output is normal, UPS emits continuous beep, status LED shows RED. UPS is over loaded Turn off UPS and unplug excessive loads from UPS. UPS emits continuous beep, status LED show RED, & no power on outlets.
8. SPECIFICATIONS: Part A. specifications for standard models: SS-650/1000: CAPACITY INPUT SS-650 SS-1000 650VA/390W 1000VA/600W Voltage Selectable 100/110/115/120V 1ø or 200/220/230/240V 1ø Frequency 50Hz/60Hz Auto detect Current (110V/220V) OUTPUT Voltage 6.5A / 3.25A 10A / 5A 100/110/115/120V 1ø or 200/220/230/240V 1ø ¢3% for Back-up Mode ¢10% for AVR Frequency Wave Form Current (110V/220V) TRANSFER TIME BATTERY Voltage/Capacity Level Ind.
Part B. specifications for standard models: SS-1200/1500/2000/3000: CAPACITY SS-1200 SS-1500 SS-2000 SS-3000 1200VA/720W 1500VA/900W 2000VA/1200W 3000VA/1800W INPUT Voltage Selectable 100/110/115/120V 1ø or 200/220/230/240V 1ø Frequency 50Hz/60Hz Auto detect Current (110V/220V) 12A / 6.3A 16A / 8A 20A / 10A 30A / 15A OUTPUT Voltage 100/110/115/120V 1ø or 200/220/230/240V 1ø 3% for Back-up Mode 10% for AVR Frequency 50Hz or 60Hz ± 0.
9. IMPORTANT SAFETY INSTRUCTIONS ϳ ϳ ϳ ϳ ϳ ϳ ϳ ϳ ϳ ϳ ϳ ϳ ϳ ϳ ϳ When replacing the batteries, use the same number and the same type of batteries. Do not dispose of batteries in a fire; the battery may explode. Do not open or mutilate the battery or batteries, released electrolyte is harmful to the skin and eyes. A battery can present a risk of electric shock and high short circuit current. The following precaution should be observed when working on batteries. * Remove watches, rings or other metal objects.
