Hardened PoE Ethernet Switch Signamax™ Connectivity Systems Hardened Ethernet Switch Model -065-7408PTB 065-7408P1FXSTTB 065-7408P1FXSCTB 065-7408P1FXSMTB U S E R ’ G S 1 U I D E
Hardened PoE Ethernet Switch Quick Start Guide This quick start guide describes how to install and use the Hardened PoE Ethernet Switch. This is the switch of choice for harsh environments constrained by space.
Hardened PoE Ethernet Switch FAULT *Relay warning signal disable for following: The relay contact closes if Power1 and Power2 are both failed but Power3 on. The relay contact closes if Power3 is failed but Power1 and Power2 are both on. DC Terminal Block Power Inputs: There are two pairs of power inputs can be used to power up this switch. Redundant power supplies function is supported. The 10/100BaseT/TX and 100BaseFX Connectors 1.
Hardened PoE Ethernet Switch (receive) port of device I to the Tx (transmit) port of device II. 3. The WDM 100BaseFX Connections The fiber port pinouts: Only one single-mode optical fiber is required to transmit and receive data.
Hardened PoE Ethernet Switch LED State Indication 10/100BaseT/TX, 100BaseFX Link/ACT (Green) Steady A valid network connection established. Flashing Transmitting or receiving data. ACT stands for ACTIVITY.
Hardened PoE Ethernet Switch Functional Description • Meets IEC61000-6-2 EMC Generic Standard Immunity for industrial environment. • Supports IEEE802.3af Power over Ethernet (PoE) Power Sourcing Equipment (PSE). • Supports IEEE802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps, Full/Half-duplex, Auto-Negotiation, Auto MDI/MDIX. • 100Base-FX: Multi/Single mode SC or ST type, WDM Single mode SC type. • Supports 1024 MAC addresses. Provides 1M bits buffer memory.
Hardened PoE Ethernet Switch 7
Hardened PoE Ethernet Switch Preface A member of the growing Signamax family of rugged switches, this Hardened PoE Ethernet Switch addresses a need for a smaller switch. This switch provides an affordable solution for rugged and outdoor environment, transportation road-side cabinet, industrial floor shop, multitenant dwellings or Fiber To The Home (FTTH) applications. Capable of operating at temperature extremes of -40°C to +75°C, this is the switch of choice for harsh environments constrained by space.
Hardened PoE Ethernet Switch Table of Contents QUICK START GUIDE ................................................................ 2 PHYSICAL DESCRIPTION .............................................................. 2 The Terminal Block and Power inputs.............................. 2 The 10/100BaseT/TX and 100BaseFX Connectors ...... 3 The Port Status LEDs ......................................................... 4 FUNCTIONAL DESCRIPTION .........................................................
Hardened PoE Ethernet Switch Product Overview Hardened PoE Ethernet Switch Package Contents When you unpack the product package, you shall find the items listed below. Please inspect the contents, and report any apparent damage or missing items immediately to your authorized reseller.
Hardened PoE Ethernet Switch Product Highlights Basic Features • Meets NEMA TS1 & TS2 Environmental requirements such as temperature, shock, and vibration for traffic control equipment. • Meets IEC61000-6-2 EMC Generic Standard Immunity for industrial environment. • Supports IEEE802.3af Power over Ethernet (PoE) Power Sourcing Equipment (PSE). • Support 802.3/802.3u/802.3X. • Auto-negotiation: 10/100Mbps, Full/Half-duplex; Auto MDI/MDIX. • Support 1024 MAC addresses. • Provides 1M bits memory buffer.
Hardened PoE Ethernet Switch Front Panel Display Status LEDs LED State Indication Steady Switch is properly connected to power and turned on. Off Switch is not connected to power and is turned off. POWER Power 1 Power 2 Power 3 (Green) 10/100TX or 100FX Link/ACT (Green) Steady A valid network connection established. Flashing Transmitting or receiving data. ACT stands for ACTIVITY.
Hardened PoE Ethernet Switch Physical Ports This switch provides: • Eight 10/100BaseT/TX ports • Seven 10/100BaseT/TX ports + one 100BaseFX port • Six 10/100BaseT/TX ports + two 100BaseFX ports CONNECTIVITY • RJ-45 connectors • SC or ST connector on 100BaseFX fiber port.
Hardened PoE Ethernet Switch Installation This chapter gives step-by-step instructions about how to install the switch: Selecting a Site for the Switch As with any electric device, you should place the switch where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements: - The ambient temperature should be between -40 to 75 degrees Celsius.
Hardened PoE Ethernet Switch DIN Rail Mounting Fix the DIN rail attachment plate to the back panel of the switch. Installation: Place the switch on the DIN rail from above using the slot. Push the front of the switch toward the mounting surface until it audibly snaps into place. Removal: Pull out the lower edge and then remove the switch from the DIN rail.
Hardened PoE Ethernet Switch Connecting to Power Redundant DC Terminal Block Power Inputs. Redundant DC Terminal Block Power Inputs There are two pairs of power inputs can be used to power up this device. You only need to have one power input connected to run the switch. Step 1: Connect the DC power cord to the plug-able terminal block on the switch, and then plug it into a standard DC outlet. Step 2: Disconnect the power cord if you want to shut down the switch.
Hardened PoE Ethernet Switch Alarms for Power and Port Link Failure Step 1: There are two pins on the terminal block are used for power failure detection. It provides the normally closed output when the power source is active. Use this as a dry contact application to send a signal for power failure detection.
Hardened PoE Ethernet Switch Connecting to Your Network Cable Type & Length It is necessary to follow the cable specifications below when connecting the switch to your network. Use appropriate cables that meet your speed and cabling requirements. Cable Specifications Speed Connector Port Speed Half/Full Duplex Cable Max. Distance 2-pair UTP/STP Cat. 3, 4, 5 2-pair UTP/STP Cat. 5 MMF (50 or 62.
Hardened PoE Ethernet Switch Cabling Step 1: First, ensure the power of the switch and end devices is turned off. Always ensure that the power is off before any installation. Step 2: Prepare cable with corresponding connectors for each type of port in use. Step 3: Consult the previous section for cabling requirements based on connectors and speed. Step 4: Connect one end of the cable to the switch and the other end to a desired device.
Hardened PoE Ethernet Switch Specifications Hardened PoE Ethernet Switch Applicable Standards 10/100BaseT/TX auto-negotiating ports with RJ-45 connectors, 100BaseFX fiber ports IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX/FX Switching Method Forwarding Rate 10BaseT: 100BaseTX/FX: Performance Store-and-Forward Cable 10BaseT: 100BaseTX: 100BaseFX: LED Indicators Dimensions Net Weight Power Operating Voltage & Max.
Hardened PoE Ethernet Switch EMS EN61000-6-2: EN61000-4-2 (ESD Standard) EN61000-4-3 (Radiated FRI Standards) EN61000-4-4 (Burst Standards) EN61000-4-5 (Surge Standards) EN61000-4-6 (Induced RFI Standards) EN61000-4-8 (Magnetic Field Standards) EN61000-4-11 (Voltage Dips Standards) Environmental Test Compliance IEC60068-2-6 Fc (Vibration Resistance) IEC60068-2-27 Ea (Shock) IEC60068-2-32 Ed (Free Fall) NEMA TS1/2 Environmental requirements for traffic control equipment 21
Hardened PoE Ethernet Switch Contact Information SIGNAMAX™ CONNECTIVITY SYSTEMS An AESP Company 1810 N.E. 144th Street. North Miami, Florida 33181, U.S.A. Phone: 305-944-7710 Fax: 305-652-8489 Sales: 800-446-2377 Tech. Support: 800-446-2377, ext. 201 Http://www.signamax.com E-mail: info@signamax.
