6 Port Nway Fast Ethernet Web Smart Switch Model: 065-7532 User‘s Guide
FCC Warning This device has been tested and found to comply with limits for a Class B digital device, pursuant to Part 2 and 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Introduction 065-7532 switch provides 16 10/100M ports. 065-7532 switch was designed for easy installation and high performance in an environment where traffic is on the network and the number of users increases continuously. The compact rigid desktop size was specifically designed for small to medium workgroups. 065-7532 switch can be installed where space is limited; moreover, it provides smooth network migration and easy upgrade to network capacity. SIGNAMAX LLC • www.signamax.
Package Contents Before you start to install this switch, please verify your package that contains the following items: One 065-7532 Fast Ethernet Switch One Power Cord One CD with User’s Manual Note: If any of these items is found missing or damaged, please contact your local supplier for replacement. SIGNAMAX LLC • www.signamax.
Key Features 16 Port 10/100M Nway (Auto-negotiation) Switch 11” Desktop size with metal case Can be installed in a 19” cabinet by rack-mount kits Auto-learn of networking configurations Auto-detect full/half-duplex modes for any port Dedicated full-duplex 200Mbps bandwidth Store-and-Forward switching methods IEEE 802.
Connections Switch/Hub to 065-7532 Fast Ethernet Switch 065-7532 switch provides automatic crossover detection functionality for any port. It is simple and friendly to up-link to another switch without crossover cable. PC/Other devices to 065-7532 Fast Ethernet Switch Via a twisted pair cable straight through, 065-7532 switch can be connected to PCs, servers and other network devices. SIGNAMAX LLC • www.signamax.
Rear Panel (Power) AC input AC input (100~240V/AC, 50~60Hz) UL Safety Technical Specifications Standards Features Filtering/ Forwarding Rates Transmission Media LED Indicators Power Requirement Power Consumption Dimensions Weight IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX IEEE 802.3x Flow control Number of Ports: 16 MAC Address: 4K Buffer Memory: 1.5 Mb Method: Store and Forward 100Mbps port – 148,800pps 10Mbps – 14,880pps 10BaseT Cat. 3, 4, 5 UTP/STP 100BaseTX Cat.
Operating Temperature Storage Temperature Humidity Certifications 0 to 55℃ -20 to 90℃ 10 to 90% RH (non-condensing) FCC Class B, CE Web Smart Switch Configure Please follow the steps to configure this Web Smart switch. Step 1: Use a twisted pair cable to connect this switch to your PC. Step 2: Set your PC’s IP to 192.168.2.xx. SIGNAMAX LLC • www.signamax.
Step 3: Open the web browser (like IE…), and go to 192.168.2.1 site, and then you will see the login screen. Key in the user ID and the password to pass the authentication, IP: 192.168.2.1 ID: admin Password: admin After the authentication procedure, the home page shows up. SIGNAMAX LLC • www.signamax.
Step 4: On the following home page, select the configuration by clicking the icon. It includes, - Administrator - Port Management - VLAN Setting - QoS Setting - Port Security - Logout SIGNAMAX LLC • www.signamax.
Administrator: Authentication Configuration You can change the user name and the password, and click “Update” to confirm the new change. After that, you can reset this switch by power off and then power on to take the new user name and the password effectively. SIGNAMAX LLC • www.signamax.
Administrator: System IP Configuration You can change the IP address by typing the new IP address and click “Update” to confirm the new change, and then the message will show “Setting Process OK!!”, After that, you should reset this switch by power off and then power on it to complete the new change. SIGNAMAX LLC • www.signamax.
Administrator: System Status It shows this switch MAC address, and you can select “Back to the last display” or “Logout” when the time’s out. SIGNAMAX LLC • www.signamax.
Administrator: Load Default Setting to EEPROM You can click “Load” to load the new factory default setting, and then reset the switch by power off and then power on to take it effectively. Administrator: Firmware Update SIGNAMAX LLC • www.signamax.
Follow the instruction on the screen to update the new firmware. Please contact with your sales agents to get the latest firmware information. Port Management: Port Control Configuration Select the “Port No.” which you want to configure the mode below, “Capability” - Auto-Nego. or force on 100M or 10M mode “Duplex” - you can select the port is full/half-duplex or enable/disable this port. SIGNAMAX LLC • www.signamax.
Port Management: Port Mirroring Port mirroring is used to mirror traffic from the source port to a destination port for analysis. Select the destination port from port 1 to port 16, and select the source port by click the checking box of the port. SIGNAMAX LLC • www.signamax.
Port Management: Bandwidth Control Select the “Port No.” which you want to configure the mode below, “TX Rate” is meant you can set the maximum transmission rate of this selected port and choose the full speed or in 128K/256K/512K/1M/2M/4M/8M speed. “RX Rate” is meant you can set the maximum receiving rate of this selected port and choose full speed or in 128K/256K/512K/1M/2M/4M/8M speed. SIGNAMAX LLC • www.signamax.
Port Management: Broadcast Storm Control You can enable or disable the broadcast storm protection feature by clicking “Update”. VLAN Setting: Group VLAN Setting SIGNAMAX LLC • www.signamax.
There are 8 VLAN groups, 01, 02, 03, 04, 05, 06, 07, 08 can be used. You can select a group, and then click the port number which you want to put it into the selected VLAN group. VLAN Setting: Multi to 1 Setting This is a special design for easily setting the switch VLAN into “VLAN Per Port“. After this setting, all ports can only connect to the destination port. SIGNAMAX LLC • www.signamax.
Trunk Setting: Trunk Configuration Set up port trunk groups, and click the port number you want to include it into the same group. There are two groups to choose, and the maximum of ports for one group is 4. QoS Setting: Priority Mode SIGNAMAX LLC • www.signamax.
Click the priority mode you want, there are three priority modes to choose. QoS Setting: Class of Service Configuration You can select the class of service for each port. MAC Address Configuration: MAC Address Configuration SIGNAMAX LLC • www.signamax.
Select the port number which you want to enable/disable the MAC address. For the filtering function of the port, please click ”Update” to take the setting effectively. Logout: You can click “Logout” to logout. SIGNAMAX LLC • www.signamax.
