Installation Sheet

ManualsBrandsSignature Hardware ManualsBathroom FaucetsSignature Hardware Victorian 1.2 GPM Widespread Bathroom Faucet - Drain Assembly Included

1Victorian Widespread Faucet Installation Instructions

INSTALLATION

1. Ensure that the water supply below your sink is

completely shut oﬀ by turning the valve all the way to

the right.

Tip: Place a small bucket below your workspace to

catch any water that may drip during the installation

process.

2. Remove the T-connector, lock nut, and metal

washer from the spout’s threaded shank.

VICTORIAN WIDESPREAD FAUCET

GETTING STARTED

TOOLS AND MATERIALS:

BEFORE YOU BEGIN

We recommend consulting a professional if you are

unfamiliar with installing plumbing ﬁxtures. Signature

Hardware accepts no liability for any damage to the

faucet, plumbing, sink, counter top, or personal injury

during installation.

Observe all local plumbing and building codes.

Unpack and inspect the item for damage. If any damage is

found, contact our

Customer Relations team at 1-866-855-2284.

*not included

Ensure that you have gathered all of the required

materials that are needed for the installation.

For these instructions, it is assumed that the old faucet

has been completely removed and any necessary

repairs or modiﬁcations to the water supply have been

completed.

Plumber’s Tape

Basin Wrench*

Thread Sealant*

Adjustable

Wrench*

Phillips

Screwdriver*

Small

Bucket*

OFF

Summary of content (8 pages)

PAGE 1
VICTORIAN WIDESPREAD FAUCET BEFORE YOU BEGIN INSTALLATION We recommend consulting a professional if you are unfamiliar with installing plumbing ﬁxtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or personal injury during installation. 1. Ensure that the water supply below your sink is completely shut oﬀ by turning the valve all the way to the right. Observe all local plumbing and building codes. Unpack and inspect the item for damage.
PAGE 2
VICTORIAN WIDESPREAD FAUCET 3. Set the spout into the center faucet hole. Position the decorative escutcheon so that the hole for the drain’s lift rod is in the back. 4. From beneath the countertop, slide the metal washer back onto the threaded shank. Hand tighten the lock nut, then ﬁnish tightening using an adjustable wrench. 5. Reattach the T-connector to the end of the threaded shank by hand tightening. Apply plumber’s tape or thread sealant to the threads before tightening.
PAGE 3
VICTORIAN WIDESPREAD FAUCET 7. From under the countertop, insert the valve stem into the right-side faucet hole. From above the counter top, slide one of two decorative escuthceons onto the stem. Then, attach one of the two bell ﬂanges to the stem by hand tightening until secure. 8. From beneath the sink, position the stem so that the outlet on the side of the stem is pointing inward, towards the T-connector. While holding in place, hand tighten the lock not. Finish tightening using a basin wrench. 9.
PAGE 4
VICTORIAN WIDESPREAD FAUCET 11. Attach the main water lines to the proper inlet on the bottom of each valve stem. Use an adjustable wrench to tighten, but be careful not to overtighten. Apply thread sealant or plumber’s tape to each threaded connection. Ensure that you are connecting the hot and cold lines appropriately. 13. Once installation is complete, turn the main water supply back on from below your sink. Check for any leaks underneath. ON 12.
PAGE 5
LIFT ROD SINK DRAIN INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom ﬁxtures and plumbing. Signature Hardware accepts no liability for any damage to the ﬂoor, walls, plumbing, or personal injury during installation. Unpack and inspect the item for damage. If any damage is found, contact our Customer Relations team at 1-866-855-2284.
PAGE 6
LIFT ROD SINK DRAIN INSTALLATION INSTALLATION 1. Remove the ﬂange by unthreading it from the drain body. Remove the ﬂat rubber gasket as well. 2. Set the ﬂat rubber gasket over the drain hole in your sink, then insert the ﬂange into the drain hole. 3. From beneath the sink, reattach the ﬂange by threading it back onto the drain body. 4. Connect the drain lever by threading it into the hole on the side of the drain body. The lever must pass through the hole in the stopper tailpiece to function properly.
PAGE 7
LIFT ROD SINK DRAIN INSTALLATION 5. Position the drain so that the lever is facing the back of the ﬁxture, in line with the faucet’s lift rod. While holding in place, hand tighten the lock nut until secure then ﬁnish tightening with a basin wrench. Be careful not to overtighten, which can crack a fragile sink. 6. If not already installed, insert the faucet’s lift rod into its designated hole on the back of the faucet. 7. Use the link to attach the faucet’s lift rod to the drain lever.
PAGE 8
LIFT ROD SINK DRAIN INSTALLATION 8. Attach the lift rod to the top of the link and secure it by tightening the thumb screw. 9. Make any ﬁnal adjustments to the positioning of the link and drain lever as needed. Adjust until the drain fully opens and closes. OPEN CLOSED 10. Fill your sink to check for any leaks and to ensure that the drain is functioning properly.