Installation Sheet

ManualsBrandsSignature Hardware ManualsShower FaucetsSignature Hardware Arin Thermostatic Shower System with Hand Shower and 6 Body Sprays - Rough In Included

1Arin Thermostatic Shower System with Hand Shower & 6 Body Sprays Installation Instructions

INSTRUCTIONS

TOOLS AND MATERIALS:

BEFORE INSTALLING ROUGH-IN INFORMATION

ARIN THERMOSTATIC SHOWER SYSTEM

WITH HAND SHOWER & 6 BODY SPRAYS

Pencil

Level

Screwdriver

Drill

Safety Glasses

Wrench

2.5 & 7 mm

Hex Wrench

Teﬂon

Tape

Read entire shower system installation

instructions. Observe all local building and

safety codes.

For the following installation instructions for

your new shower panel it is assumed that the

water supply lines are in place behind the

ﬁnished wall and are directly accessible for

shower installation.

Unpack and inspect shower system for any

shipping damages. If you ﬁnd any damages, do

not install. Contact Customer Service at

1-866-855-2284. If you need assistance while

installing your shower system, call our

Customer Service number.

We recommend consulting a professional if you

are unfamiliar with installing bathroom ﬁxtures

and plumbing. Signature Hardware accepts no

liability for any damages to the ﬂoor, walls,

plumbing or personal injury during installation.

Finished

Floor

7-7/8"

1-3/4" - 2-1/8"

45-1/4"

55-1/8"

82-3/4"

17-3/4"

25-5/8"

19-5/8"

13-3/4"

Summary of content (13 pages)

PAGE 1
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS BEFORE INSTALLING Read entire shower system installation instructions. Observe all local building and safety codes. ROUGH-IN INFORMATION 17-3/4" For the following installation instructions for your new shower panel it is assumed that the water supply lines are in place behind the ﬁnished wall and are directly accessible for shower installation. INSTRUCTIONS Unpack and inspect shower system for any shipping damages.
PAGE 2
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS OUT DIVERTER BACK OUT OUT IN OUT VALVE BACK HOT WATER IN COLD WATER IN OUT Arin Thermostatic Shower System with Hand Shower & 6 Body Sprays Installation Instructions 2
PAGE 3
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS INSTALLATION 1. Wrap Teﬂon tape around the threads of the 90° pipe connector and straight connector, then screw them into shower housing. Make sure the holes of the pipes are facing downward. 3. Drill pilot holes in the locations marked in the previous step. Insert anchors into the holes and lightly ﬁx the shower housing to the wall with self-tapping screws.
PAGE 4
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS 5. Place the protective cap on the shower housing. Hold the u-shaped bracket in place over the support tube and mark the location of the mounting holes. 7. Wrap Teﬂon tape around the threads on the elbows and screw them into the thermostatic valve. Connect the thermostatic and diverter valves with the connector tube.
PAGE 5
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS 9. Drill pilot holes in the locations marked in the previous step. Insert anchors and attach the valve to the wall with self-tapping screws. Ø5/16" Hole 47-1/4" ~ 59" Anchor Self-tapping Screw 11. Connect the water inlet and outlet tubes (hot water is always on the left, and cold water is always on the right). Plug the outlet. Phillips Screwdriver 17-3/4" 13-3/4" Plug 55-1/8" 10.
PAGE 6
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS 12. Remove the protective cap. Turn on the water supply to test the water pressure and connections. Replace the protective cap when ﬁnished. Close diverter valve. 13. Apply tile or other material to ﬁnish the shower surround. Leave space around the plugs on the sides of valve for any future maintenance needs. Change the grades of the diverter valve.
PAGE 7
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS 14. Remove the protective caps and plugs. Plug 15. Wrap Teﬂon tape around the threaded portion of the connector tubes and screw them into shower housing. Filter Connective Tube Hex Wrench 16. Attach the shower arm and escutcheon. M3 Screw Shower Arm Escutcheon S2.
PAGE 8
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS 17. Remove the protective cap from the shower arm, and connect the shower arm and shower head. 19. Attach the shower arm to the connector tubes and press the escutcheon into the wall. Protective Cap Shower Head M5 screws Shower 18. Remove the plug and secure the shower head and the arm with the M5 screw. Replace the plug when ﬁnished. 20. Tighten the M5 screws with the 2.5mm hex wrench.
PAGE 9
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS 21. Remove fastening screw and lengthen valve rod by Phillips screwdriver. 23. Wrap Teﬂon tape around the threaded portion of the side spray joint and screw it into the wall. Lengthening Valve Rod Fastening Screw Side Spray 22. Assemble the valve trim kits for valve and both diverters according to the diagram. Diverter Escutcheon Plastic Space Collar 24.
PAGE 10
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS 25. Run water to check for leaks. Turn upper diverter to the left. This will allow water to ﬂow from hand shower. 26. Next, turn the lower diverter to the left. This will allow water to ﬂow from the body sprays.
PAGE 11
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS 27. Turn the upper diverter to the starting position. This will stop the ﬂow of water from the hand shower. 28. Now turn the upper diverter to the right. This will allow water to ﬂow from the rainfall shower head.
PAGE 12
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS 29. Turn the lower diverter to its starting position. This will stop the ﬂow of water to the body sprays. 30. Next, turn the upper diverter to the down position. This will allow the water to ﬂow from the waterfall outlet on the shower head.
PAGE 13
ARIN THERMOSTATIC SHOWER SYSTEM WITH HAND SHOWER & 6 BODY SPRAYS MAINTENANCE 31. Now turn lower diverter to the left. This will allow water to ﬂow from the body sprays. Finally, turn all diverters to their starting positions to stop the ﬂow of water. If you are experiencing low ﬂow rate or the temperature control is imprecise, it is often due to poor water which blocks the ﬁlter nets on both sides of valve body and the ﬁlter net on the thermostatic cartridge. To clean the ﬁlter net, turn oﬀ the main valve.