Air Kit Installation

ManualsBrandsSignature Hardware ManualsShop All Signature HardwareSignature Hardware Kepler 67" Acrylic Freestanding Air Tub

1Air Massage Kit Installation Instructions

AIR MASSAGE KIT INSTALLATION INSTRUCTIONS

GETTING STARTED

TOOLS AND MATERIALS:

BEFORE YOU BEGIN

We recommend consulting a professional if you are

unfamiliar with installing bathroom ﬁxtures and

plumbing. Signature Hardware accepts no liability for

any damage to the ﬂoor, walls, plumbing, or personal

injury during installation.

Observe all local plumbing and building codes.

Unpack and inspect all items for damage. If any damage

is found, contact our Customer Relations team at

1-866-855-2284.

*not included

Ensure that you have gathered all of the required

materials that are needed for the installation.

Keep the air kit components easily accessible for any

future mainetenance that may be necessary.

STEP 1:

ELECTRICAL REQUIREMENTS

1. Before beginning electrical installation make sure

that the electricity is disconnected at the fuse box.

2. Wiring should be permanent. Do not use an

extension cord. Have the electrical part of the

installation done by, or approved by, a qualiﬁed

electrician.

3. Determine a location to mount your blower motor.

The blower should be mounted within 5’ of the tub in an

uninsulated location, and easily accessible. There

should be suﬃcient air space around the motor for

proper functionality. If you are mounting the blower

behind a wall or below the ﬂoor, you must have an

access panel of approximately 30”x15” to allow access

for servicing.

4. Use the factory pre-installed type SJ wire to connect

to junction box. Run a separate 120V, 60Hz, 15A G.F.I.

(Class A protected) electric circuit from the main fuse

box to the junction box. Use a 14 gauge three

conductor cable (2 wires plus ground) in connections up

to 100 feet (30, 4m) from the main fuse box. Refer to

your local electrical code if the distance between the

tub and the main fuse box is more than 100 feet.

5. Use the following wiring diagram as a guideline when

preparing the electrical components.

Tape Measure*Marker*

Drill*

Screwdriver*

MAIN FUSE BOX

WHITE

BLACK

GREEN

120V, 60Hz, 15A

GROUND FAULT

CIRCUIT INTERUPTER

Class A

JUNCTION

BOX

MAIN BLOWER

Summary of content (7 pages)

PAGE 1
AIR MASSAGE KIT INSTALLATION INSTRUCTIONS STEP 1: ELECTRICAL REQUIREMENTS BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom ﬁxtures and plumbing. Signature Hardware accepts no liability for any damage to the ﬂoor, walls, plumbing, or personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect all items for damage. If any damage is found, contact our Customer Relations team at 1-866-855-2284.
PAGE 2
AIR MASSAGE KIT INSTALLATION INSTRUCTIONS STEP 2: INSTALLING THE AIR MASSAGE KIT The illustration below may be useful as a reference during installation. Installation shown is typical. Security Device MANI-SD-A 1-1/4” Adapter Wall To 120V 15 AMP Dedicated GFI 3’ Air Hose 2” Tub Rim 1-1/4” Adapter Manifold under tub MAN-A-4-AC Remote Control Receiver Module Check Vave 1-1/4” Adapter Floor Silver SLS+ Variable Speed Blower 9’ Air Hose Blower Dimensions L: 12.
PAGE 3
AIR MASSAGE KIT INSTALLATION INSTRUCTIONS 1. Remove your tub from its packaging. Carefully turn the tub upside down or on its side, and lay it on a sheet of cardboard, or a soft surface, to prevent scratching. The air system’s jets, tubing, and manifold should be pre-installed into your tub. Check all pre-installed connections to ensure that nothing came loose or dislodged during shipping. 3. Plug the remote-control receiver module into the designated location on the side of the blower motor.
PAGE 4
AIR MASSAGE KIT INSTALLATION INSTRUCTIONS 5. Connect one end of the 9’ air hose to the second end of the security device. Use a provided hose clamp to secure. Connect the opposite end of the hose to the manifold underneath the tub, using another hose clamp to secure. 7. Plug the blower motor into its dedicated electrical receptacle. Proceed to Step 3 of installation to program your remote control.
PAGE 5
AIR MASSAGE KIT INSTALLATION INSTRUCTIONS STEP 3: REMOTE CONTROL MOUNTING AND PROGRAMMING 1. Determine a location to mount your remote control on your tub. 3. Position the magnets on the exterior of the bathtub, on the opposite side of the remote. The attraction of the magnets should catch onto the remotes magnets to determine their mounting location. 2. Hold the remote control up to the chosen location. 4. Mark the position of the magnets with a marker.
PAGE 6
AIR MASSAGE KIT INSTALLATION INSTRUCTIONS 5. Apply a small amount of silicone to the magnets and place in the marked position. 7. If programming is unsuccessful, perform a reset by unplugging the system and plugging it in again. From this moment, you have 15 seconds to proceed with another attempt to program. 6. To program the remote, press the second and third buttons on the remote (simultaneously) and hold for 4 seconds. The remote control should synchronize and be ready for use.
PAGE 7
AIR MASSAGE KIT INSTALLATION INSTRUCTIONS TROUBLESHOOTING If the blower is not operating properly: - Verify that the blower motor is plugged into the wall. - Check your electric power supply. Reset the circuit breaker or replace the fuse if necessary. - If the system has been functioning for quite some time, it is possible that the thermic protection has shut oﬀ the motor. Let it cool oﬀ for at least 30 minutes before using it again.