Installation Sheet

ManualsBrandsSignature Hardware ManualsShop All Signature HardwareSignature Hardware Anders 72 Inch Barn Door Hardware Set - Includes Undrilled Track, Rollers, and Matching Hardware

ANDERS BARN DOOR HARDWARE INSTALLATION

GETTING STARTED

BEFORE YOU BEGIN

We recommend consulting a professional if you are

unfamiliar with installing door hardware. Signature

Hardware accepts no liability for any damage to the

hardware, door, walls, ﬂoor, or for personal injury during

installation.

Observe all local building codes.

Unpack and inspect the items for shipping damage. If

any damage is found, contact our Customer Relations

team at 1-866-855-2284.

Ensure that you have gathered all the required

materials that are needed for the installation.

All fasteners must be mounted securely into solid

wood studs, or wood blocking within the wall, for

proper support.

If drilling custom mounting holes into a non-drilled

track, be sure to use a ⅜” diameter titanium coated or

cobalt steel drill bit. Drill slowly and carefully. Holes

should be evenly spaced, and ensure that there is one

mounting hole within 4” of each end.

If your baseboard interferes with your barn door,

additional spacers or longer standoﬀs may be

necessary. Contact Customer Relations for further

assistance.

TOOLS AND MATERIALS:

Adjustable

Wrench

Phillips

Screwdriver

1Anders Barn Door Hardware Installation Instructions

Drill

Tape Measure

Level

Pencil

Drill Bits

Hex Wrench

(Included)

SKU(s): 939904, 939914

Summary of content (5 pages)

PAGE 1
SKU(s): 939904, 939914 ANDERS BARN DOOR HARDWARE INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing door hardware. Signature Hardware accepts no liability for any damage to the hardware, door, walls, ﬂoor, or for personal injury during installation. TOOLS AND MATERIALS: Phillips Screwdriver Adjustable Wrench Drill Observe all local building codes. Unpack and inspect the items for shipping damage.
PAGE 2
ANDERS BARN DOOR HARDWARE INSTALLATION 60”/72” 60”/72” Jump Block x2 Roller x2 Door Guides (x1 ea) Track x1 M8x30 (x4) M10x55 (x4) H H + 1¾” M8x60 (x4) M8x90 (x4) 16” Door Stop x2 Standoﬀ x4 ST4.2x25 (x2) 16” 16” Anchor x2 M10x75 (x4) M10x60 (x4) ⅜” 84” 84” Jump Block x2 16” Standoﬀ x5 16” Track x1 M8x30 (x5) M10x55 (x4) M10x60 (x4) H H + 1¾” M8x60 (x5) M8x90 (x5) 16” Roller x2 Door Guides (x1 ea) ST4.
PAGE 3
ANDERS BARN DOOR HARDWARE INSTALLATION Parts Diagram Masonry Installation 1A. 16” 16” 16” standoﬀ (behind track) H + 1 ¾” jump block 30mm ø8 track roller door stop H = door height 2A.
PAGE 4
ANDERS BARN DOOR HARDWARE INSTALLATION Drywall Installation 3. 1B. 16” 16” 16” drill out ø5.5 1½” 50mm 3½” H + 1 ¾” ø10 H = door height 2B. 4.
PAGE 5
ANDERS BARN DOOR HARDWARE INSTALLATION 5. 7. 1 2 6. Install the door guide. For a door that has been notched on the bottom, use the concealed guide. For a door with standard thickness, use the U-shaped guide. For thicker doors, use the adjustable guide. 8.