Installation Sheet

ManualsBrandsSignature Hardware ManualsBathroom and Shower AccessoriesSignature Hardware Lift and Turn Tub Drain with Swivel Head and Daisy Wheel Overflow - 3-11/16" Thread

1Swivel Head Waste and Overflow Installation Instructions

SWIVEL HEAD WASTE AND OVERFLOW INSTALL

GETTING STARTED

TOOLS AND MATERIALS:

BEFORE YOU BEGIN

We recommend consulting a professional if

you are unfamiliar with installing bathroom

ﬁxtures and plumbing. Signature Hardware

accepts no liability for any damage to the

ﬂoor, walls, plumbing, or personal injury

during installation.

Observe all local plumbing and building

codes.

Unpack and inspect the item for damage. If

any damage is found, contact our

Customer Relations team at

1-866-855-2284.

*not included

Ensure that you have gathered all of the

required materials that are needed for

the installation.

Tape Measure*

Hacksaw*

Plumber’s

Tape*

Adjustable

Wrench*

Neutral Cure

Silicone Sealant*

Damp

Cloth*

Level*

Pipe Wrench*

Thread

Sealant*

Marker*

SKU(s): 921385

Summary of content (8 pages)

PAGE 1
SKU(s): 921385 SWIVEL HEAD WASTE AND OVERFLOW INSTALL BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom ﬁxtures and plumbing. Signature Hardware accepts no liability for any damage to the ﬂoor, walls, plumbing, or personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect the item for damage. If any damage is found, contact our Customer Relations team at 1-866-855-2284.
PAGE 2
SWIVEL HEAD WASTE AND OVERFLOW INSTALL INSTALLATION Use the image and parts list as a reference during drain installation. 1. Drain Elbow 2. Pop-Up Assembly 3. Rubber Sealing Gasket 4. Drain Cover Plate 5. Drain Pipe 6. Overﬂow Elbow 7. Overﬂow Assembly 8. Wedge Gasket 9. Overﬂow Cover Plate 10. Ball Joint 11. Overﬂow Pipe 12. Tee Connector 13. 6” Drain Pipe 14. Escutcheon 15.
PAGE 3
SWIVEL HEAD WASTE AND OVERFLOW INSTALL STEP 1: FITTING AND TRIMMING 1. At your designated drain location, install the 6” drain piece (13) into your under-ﬂoor plumbing. Slide the escutchen (14) onto the drain piece to cover the hole in the ﬂoor. 3. Remove the pop-up assembly (2) from the drain elbow (1). Remove the rubber sealing gasket (3) from the pop-up assembly and insert the assembly into the drain hole. 2. Remove the drain cover plate (4) and the overﬂow cover plate (9) by twisting them out. 4.
PAGE 4
SWIVEL HEAD WASTE AND OVERFLOW INSTALL 5. From under the tub, slide the rubber sealing gasket (3) back onto the pop-up assembly (2). Hand-tighten the pop-up assembly into the drain elbow (1). Ensure that the drain pipe remains in line with the overﬂow hole while tightening. 7. Insert the overﬂow assembly (7) into the tub’s overﬂow hole. Examine the slope of the inner and outer walls of the tub, and place the wedge gasket (8) and rubber sealing gasket accordingly.
PAGE 5
SWIVEL HEAD WASTE AND OVERFLOW INSTALL 9. Remove the overﬂow assembly from the tub. Cut the threading of the overﬂow assembly at the marked location from step 8. 11. Attach the overﬂow pipe (11) to the ball joint (10) using the attached lock nut. Use a level to align the overﬂow pipe so that it is perfectly straight, pointing to the ﬂoor. 10. Remove the ball joint (10) from the overﬂow elbow (6) by unthreading it.
PAGE 6
SWIVEL HEAD WASTE AND OVERFLOW INSTALL 13. Remove the drain and overﬂow pipes and trim them at the marked locations with a hack saw. The saw should contain a blade that is suitable for cutting metal. Set the pipe aside.
PAGE 7
SWIVEL HEAD WASTE AND OVERFLOW INSTALL STEP 2: INSTALLING THE DRAIN 1. Remove the overﬂow elbow (6) from the overﬂow assembly (7). Apply plumber’s tape or thread sealant to the threading on the overﬂow assembly and reattach the overﬂow elbow. 3. Attach the drain pipe (5) to the drain elbow (1). Apply plumber’s tape or thread sealant to the threading before attaching. 2. Attach the overﬂow pipe (11) to the ball joint (10) using the attached lock nut.
PAGE 8
SWIVEL HEAD WASTE AND OVERFLOW INSTALL 5. From inside of the tub, remove he pop-up assembly (2) from the drain elbow (1). Apply a bead of silicone along the underside lip of the pop-up assembly. Apply plumber’s tape or thread sealant to the threading, and reattach. Wipe away any excess silicone with a damp coth. 7. Allow the drain to set for 24 hours to allow the silicone and thread sealant to fully dry.