HOLLYN PUSH-BUTTON SHOWER INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the plumbing, floor, walls, tub, or for personal injury during installation. TOOLS AND MATERIALS: Plumbers Tape Tape Measure Adjustable Wrench Drill Phillips Screwdriver Observe all local plumbing and building codes. Unpack and inspect the item for shipping damage.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION INSTALLATION 1. To prepare for installation, wood blocking should be installed between the two studs where the valve will mount. Be careful not to set the valve too far back into the wall. Use the sticker on the side of the valve for guidance. 3. Connect all inlet and outlet pipes as shown in the diagram below. outlet outlet Important: Take into consideration the thickness of the finished wall materials, such as tile, when calculating measurements. hot water 2.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 5. At each of the four marked mounting hole locations, drill an 8mm diameter hole. 7. Connect the hot and cold water feed lines to the installed valve. ø8 cold water hot water 6. Insert an anchor into each of the four drilled mounting holes, then affix the valve to the wall using self-tapping screws. Use the level on the mounting box to ensure the valve remains straight. 8. Remove the protective cover and turn off the switch.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 9. Plug the outlets and turn the switch on. Check the pressure and ensure that there are no leaks. Then, replace the protective cover that was removed in step 8. IMPORTANT: COMPLETE THE CONSTRUCTION OF YOUR WALL, INCLUDING ANY FINISHED WALL MATERIALS SUCH AS TILE, BEFORE PROCEEDING WITH THE REMAINDER OF THE INSTALLATION. switch open 11. Ensure that the switch is open. Place the positioning bar against the wall as shown.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 13. Place the positioning bar against the wall as shown. Adjust the height of the M6 screw until it meets the surface of the backside of the positioning bar. Then, tighten the M6 screw nut with the wrench. this side against the wall 15. Replace the M6 screws with the shorter M6 screws. Then, adjust the screws as indicated in step 12. M6 screw head should be even with backside of positioning bar shorter M6 screw 14. Turn on the switch.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 17. Remove the protective sleeve from the valve body. Place the trim plate onto the body and M6 screws. 19. Attach the control handle to the installed valve body. Ensure that the slot mark on the spindle, the stop collar, the safety button, and the 38°C mark are all aligned. Tighten the M4 screw then insert the screw cap.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION SHOWER HEAD INSTALLATION: WAY 1 1. To prepare for installation, wood blocking should be installed between the two studs where the valve will mount. Be careful not to set the valve too far back into the wall. Use the sticker on the side of the valve for guidance. 3. Use the four holes on the shower holder as a guide to mark mounting hole locations on the wall, as shown in the diagram below. Use a level to ensure an even installation.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 5. Insert an anchor into each of the four drilled mounting holes, then affix the shower holder to the wall using self-tapping screws. 7. Clean pipes to get rid of dirt and turn on water to test pressure. Then, check for leaks. Anchor Self-tapping screw Phillips screwdriver 6. Tighten screws and use the level to ensure the shower holder remains straight, as shown in the diagram below. 8. Put on the protective cover, as shown.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 9. Use the pipe bracket as a guide to mark the two mounting hole locations on the wall, as shown in the diagram below. 11. Attach the bracket to the wall using self-tapping screws. Pipe bracket Reinforcing rod 10. At both of the marked mounting hole locations, drill an 8mm diameter hole. Then, insert the anchors into the two holes. 12. Proceed to wall installations, including tile. Use markings on the protective cover for guidance.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 14. Wrap plumbers tape around the pipe nipples and screw them into the wall. STOP Filtering net Pipe nipple IMPORTANT: COMPLETE THE CONSTRUCTION OF YOUR WALL, INCLUDING ANY FINISHED WALL MATERIALS SUCH AS TILE, BEFORE PROCEEDING WITH THE REMAINDER OF THE INSTALLATION. 13. Pull off the protective cover and unscrew the two plugs. 15. Attach the shower head to the wall. Then, fasten with the M6 screw.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 16. After installation, run the water to remove any debris or dirt. 2. Attach the mounting plate to the plug and tighten with a S7 wrench. Then, put on the protective cover over the plug. Mounting plate Plug Protective Cover INSTALLATION: WAY 2 3. Use the four holes on the shower holder and the four holes on the mounting plate as a guide to mark mounting hole locations on the wall, as shown in the diagram below. Use a level to ensure an even installation. 1.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 4. At each of the marked mounting hole locations, drill an 8mm diameter hole. 6. To ensure an even installation use a level, then tighten the shower holder and locating plate. Hole Rough wall Horizontal alignment Drill Slot 5. Insert an anchor into each of the drilled mounting holes, then affix the mounting plate to the wall using self-tapping screws. 7. To test the pressure, turn on the water and make sure there are no leaks.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 8. Use the pipe bracket as a guide to mark the two mounting hole locations on the wall, as shown in the diagram below. 10. Attach bracket to wall using self-tapping screws. Pipe bracket Reinforcing rod 9. At both of the marked mounting hole locations, drill an 8mm diameter hole. Then, insert the anchors into the two holes. Hole 11. Fill in the slot with cement and proceed to wall installation, including tile.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 13. Wrap plumber’s tape around the pipe nipples and screw them into the wall. STOP Filtering net Pipe nipple IMPORTANT: COMPLETE THE CONSTRUCTION OF YOUR WALL, INCLUDING ANY FINISHED WALL MATERIALS SUCH AS TILE, BEFORE PROCEEDING WITH THE REMAINDER OF THE INSTALLATION. 12. Pull off the protective cover and unscrew the two plugs. 14. Attach the shower head to the wall. Then, fasten with the M6 screw.
HOLLYN PUSH-BUTTON SHOWER INSTALLATION 15. After installation, run the water to remove any debris or dirt.
