HOLLYN PUSH-BUTTON SHOWER SYSTEM BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the plumbing, floor, walls, tub, or for personal injury during installation. TOOLS AND MATERIALS: Plumbers Tape Tape Measure Adjustable Wrench Drill Phillips Screwdriver Observe all local plumbing and building codes. Unpack and inspect the item for shipping damage.
HOLLYN PUSH-BUTTON SHOWER SYSTEM VALVE INSTALLATION 1. To prepare for installation, wood blocking should be installed between the two studs where the valve will mount. Be careful not to set the valve too far back into the wall. Use the sticker on the side of the valve for guidance. 3. Wrap the pipe couplings with plumber’s tape and connect them to the valve body. Important: Take into consideration the thickness of the finished wall materials, such as tile, when calculating measurements.
HOLLYN PUSH-BUTTON SHOWER SYSTEM 5. Use a level to adjust the valve body. Mark the location of the mounting holes on the wood blocking. 7. Insert the provided anchors into each of the drilled holes. Affix the valve using self-tapping screws. anchor self-tapping screws 6. Drill holes at each of the six marked mounting hole locations using an 8 mm drill bit. 8. Use a level to ensure that the valve is mounted straight. Make adjustments as needed.
HOLLYN PUSH-BUTTON SHOWER SYSTEM 9. Flush the water lines to get rid of any dirt or debris, then connect the water feed lines. Hot water should be connected to the upper inlet, cold water to the lower inlet. 11. Plug the outlets and open the two switches on the left. Flush the water and check for leaks. Then, replace the protective cover. hot water switch open cold water flush water flush water 10. Remove the protective cover from the valve body. turn on the switch.
HOLLYN PUSH-BUTTON SHOWER SYSTEM 13. Remove all protective covers and caps once the finished wall is completed. 15. Replace with shorter adjustable threaded adapters and caps. shorter threaded adapters threaded adapter protective cover 14. With the switch open, place the positioning bar against the wall as shown. If the upper surface of the cap is lower than the front side of the positioning bar, adjust the cap height so that it is even with the front side. Then, do as shown in step 17.
HOLLYN PUSH-BUTTON SHOWER SYSTEM 17. Place the trim plate onto the installed valve body. Wrap the hand shower’s threaded adapter with plumber’s tape and thread it into its outlet. 19. Attach the control handle to the installed valve body. Ensure that the slot mark on the spindle, the stop collar, the safety button, and the 38°C mark are all aligned. Tighten the M4 screw then insert the screw cap.
HOLLYN PUSH-BUTTON SHOWER SYSTEM SHOWER HEAD INSTALLATION 21. Connect the hand shower and hose to the cradle. hand shower 1. To prepare for installation, wood blocking should be installed between the two studs where the valve will mount. Be careful not to set the valve too far back into the wall. Use the sticker on the side of the valve for guidance. Important: Take into consideration the thickness of the finished wall materials, such as tile, when calculating measurements. hose 22.
HOLLYN PUSH-BUTTON SHOWER SYSTEM 3. Use the four holes on the shower holder as a guide to mark mounting hole locations on the wall, as shown in the diagram below. Use a level to ensure an even installation. 5. Insert an anchor into each of the four drilled mounting holes, then affix the shower holder to the wall using self-tapping screws. Anchor Self-tapping screw Pencil 4. At each of the four marked mounting hole locations, drill an 8mm diameter hole. Phillips screwdriver 6.
HOLLYN PUSH-BUTTON SHOWER SYSTEM 7. Clean pipes to get rid of dirt and turn on water to test pressure. Then, check for leaks. 9. Use the pipe bracket as a guide to mark the two mounting hole locations on the wall, as shown in the diagram below. Pipe bracket Reinforcing rod 8. Put on the protective cover, as shown. 10. At both of the marked mounting hole locations, drill an 8mm diameter hole. Then, insert the anchors into the two holes.
HOLLYN PUSH-BUTTON SHOWER SYSTEM 11. Attach the bracket to the wall using self-tapping screws. STOP IMPORTANT: COMPLETE THE CONSTRUCTION OF YOUR WALL, INCLUDING ANY FINISHED WALL MATERIALS SUCH AS TILE, BEFORE PROCEEDING WITH THE REMAINDER OF THE INSTALLATION. 12. Proceed to wall installations, including tile. Use markings on the protective cover for guidance. 13. Pull off the protective cover and unscrew the two plugs.
HOLLYN PUSH-BUTTON SHOWER SYSTEM 14. Wrap plumbers tape around the pipe nipples and screw them into the wall. Filtering net 16. After installation, run the water to remove any debris or dirt. Pipe nipple INSTALLATION: WAY 2 15. Attach the shower head to the wall. Then, fasten with the M6 screw. 1. Apply plumber’s tape to the threads of the two plugs, straight connector, and pipe elbow. Screw the two plugs, straight connector, and pipe elbow into the shower holder as shown.
HOLLYN PUSH-BUTTON SHOWER SYSTEM 2. Attach the mounting plate to the plug and tighten with a S7 wrench. Then, put on the protective cover over the plug. 4. At each of the marked mounting hole locations, drill an 8mm diameter hole. Hole Rough wall Mounting plate Drill Plug Protective Cover 3. Use the four holes on the shower holder and the four holes on the mounting plate as a guide to mark mounting hole locations on the wall, as shown in the diagram below. Use a level to ensure an even installation.
HOLLYN PUSH-BUTTON SHOWER SYSTEM 6. To ensure an even installation use a level, then tighten the shower holder and locating plate. 8. Use the pipe bracket as a guide to mark the two mounting hole locations on the wall, as shown in the diagram below. Horizontal alignment Pipe bracket Reinforcing rod 7. To test the pressure, turn on the water and make sure there are no leaks. 9. At both of the marked mounting hole locations, drill an 8mm diameter hole. Then, insert the anchors into the two holes.
HOLLYN PUSH-BUTTON SHOWER SYSTEM 10. Attach bracket to wall using self-tapping screws. STOP IMPORTANT: COMPLETE THE CONSTRUCTION OF YOUR WALL, INCLUDING ANY FINISHED WALL MATERIALS SUCH AS TILE, BEFORE PROCEEDING WITH THE REMAINDER OF THE INSTALLATION. 11. Fill in the slot with cement and proceed to wall installation, including tile. 12. Pull off the protective cover and unscrew the two plugs.
. After installation, run the water to remove any debris or dirt.
