Installation Sheet

ManualsBrandsSignature Hardware ManualsShower FaucetsSignature Hardware Pendleton Pressure Balanced Tub and Shower Trim Package - Rough In Included

1.800.221.3379

PENDLETON

PRESSURE BALANCE SHOWER SET

SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON

SKU: 948663, 948672

REVISED 01/30/2021

CODES: SHPT8020G, SH4001, SHPT8030G

GETTING STARTED

BEFORE YOU BEGIN

We recommend consulting a professional if you are



Hardware accepts no liability for any damage to the

plumbing, shower, wall, or for personal injury during

installation.

Observe all local plumbing and building codes.

Unpack and inspect the product for shipping

damage. If any damage is found, contact our

Customer Relations team at 1-800-221-3379.

Ensure that you have gathered all the required

materials that are needed for the installation.

TOOLS AND MATERIALS:

HERRAMIENTAS Y MATERIALES:

ANTES DE COMENZAR

Le recomendamos que consulte a un profesional si no

sabe cómo instalar accesorios de plomería. Signature

Hardware no asume ninguna responsabilidad con

respecto a los daños causados a la plomería, la ducha,

la pared, ni por daños personales que ocurran durante

la instalación.

Cumpla con todas las normas locales de plomería y

construcción.

Retire el producto del empaque y veriﬁque si se

produjeron daños durante el envío. Si encuentra algún

daño, comuníquese con nuestro equipo de Servicio al

cliente al 1-800-221-3379.

CÓMO COMENZAR

Asegúrese de haber reunido todos los materiales

necesarios para la instalación.

Adjustable Wrench

Llave Ajustable

Flathead

Screwdriver

Destornillador de

cabeza plana

Phillips

Screwdriver

Destornillador

Phillips

Safety Glasses

Gafas de seguridad

Keyhole Saw

Sierra de punta

Tape Measure

Cinta métrica

Neutral Cure

Silicone Sealant

Sellador de silicona

de curado neutro

Groove Joint Plier

Pinzas ajustable

Plumbers Tape

Cinta Selladora

Para Rosca

Thermometer

Termómetro

Strap Wrench

Llave de correa

Summary of content (13 pages)

PAGE 1
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 BEFORE YOU BEGIN TOOLS AND MATERIALS: HERRAMIENTAS Y MATERIALES: We recommend consulting a professional if you are unfamiliar with installing plumbing �xtures. Signature Hardware accepts no liability for any damage to the plumbing, shower, wall, or for personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect the product for shipping damage.
PAGE 2
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 Copper (Soldering)/Cobre (Soldar) If you are replacing your plumbing valve, please review the common plumbing methods illustrated below (Copper, IPS). Remove the existing handle and valve trim before replacing your valve. Please follow all local building and plumbing codes. Si estás cambiando tu válvula de plomería, consulta los dos métodos comunes que aparecen más abajo (Cobre, IPS).
PAGE 3
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 VALVE INSTALLATION INSTALACIÓN DE LA VÁLVULA 3a. Thin Wall Installation: Are usually built up with materials such as �berglass tub surrounds and will be the main source of support for the valve. The plaster guard (1) remains attached to the valve. 1. Shut o� the water supply. 3a.
PAGE 4
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 6. With Tub Outlet: Wrap plumbers’ tape around the pipe threads in a clockwise direction. Connect the hot and cold water supply lines (1), the shower outlet pipe (2), and tub outlet pipe (3) by threading them onto the valve body (5) in a clockwise direction. Tighten the pipes to the valve body (5) with a pipe wrench. Connect the pipe elbows (4) to the end of the shower outlet and tub outlet pipes.
PAGE 5
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 8. If the hot and cold inlets are reversed (hot on right and cold on left), remove bonnet (1) from the valve body (3) with reversed supply connections. Rotate the cartridge (2) 180°, so H appears on the right. Install the cartridge making sure that the key is fully engaged with the slot in the valve body (3). Slide the bonnet (1) over the cartridge (2) and thread them onto the valve body (3).
PAGE 6
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 9. Use two 1/2" iron pipe plugs to seal both shower outlet and tub spout outlet. Turn cartridge stem counterclockwise to full on mixed position. Turn on hot and cold water lines to full open position for one minute each. Check for leaks. Shut o� water at faucet. Slowly remove pipe plugs from tub and shower outlets to relieve pressure. 10.
PAGE 7
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 13. Rotate the lever counterclockwise until the water is to the maximum desired temperature, not to exceed 120 degrees F/49 degrees C. Seasonal maintenance of the maximum outlet temperature may be required due to changes in groundwater temperature. 12. Before adjusting the temperature, remove the plastic cap (1) from the valve body (2) by twisting the cap in a clockwise direction. 12.
PAGE 8
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 15. For colder water, adjust the limit stop ring (1) in a clockwise direction and reinstall the limit stop ring (1) onto the cartridge assembly (2). For hotter water, adjust the limit stop ring (1) in a counterclockwise direction and reinstall the limit stop ring (1) onto the cartridge assembly (2). 14.
PAGE 9
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 INSTALLATION INSTALACIÓN 16. If faucet leaks from spout, shut o� the water supplies and replace the cartridge (1). Note: Install cartridge (1) correctly for proper handle rotation. 1. Screw nut (1) onto thread section of valve body. Insert the brass stem extension (2) to valve body. Tighten screw (3). 16.
PAGE 10
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 4. Install tub spout. Press tub spout onto pipe until spout is properly positioned and �ush to the �nished wall. Tighten screw (1) located at the bottom of spout with Allen wrench (Hex: 4.0mm). 3. Insert the long end of the shower arm (2) through the �ange (1), and wrap plumbers’ tape around the long end of the shower arm (2) in a clockwise direction, as shown.
PAGE 11
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 5a. Flushing For Shower Only: Turn on hot and cold water supply lines allowing water to �ow from shower outlet (1) until all foreign matter has cleared the line. Pressure must be approximately equal on both hot and cold sides for valve to function properly. 5a.
PAGE 12
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 2 1 3 No. 1 2 3 Part Name / Nombre de pieza Part No. Plaster Guard / Protector de yeso ACF4001GRD Cartridge / Cartucho ACF4001UCRT Stop Valve / Válvula con graduacione ACF4001STOP 12 1.800.221.
PAGE 13
P E N D L E TO N PRESSURE BALANCE SHOWER SET SET DE DUCHA DE PRESIÓN BALANCEADA PENDLETON SKU: 948663, 948672 4 3 1 No. 2 Part Name / Nombre de pieza Part No. 1 Handle / Llave OBPF713385* 2 Screw / Tornillo OBPF150142 3 Connector / Conector OBPF870350 4 Nut / Tuerca OBPF56082 13 1.800.221.