Installation Sheet

ManualsBrandsSignature Hardware ManualsPlumbingMorgan 71" Copper Double Slipper Air Tub with Integrated Overflow and Rolled Rim - Less Drain Assembly

1Copper Freestanding Tub Installation Instructions

COPPER FREESTANDING TUB

GETTING STARTED

TOOLS AND MATERIALS:

BEFORE YOU BEGIN

We recommend consulting a professional if

you are unfamiliar with installing bathroom

ﬁxtures and plumbing. Signature Hardware

accepts no liability for any damage to the

ﬂoor, walls, plumbing, or personal injury

during installation.

Observe all local plumbing and building

codes.

Unpack and inspect the tub for damage. If

any damage is found, contact our

Customer Relations team at

1-866-855-2284.

*not included

Ensure that you have gathered all of the

required materials that are needed for

the installation.

Ensure that your bathroom ﬂoor is

adequately supported, and the ﬁnished

ﬂoor is level.

Keep the plumbing connections around

the tub easily accessible for any future

maintenance that may be necessary.

PLANNING

Use the tub’s PDF speciﬁcation sheet as a

reference when planning your layout. The

speciﬁcation sheet can be found and

downloaded from the product page on our

website.

Because the tub speciﬁcation

measurements are approximate and slight

variations may occur, we highly recommend

performing any rough-in procedures with

the tub on site. For on-site rough-in

information, go to the appropriate drain

installation section.

Pencil*

Tape Measure*

Straight Edge*

Hacksaw*

Thread Sealant*

Plumber’s Tape*

Adjustable

Wrench*

Neutral Cure

Silicone Sealant*

Damp

Cloth*

Level*

Plumb Line*

Summary of content (7 pages)

PAGE 1
COPPER FREESTANDING TUB BEFORE YOU BEGIN PLANNING We recommend consulting a professional if you are unfamiliar with installing bathroom ﬁxtures and plumbing. Signature Hardware accepts no liability for any damage to the ﬂoor, walls, plumbing, or personal injury during installation. Use the tub’s PDF speciﬁcation sheet as a reference when planning your layout. The speciﬁcation sheet can be found and downloaded from the product page on our website. Unpack and inspect the tub for damage.
PAGE 2
COPPER FREESTANDING TUB INSTALLATION Proceed to the appropriate drain conﬁguration to complete rough-in and installation. TUB AND DRAIN WITHOUT OVERFLOW 1. Set the tub in the desired installation location and mark the drain hole location on the ﬂoor. 2. Move the tub away from the installation location so that plumbing can be installed. The drain pipe should extend approximately 6" above the ﬁnished ﬂoor. 3.
PAGE 3
COPPER FREESTANDING TUB 5. Apply 100% neutral cure silicone sealant to the underside of the drain ﬂange and thread it through the tub and into the drain pipe. Apply thread sealant or plumber’s tape to the threaded connection to ensure a water-tight seal. Tighten by hand. Wipe away any excess sealant using a damp cloth. 6. Fill the tub with water to check for any leaks from the connections. Verify that the drain is working properly.
PAGE 4
COPPER FREESTANDING TUB TUB AND DRAIN WITH OVERFLOW 1. Set the tub in the desired installation location and drop a plumb line from the center of the overﬂow hole to the ﬂoor. This will determine your drain location. Mark the drain hole location on the ﬂoor. 2. Move the tub away from the installation location so that the plumbing can be installed. Place the drain pipe at the appropriate height for waste and overﬂow piping.
PAGE 5
COPPER FREESTANDING TUB 6. The overﬂow tee (A) will be attached at the points where the drain pipes intersect (B). 8. Remove the drain and overﬂow assembly from the tub, and trim the pipes at the marked locations with a hacksaw. Make sure that the blade is suitable for cutting metal. A B 7. Measure and mark each pipe so that the end of the pipe reaches at least a little bit over halfway into the overﬂow tee. 9. Apply thread sealant or plumber’s tape to the threaded ends of all pipes prior to assembly.
PAGE 6
COPPER FREESTANDING TUB 10. Apply 100% neutral cure silicone sealant to the underside of the drain ﬂange and thread it through the tub and into the drain pipe. Apply thread sealant or plumber’s tape to the threaded connection to ensure a water-tight seal. Tighten by hand. Wipe away any excess sealant using a damp cloth. 14. When your tub is in place and all the connections have been made, ﬁll the tub with water to check for any leaks from the connections.
PAGE 7
COPPER FREESTANDING TUB CLEANING AND MAINTENANCE To protect a copper ﬁnish, it is recommended that a coating of wax is applied to the surface. Most wax products have natural and added UV ﬁlters that help guard against color and ﬁnish degradation. Wax should be applied as often as necessary, depending upon usage. It is recommended that you use a cleaner or polish that is designed speciﬁcally for copper products. You may use a gentle soap, such as dish washing liquid and warm water.