Installation & Assembly

ManualsBrandsSignature Hardware ManualsBathRobertson 49" Single Bathroom Vanity Set

1Single Bowl Vessel Vantiy Installation Instructions

SINGLE BOWL VESSEL VANITY

GETTING STARTED

TOOLS AND MATERIALS:

BEFORE YOU BEGIN

We recommend consulting a professional if you are

unfamiliar with installing bathroom ﬁxtures and

plumbing. Signature Hardware accepts no liability for any

damage to the ﬂoor, walls, plumbing, vanity cabinet, sink,

counter top, or personal injury during installation.

Observe all local plumbing and building codes.

Unpack and inspect the vanity for damage. If any

damage is found, contact our Customer Relations team

at 1-866-855-2284.

*not included

Ensure that you have gathered all the required

materials that are needed for the installation.

Ensure that your bathroom ﬂoor is adequately

supported, and the ﬁnished ﬂoor is level.

Ensure that there is adequate support behind the

bathroom wall before installation.

PLANNING

Use the vanity’s PDF speciﬁcation sheet as a reference

when planning your layout. The speciﬁcation sheet can

be found and downloaded from the product page on

our website.

Because the vanity speciﬁcation measurements are

approximate and slight variations may occur, we highly

recommend performing any rough-in procedures with

the vanity on site.

Tape Measure*Marker*

Drill*

Screwdriver*

Stud Finder

Level

Neutral Cure

Silicone Sealant

Damp Cloth

Wood Shims

NEVER LIFT THE VANITY TOP FLAT NEVER CARRY THE VANITY TOP FLAT

Summary of content (5 pages)

PAGE 1
SINGLE BOWL VESSEL VANITY BEFORE YOU BEGIN PLANNING We recommend consulting a professional if you are unfamiliar with installing bathroom ﬁxtures and plumbing. Signature Hardware accepts no liability for any damage to the ﬂoor, walls, plumbing, vanity cabinet, sink, counter top, or personal injury during installation. Use the vanity’s PDF speciﬁcation sheet as a reference when planning your layout. The speciﬁcation sheet can be found and downloaded from the product page on our website.
PAGE 2
SINGLE BOWL VESSEL VANITY Step 1: Cabinet Installation 1. Determine the location where you would like to install your vanity. 3. Place the vanity in the installation location. Verify that the vanity cabinet is level. If the vanity is not level, adjust the feet (if applicable) or use wooden shims to adjust as necessary. 2. Locate and mark the location of the studs to which you will fasten your vanity. You can locate studs by using a stud ﬁnder. 4.
PAGE 3
SINGLE BOWL VESSEL VANITY Step 2: Counter Top Installation 1. Apply a bead of silicone sealant around the top edge of the vanity cabinet. 3. If you are installing a side-splash and/or back-splash, place a generous amount of silicone sealant on the back of it and press it into place against your bathroom wall. Fill any gaps that are left with silicone sealant. Wipe away any excess sealant with a damp cloth. 2.
PAGE 4
SINGLE BOWL VESSEL VANITY Step 3: Sink Installation 5. For stone tops, such as marble and granite, it is recommended that you apply a high-quality sealer to protect from staining and discoloration. Stone sealer should be reapplied once or twice per year, depending upon usage. 1. Carefully place your vessel sink upside down on the counter top. Apply a generous amount of silicone sealant to the base of the sink where it will rest on the counter. Stone Sealer 2.
PAGE 5
SINGLE BOWL VESSEL VANITY 3. If desired, apply a continuous bead of silicone sealant around the perimeter of the sink base for additional stability. 5. Let the assembled vanity sit for 24 hours to allow all the silicone sealant to fully dry. Once dry, proceed to the installation of your faucet and drain assemblies. Note: In some situations, it may be necessary to cut the inner cabinet shelves to allow space for your drain’s P-traps. 4. Remove any excess sealant to complete the sink installation.