ASSEMBLY INSTRUCTIONS Page 1 of 11
To insert a cam lock: (Please read below instructions before assembling) Diagram A 1. Insert cam screw into hole as shown in diagram A . Diagram B Diagram C Make sure not to insert the cam screw: Too deep as shown in figure B as this will cause the cam screw to be misaligned and unable to interlock properly. Also avoid inserting the cam screw too close to the surface of the hole as shown in figure C, as this will cause the cam lock to be too loose, and not interlock properly. 2.
Part List 1 Quantity of 1 Top Panel 5 Quantity of 1 Front Leg(Right) 6 Quantity of 1 Quantity of 1 10 Quantity of 1 Quantity of 1 7 Quantity of 1 11 Rear Leg(Rght) Page 3 of 11 Quantity of 1 8 Quantity of 1 Door(Right) Quantity of 2 Connect Bar 15 4 Side Panel(Left) Quantity of 1 Door(Left) Back Panel(Right) Quantity 14 of 1 Rear Leg(Left) 3 Bottom Shelf Side Panel(Right) Back Panel(Left) 13 Quantity of 1 Divider Panel Center Divider 9 2 12 Front Leg(Left) Quantity of
Hardware List A Quantity of 22 Cam-Lock E Handle with Bolt Quantity of 28 Wood Dowel Quantity of 4 F Quantity of 2 J Connect Block C Quantity of 2 Bolt Quantity of 2 Magnet with Screw Connect Block I B G D Screw Quantity of 1 H Connect Plate with Screw Door Pin Quantity Quantity K L of 6 of 1 Anchor with Screw Allen Wrench Page 4 of 11 Quantity of 22 Cover Quantity of 4 Quantity of 14
1 10 9 15 13 6 5 4 11 11 8 7 14 12 2 3 Page 5 of 11
Step1: B: C 2pcs 2pcs 5 B B C 2 C Assemble Divider (5) to Divider Panel (2) using Bolts (C) and Wood Dowels (B) as shown above. Step 2: A: 6sets B: 6pcs 4 6 A A B 11 A B A 11 A 14 15 Assemble Rear Legs (14&15)to Side Panels (4&6) and Connect Bars (11) using Cam-Locks (A) and Wood Dowels (B) as shown above.
Step 3: A: 4sets B: 4pcs E 2pcs D: 4pcs 6 A B 5 D B D A 2 A E 15 A A B B 4 A D 14 D E Assemble Divider Panel (2) to Side Panels (4&6) using Cam-Locks (A) and Wood Dowels (B) as shown above. Assemble Connect Block (E) to Rear Legs (14&15)using Screws (D) as shown above. Step 4: D: 3 E D 15 14 E D Assemble Bottom Shelf (3) to Rear Legs (14&15) using Screws (D) as shown above.
Step 5: A A: 6sets B: 6pcs E 2pcs D: 8pcs 13 A B E B D Fig.1. 12 B 12 D E A A D B 13 B D E 3 A D 15 14 1). Assemble Connect Blocks (E) to Front Legs (12&13) using Screw(D) ,refer t o Fig.1. 2). Then assemble Front Legs (12&13) to Side Panels (4&6) , Bottom Shelf (3) and Connect Bars (11) using Cam-Locks (A) Wood Dowels (B) and Screws (D) as shown above.
Step 7: G F: 2sets G: 1set G 1 F F 1). Attach Magnets (F) to the bottom of Top Panel (1) using included Screws (F) as shown above. 2).Attach Connect Plate (G) to the bottom of Top Panel (1) using included Screws(G). Step 8: 1 B A A B B A A B A A B: 10pcs L 14pcs B A L 6pcs A B A B A B 6 B L A 14 B A: 4 5 L L L 13 12 Assemble Top Panel (1) to Legs (12&13&14&15) and Divider (5) Side Panels (4&6) using Wood Dowels (B) and Cam-Locks (A) as shown above.
Step 9: H H: I: 4pcs 2sets I H 8 7 I H H Insert Door Pins (H) into the hole on the two ends of Door Panels (7&8). Then attach Door Handles (I) to Door Panels (7&8) using included bolts (I). Step 10: 1 1 7 Fig.2. 7 2 8 7 2 Fig.1. Connect Door Panels (7&8) to Divider Panel (2) as drawing Fig.1. Then press down Door Pin (H) ( see Fig.2.) and hold the Door Panel carefully into the cabinet with the upper pin popping up into the hole of Top Panel (1).
Step 11: D: J: 6pcs 6pcs J J 10 J D D 9 D D J D J D J D 9 J 2 Attach Connect Blocks (J) to Rear Legs (14 &15) ,Divider (2) and Top Panel (1) to hold Back Panels (9&10) using Screws (D) as shown above. Step 12: K wall K wall 1 5 K 10 For your safety, please attach this unit to the wall by Anchor with Screws ( K).
