Integrated Refrigeration Installation Guide BUILT-IN REFRIGERATION SKSCF1801P SKSCF2401P SKSCF3001P SKSCR2401P SKSCR3001P www.signaturekitchensuite.com MFL67410814_Rev.04 Copyright © 2017 - 2018 Signature Kitchen Suite. All Rights Reserved.
Table of Contents
SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS This guide contains many important safety messages. Always read and obey all safety messages. This is the safety alert symbol. It alerts you to safety messages that inform you of hazards that can kill or hurt you or others or cause damage to the product. All safety messages will be preceded by the safety alert symbol and the hazard signal word WARNING, or CAUTION.
operation and use without twisting or deforming. bending. The product must be level both horizontally and vertically. Electrical Connection Use a dedicated outlet. Plug in the power plug with the power cord facing downward. When installing or moving the refrigerator, be careful not to roll over or damage the power cord. Do not squeeze or crush the cord or plug when pushing the refrigerator in. Do not allow the power cord to be bent, crushed, or damaged.
If the supply cord is damaged, it must be replaced by the manufacturer or its service CAUTION Do not remove the cover of the automatic ice dispenser. The internal mechanism of the icemaker can cause injury if handled. Do not stick your hands under the refrigerator. Sharp edges, fans, and wires may cause an injury Save these instructions for the local inspector's use. Observe all governing codes and ordinances. Installer: Leave these instructions with the consumer.
Before Installation WARNING Choosing the Install Location Temperature and Humidity The appliance should be installed in a dry, well ventilated area. tions. oven or radiator. Anti-tip Devices WARNING: Tip Hazard securely installed. installing the appliance in a stable position is to use the supplied anti-tip devices. If the enclosure is sturdy enough, attaching the appliance to the upper and side walls of the encloIf in doubt, contact an architect or structural engineer.
Enclosure nals of the opening to make sure corners are square. cabinets. Make sure the enclosure or the adjacent cabinets are securely connected to the Floor WARNING mance.
Electrical Requirements WARNING The receptacle must be installed by a licensed electrician only. Grounding This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for the electric current. WARNING: Improper connection of the equipment grounding conductor may result in electric if you are in doubt as to whether the appliance has been properly grounded.
Water Connection CAUTION ily accessible.
SKSCF1801P – 18" INTEGRATED FREEZER COLUMN CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION, SINGLE COLUMN NOTE depth adjacent cabinets. sides and the top of the cutout opening. The shaded area will be visible after installation. ELECTRICAL Note: GFI (ground fault interrupter) is not recommended. WATER LINE A cold water supply is required for automatic icemaker operation. The water pressure must be between 20 and 120 psi. date a bend leading into the water line connection.
INSTALLATION CLEARANCES NOTE The installation must allow for clearances to adjacent walls or cabinets. This freezer is equipped with a 2-position door stop. restricted. The door handle depth must be added to the dimension where noted to determine the total clearance required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used.
SKSCF2401P – 24" INTEGRATED FREEZER COLUMN SKSCR2401P – 24" INTEGRATED REFRIGERATOR COLUMN CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION, SINGLE COLUMN NOTE depth adjacent cabinets. sides and the top of the cutout opening. The shaded area will be visible after installation. ELECTRICAL Note: GFI (ground fault interrupter) is not recommended. WATER LINE A cold water supply is required for automatic icemaker operation. The water pressure must be between 20 and 120 psi.
INSTALLATION CLEARANCES NOTE equipped with 2-position door stops. restricted. The door handle depth must be added to the dimension where noted to determine the total clearance required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used.
SKSCF3001P – 30" INTEGRATED FREEZER COLUMN SKSCR3001P – 30" INTEGRATED REFRIGERATOR COLUMN CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION, SINGLE COLUMN NOTE mm) depth adjacent cabinets. sides and the top of the cutout opening. The shaded area will be visible after installation. ELECTRICAL Note: GFI (ground fault interrupter) is not recommended. WATER LINE The water pressure must be between 20 and 120 psi. commodate a bend leading into the water line connection.
INSTALLATION CLEARANCES NOTE ance to adjacent cabinets or walls is restricted. The door handle depth must be added to the dimension where noted to determine the total clearances required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used.
SKSCF1801P – 18" INTEGRATED FREEZER COLUMN 3/4" (19 MM) CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION NOTES custom door panels are required. For custom panels: Use templates provided with units to pre-drill holes for mounting panel brackets (provided with unit). Adjustment screws and instructions also provided with units. DESIGN TIPS the optional frame kit may be used. If using custom panels, a custom toe kick is required. Custom handles are required for installation.
OPTIONAL ACCESSORIES – FLUSH OR PROUD INSTALLATION COLUMN This unit can be installed with an optional stainless steel panel kit. The kit includes one door panel, one toe kick and one handle. This kit is reversible and can be used in both right hand and left hand door swing installations.
SKSCF2401P – 24" INTEGRATED FREEZER COLUMN SKSCR2401P – 24" INTEGRATED REFRIGERATOR COLUMN 3/4" (19 MM) CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION NOTES custom door panels are required. For custom panels: Use templates provided with units to pre-drill holes for mounting panel brackets (provided with unit). Adjustment screws and instructions also provided with units. DESIGN TIPS the optional frame kit may be used. If using custom panels, a custom toe kick is required.
OPTIONAL ACCESSORIES – FLUSH OR PROUD INSTALLATION This unit can be installed with an optional stainless steel panel kit. The kit includes one door panel, one toe kick and one handle. This kit is reversible and can be used in both right hand and left hand door swing installations.
SKSCF3001P – 30" INTEGRATED FREEZER COLUMN SKSCR3001P – 30" INTEGRATED REFRIGERATOR COLUMN 3/4" (19 MM) CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION NOTES custom door panels are required. For custom panels: Use templates provided with units to pre-drill holes for mounting panel brackets (provided with unit). Adjustment screws and instructions also provided with units. DESIGN TIPS optional frame kit may be used. Brushed aluminum handles are available as an optional accessory.
OPTIONAL ACCESSORIES – FLUSH OR PROUD INSTALLATION This unit can be installed with an optional stainless steel panel kit. The kit includes one door panel, one toe kick and one handle. This kit is reversible and can be used in both right hand and left hand door swing installations. installation.
Required Accessories and Tools Supplied Accessories Installation instructions Operating instructions Installation kit Other Stepladder Tools Cordiess screwdriver and magnetic holder driver materials Wood screws in different sizes Thin plywood sheet, particle board or Suitable material for covering and protecting furniture (e.g. protective sheets) Adhesive tape Signature Kitchen Suite. Multigrip pliers Adjustable wrench Cutter with adustable blade Metal tape measure, folding rule Square and 4'(1.
Installation The following installation instructions describe the installation steps for various appliance types: The diagrams may be a general representation of your appliance.
Unpacking WARNING To avoid serious injury or product damage: the appliance. Check appliance for damage in transit. If in doubt, contact your dealer. 1. Remove the packaging carton, being careful not to damage the surface of the appliance. cardboard or plywood under the appliance. underneath the appliance. NOTE: To avoid damaging parts, do not remove the protective shipping materials inside the appliance until the installation is complete. Unpack installation materials and accessories.
Moving the Appliance WARNING moving the appliance. To avoid product damage: Raise up via appliance rear sides. appliance upright before doing so. ance. from tipping. Special Circumstances Before proceeding with your installation, check if any of the following special circumstances apply to your installation. If so, follow the relevant instructions in the Special Installations section before continuing the installation. Frame Kit Accessory section. Side Installation section.
Product Dimensions 18" Freezer Column
24" Freezer / Refrigerator Column
30" Freezer / Refrigerator Column
Installing the Anti-tip Brackets WARNING To avoid injury or damage, check for electrical wires or plumbing in walls before drilling or installing screws. CAUTION To avoid injury, observe all safety practices during installation, including wearing safety glasses and other safety apparel.
NOTE: 2 anti-tip-brackets are required for each appliance. Anti-tip brackets (2) 1. Install the anti-tip brackets at the rear of the enclosure, locating the brackets based on stud locations and product and enclosure dimensions. 2. Make sure the anti-tip brackets are securely attached to a stud or other weight-bearing structure. uncured concrete. To ensure safety, at least one bracket must be attached to a stud. Attach brackets to studs wherever screws or bolts to attach each bracket.
Installing Appliance in Enclosure WARNING Use 2 or more people when installing the appliance. Take care when moving the appliance. It is very heavy and prone to tipping when not secured. CAUTION Take care to avoid damaging the water line or power cord when moving the appliance into the enclosure. Use an appliance dolly to move the unit near the opening. placement. Once the unit is placed in front of the opening, completely retract the front leveling legs to allow the unit to be rolled into position.
Aligning and Leveling the Appliance DEPTH ADJUSTMENT Adjust the depth of the unit in the enclosure so the door 1. Measure the thickness of your decorative door panels using the gauge tool. Measure panel thickness on the gauge tool that matches the thickness of the door panel. 2. Use the mark on the gauge tool to adjust the depth of the appliance in the enclosure. appliance at the side of the enclosure. The marked notch on the gauge tool should align with the front edge of the enclosure.
WARNING LEVELING Once the appliance is aligned properly in the enclosure, level it using the front and rear leveling legs. Leveling 2. Turn the screws as shown above to raise the appliance. Turn the screws in the opposite direction to lower the appliance. 3. Make sure the weight of the refrigerator is carried on the legs, not the wheels. CAUTION - If using a power drill, use the lowest torque setting.
Attaching Appliance to Enclosure WARNING top of the enclosure. 1. Screw the lugs on the safety bracket at the top of the appliance to the top of the enclosure. 2. If there is a large gap between the top of the appliance and the top of the enclosure, insert a piece of wood gap. enclosure. NOTE: If installing two appliances side-by-side, attach the appliances to each other using the enclosure as if they were one unit. at the top of the appliance until it engages with the top safety bracket.
Attaching the Toe Kick Panel CAUTION To avoid damage to the appliance, do not block the ventilation slots in the base panel. Stainless Toe Kick Panel (Optional Accessory) 1. Screw the base panel to the appliance. provided magnetic strips. toe kick panel. 4. Attach the stainless toe kick panel to the base panel using the magnetic strips. Wood Toe Kick Panel 2. Screw the base panel to the appliance. provided magnetic strips. 4. Stick the magnetic strips to the back of the wood toe kick panel.
Loading the Appliance Door For precise results, before attaching the door panels, load the door bins with weights to ensure the gap width remains correct after food is stored in the door.
Installing Door Panels dimensions. upper then lower drawer panel, if needed. surface. 2. Locate the correct side of the door panel template for top and left sides of the panel. on the back of the panel. and right sides of the panel. on the back of the panel. (4 mm) proud of the panel. These will be the support screws during the panel installation. 7. Insert the support screws in the slotted holes on the appliance door mounting brackets so that the panel is hanging on the door.
Adjusting Door Panels Fine adjustments can now be made to align the door panels. 1. To adjust the door panel horizontally, slide the panel support screws left or right in the slotted holes as while you tighten the support screws and insert and tighten all remaining mounting screws. 2. To adjust the door panel vertically or back and forward, loosen the screws in the appliance door bracket. Move an assistant hold the bracket in place while you tighten all the bracket screws.
Attaching Air Separator Assemble A with B and attach on bottom front center of door. Special Installations Optional Frame Kit Accessory stainless trim pieces to cover the front edges inside the enclosure. See detailed installation instructions with the kit.
Adjusting the Door Spring Rotate the adjusting screw with the T20 bit provided. I = maximum spring tension 0 = no spring tension (Optional) After adjusting the door spring, attach the gray plastic sheets to hide the adjusting screws. Adjusting the Door Stop The default door stop position is 115°. Follow these instructions to change the door stop position to 90°. 1. Open the door to 90°. 2. Insert the door stop pin in the holes which are rubber mallet to fully insert the pin.
Reversing the Door WARNING Risk of Injury Before working on the hinge, release the tension on the hinge spring. NOTE: the door MUST be supported while removing or installing mounting bolts. 1. Open the door and release the tension on the hinge spring by using the T20 bit provided to turn the screw from | to O. 2. If the air separator is attached, remove it. Remove the 2 mounting bolts at the top and bottom of the door (1). Remove the door (2) and lay it aside on a protected surface.
6. Unscrew and remove the vent cover assembly at the bottom of the appliance. 7. Follow the diagrams below to disassemble and reassemble the vent grille. Screw the vent cover assembly back onto the appliance. 8. Remove the lower hinge socket. Install the hinge socket provided in the installation accessories on the opposite side. Keep all parts in case door is reversed in future.
and install the bracket on the opposite side of the door. Repeat with the bottom hinge bracket. 10. Rotate the front cover 180 degrees and reinstall it at the top of the cabinet. 11. Install the hinge removed from the top of the cabinet on the opposite side at the bottom of the cabinet. Install the hinge removed from the bottom of the cabinet on the opposite side at the top of the cabinet. 12. Insert 2 bolts at the top and bottom of the door to reattach the door.
Side-by-Side Flush Installation FLUSH INSTALLATION CLEARANCES NOTE: When installing products with a partition between them, follow the standard installation. The NOTE: When installing 2 side-by-side products with clearance is required between the products. installations. must be used to seal the appliances together. The kit contains a sealing mat which helps prevent condensation from forming between the two appliances. accessories are missing. sealing strip (both sides) 4.
the two appliances together by installing connection brackets between the two appliances at top and bottom. 6. Insert the provided pin into both cover rails at the top of the combined units. NOTE: of both cover rails.
Preparing to Connect the Water Line NOTE: and property damage. Install the water line. Always observe the indicated dimensions to prevent damage to the water line when pushing in the appliance Connecting Water Line NOTE: When bending the water line, do not kink it, otherwise there is a risk of leaks and water damage. 1. Remove the cap from the appliance connection (1.). 2. Bend the water line according to the location of the connection on the appliance (2.). Tighten hand-tight.
Attaching the Badge layouts below.
