Specs

Page 3 of 6 | Eective 2/19
24" (610 mm)
finished width
CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES
SKSCR2401P
24" INTEGRATED
REFRIGERATOR COLUMN
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
5"
(127 mm)
electrical
location
1 3/8"
(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
23 3/4"
(603 mm)
24" (610 mm)
24"
(610 mm)
11 3/8"*
(288 mm)
26 1/4"
(666 mm)
25" (635 mm)
min. depth
flush install
24"
(610 mm)
min. depth
proud install
84"
(2134 mm)
CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION
Notes
Wine refrigerator can be installed ush or proud with 3/4"
custom panel or optional stainless steel panel kit.
Flush – With a 25" (635 mm) cutout depth, the front face
of the wine refrigerator ts ush with 25" (635 mm) depth
adjacent cabinets.
Proud – With a 24" (610 mm) depth cutout, the front face of
the wine refrigerator extends approximately 3/4" (19 mm)
beyond 24" (610 mm) depth adjacent cabinets.
Electrical
A 115V, 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
SINGLE COLUMN
Notes
Door Swing Clearances – The installation must allow
for clearances to adjacent walls or cabinets. This wine
refrigerator is equipped with a 2-position door stop. The
factory-set 115° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must
be added to the dimension noted to determine the total
clearances required from adjacent cabinets or walls. This
clearance will vary depending on the custom handle used.
When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the
door handle clearance with door open 115° is 14"
(356 mm).
INSTALLATION CLEARANCES
TOP VIEW
24" (610 mm)
finished width
CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES
SKSCR2401P
24" INTEGRATED
REFRIGERATOR COLUMN
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
5"
(127 mm)
electrical
location
1 3/8"
(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
23 3/4"
(603 mm)
24" (610 mm)
24"
(610 mm)
11 3/8"*
(288 mm)
26 1/4"
(666 mm)
25" (635 mm)
min. depth
flush install
24"
(610 mm)
min. depth
proud install
84"
(2134 mm)
SKSCW241RP
24-INCH INTEGRATED COLUMN
WINE REFRIGERATOR