Specs

Page 3 of 5 | Effective 1/22 | WCAG
24" (610 mm)
finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCW241RP
24-INCH INTEGRATED COLUMN
WINE REFRIGERATOR
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1 3/8"
(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
23 3/4"
(603 mm)
24" (610 mm)
25"
(635 mm)
11 3/8"*
(288 mm)
25 1/2"
(648 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
25" (635 mm)
min. depth
84"
(2134 mm)
CUTOUT DIMENSIONS – FLUSH INSTALLATION
Notes
Wine refrigerator can be installed ush with 3/4" custom
panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the fron
t face of
the wine refrigerator ts ush with 25" (635 mm) depth
adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or cir
cuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground faul
t interrupter) is not recommended.
SINGLE COLUMN
Notes
Door Swing Clearances – The installation must allow
for clearances to adjacent walls or cabinets. This wine
refrigerator is equipped wi
th a 2-position door stop. The
factory-set 115° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must
be added to th
e dimension noted to determine the total
clearances required from adjacent cabinets or walls. This
clearance will vary depending on the custom handle used.
When using the Stainl
ess Steel Door Panel Kit w/Handle
or the Brushed Aluminum Handle (optional accessories),
the door handle clearance with door open 115° is 14"
(356 mm).
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
24" (610 mm)
finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCW241RP
24-INCH INTEGRATED COLUMN
WINE REFRIGERATOR
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1 3/8"
(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
23 3/4"
(603 mm)
24" (610 mm)
25"
(635 mm)
11 3/8"*
(288 mm)
25 1/2"
(648 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
25" (635 mm)
min. depth
84"
(2134 mm)
SKSCW241RP
24-INCH INTEGRATED COLUMN
WINE REFRIGERATOR
CUTOUT DIMENSIONS – FLUSH
INSTALLATION SINGLE COLUMN
A minimum 4" (102 mm) finished return that matches the cabinet *
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
Notes
Wine refrigerator can be installed flush with 3/4" custom
panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the
wine refrigerator fits flush with 25" (635 mm) depth
adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall. Electrical
must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
INSTALLATION CLEARANCES – FLUSH
INSTALLATION TOP VIEW
* Door handle must be
added to this dimension.
** Varies depending on the thickness
of the custom cabinet panel. The
door panels in the optional Signature
Kitchen Suite stainless steel door
panel kit are 3/4" (19 mm) thick.
Notes
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This wine
refrigerator is equipped with a 2-position door stop. The
factory-set 115° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be
added to the dimension noted to determine the total clearances
required from adjacent cabinets or walls. This clearance will
vary depending on the custom handle used. When using the
Stainless Steel Door Panel Kit w/Handle or the Brushed
Aluminum Handle (optional accessories), the door handle
clearance with door open 115° is 14" (356 mm).
Page 3 of 5