Specs
Table Of Contents
CUTOUT DIMENSIONS – FLUSH INSTALLATION
Page 3 of 5 | Eective 1/22
≥ 24"
(610 mm)
CUTOUT DIMENSIONS – FLUSH INSTALLATION
UC WINE
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSUW2401P
24-INCH BUILT-IN UNDERCOUNTER
WINE REFRIGERATOR
A minimum 4" (101 mm) finished return that matches the cabinet
exterior is recommended on all sides and at the top of the cutout
opening. The shaded area will be visible after installation.
*
23 11/16"
(602 mm)
≥ 24"
(610 mm)
≥ 34 1/2"
(876 mm)
30 5/16"
(770 mm)
4"
(101 mm)
Handle
Side
1/8"
(2.5 mm)*
min.
Hinge
Side
1/2"
(12.5 mm)*
min.
23 11/16"
(602 mm)
with panel
23 7/16"
(595 mm)
3/16"
(4 mm)**
3/16"
(4 mm)**
Top View
Door Open 90°
Top View
Door Closed
Top View
Door Open 115°
Hinge Side
1/2"
(12.5 mm)*
3/16"
(4 mm)
Door
Case
Panel
Case
Door
1/4"
(6.5 mm)
Hinge
Case
3/16"
(4 mm)
Door
Hinge
*
Right hand hinge installation shown. When reversing the door, the hinge and handle side clearances also reverse.
**
Side clearance at front panel
TOP VIEW
≥ 24"
(610 mm)
Door Swing Clearances – The installation must allow for clearances to
adjacent walls or cabinets. This wine refrigerator is equipped with a 2-position
door stop. The factory-set 115° door swing can be adjusted to 90° if clearance
to adjacent cabinets or walls is restricted.
Door Handle Clearances – The door handle depth must be added to the
dimension as noted to determine the total clearances required from adjacent
cabinets or walls. This clearance will vary depending on the custom handle
used. When using the Stainless Steel Door Panel Kit w/ Stainless Steel Handle,
the door handle clearance with door open 115° is 11 3/4" (298 mm).
Wine refrigerator can be installed ush
with 3/4" custom panel or optional
stainless steel panel kit. With a 24" (610
mm) cutout depth, the front face of the
refrigerator ts ush with 24" (610 mm)
depth adjacent cabinets. Electrical must
be installed in adjacent cabinet for ush
installation.
Electrical – A 115V, 60Hz., 15 amp power
supply is required. An individual properly
grounded branch circuit or circuit breaker
is recommended. Install a properly
grounded 3-prong electrical receptacle
recessed into the back wall or adjacent
cabinet.
Note: GFCI (ground fault circuit
interrupter) is not recommended.
≥ 24"
(610 mm)
CUTOUT DIMENSIONS – FLUSH INSTALLATION
UC WINE
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSUW2401P
24-INCH BUILT-IN UNDERCOUNTER
WINE REFRIGERATOR
A minimum 4" (101 mm) finished return that matches the cabinet
exterior is recommended on all sides and at the top of the cutout
opening. The shaded area will be visible after installation.
*
23 11/16"
(602 mm)
≥ 24"
(610 mm)
≥ 34 1/2"
(876 mm)
30 5/16"
(770 mm)
4"
(101 mm)
Handle
Side
1/8"
(2.5 mm)*
min.
Hinge
Side
1/2"
(12.5 mm)*
min.
23 11/16"
(602 mm)
with panel
23 7/16"
(595 mm)
3/16"
(4 mm)**
3/16"
(4 mm)**
Top View
Door Open 90°
Top View
Door Closed
Top View
Door Open 115°
Hinge Side
1/2"
(12.5 mm)*
3/16"
(4 mm)
Door
Case
Panel
Case
Door
1/4"
(6.5 mm)
Hinge
Case
3/16"
(4 mm)
Door
Hinge
*
Right hand hinge installation shown. When reversing the door, the hinge and handle side clearances also reverse.
**
Side clearance at front panel
TOP VIEW
≥ 24"
(610 mm)