Manual
32
MAINTENANCE
SpeedClean™ INSTRUCTION GUIDE
1. Remove oven racks and accessories from the oven.
2. Scrape off and remove any burnt-on debris with a plastic
scraper.
3. Fill a spray bottle with 1¼ cups (10 oz or 300 ml) of water
and use the spray bottle to thoroughly spray the inside
surfaces of the oven.
4. Use at least ¼ cup (2oz or 50 ml) of the water to com-
pletely saturate the soil on both the walls and in the
corners of the oven.
5. Spray or pour the remaining 1 cup (8 oz or 250 ml) of
water onto the bottom center of the oven cavity. The
indentation on the oven bottom should be fully covered
to submerge all soils. Add water if necessary.
6. Close the oven door.
Turn the upper or lower Oven Mode knob to select the
SpeedClean™ mode.
Press START.
7. A tone will sound at the end of the 10-minute cycle.
adjust the UPPER or LOWER Oven Mode knob to OFF
position to clear the display and end the tone.
8. After the cleaning cycle and during hand-cleaning,
enough water should remain on the oven bottom to
completely submerge all soils. Add water if necessary.
Place a towel on the floor in front of the oven to capture
any water that may spill out during hand-cleaning. If you
are cleaning the upper oven on a double oven, it is also
best to cover the holes in the top of the lower oven door
with a towel to capture any water that may drip into the
door during hand-cleaning.
9. Clean the oven cavity immediately after the
SpeedClean™ cycle by scrubbing with a wet, non-scratch
scouring sponge or pad. (The scouring side will not
scratch the finish.) Some water may spill into the bottom
vents while cleaning, but it will be
captured in a pan under the oven
cavity and will not hurt the burner.
10. Once the oven cavity is cleaned, wipe any excess water
with a clean dry towel. Replace racks and any other ac-
cessories.
11. If some light soils remain, repeat the above steps,
making sure to thoroughly soak the soiled areas. If
stubborn soils remain after multiple SpeedClean™
cycles, run the Self Clean cycle. Be sure that the oven
cavity is empty of oven racks and other accessories, and
that the oven cavity surface is dry before running the
Self Clean cycle. Consult the Self Clean section of your
owner’s manual for further details.
y
Some surfaces may be hot after the SpeedClean™
cycle.Wear rubber gloves while cleaning to prevent
burns.
y
During the SpeedClean™ cycle, the oven bottom be-
comes hot enough to cause burns. Wait until the cycle
is over before wiping the inside surface of the oven.
Failure to do so may result in burns.
y
Avoid leaning or resting on the oven door glass while
cleaning the oven cavity.
CAUTION
NOTE
Use the "mist" setting on the spray bottle for better
coverage. The entire 1¼ cup (10oz or 300 ml) of water
should be used for each oven cavity cleaned.
Do not spray water directly on the door. Doing so will
result in water dripping to the floor.
NOTE
y
If you forget to saturate the inside of the oven with
water before starting SpeedClean™, turn the upper or
lower Oven Mode knob to the OFF position to end the
cycle. Wait for the oven to cool to room temperature
and then spray or pour water into the oven and start
another SpeedClean™ cycle.
y
The cavity gasket may be wet when the SpeedClean™
cycle finishes. This is normal. Do not clean the gasket.
y
If mineral deposits remain on the oven bottom after
cleaning, use a cloth or sponge soaked in vinegar to
remove them.
Suggested plastic scrapers:
•Hard plastic spatula
•Plastic pan scraper
•Plastic paint scraper
•Old credit card
NOTE
DO NOT use any steel scouring pads, abrasive pads or
cleaners as these materials can permanently damage the
oven surface.