Instruction Manual

ManualsBrandssignify ManualsMicro Lightsignify TruGroove Recessed Micro Light

Rev B. www.ledalite.compage6/9/2022 1

Linear

ID-23 T-Grid Ceiling PoE

TruGroove Recessed Micro

Installation Instructions

Standalone or Continuous Run in T-Grid Ceiling

ATTENTION: Install in accordance with local and national building and electric codes.

These instructions review how to install TruGroove recessed micro fixtures in T-Grid ceilings for power over ethernet application. For continuous

run lengths, Please refer to layout drawings supplied by Philips Ledalite in conjunction with these installation instructions. The graphics below show

the components required to install a run of TruGroove fixtures in T-Grid ceilings.

Exterior lens kits -variable lengths

Module 2

Module 1

• Bracket (x4)

• Screws (x8)

NOTE:

One kit required

for each module.

Hanger Kit(s)

Joint Kit(s)

• Joiner Aligners (x2)

• Joining Brackets (x2)

• Hex Bolts (x4)

• Screw(s)

( x1 symmetric, x2 for asymmetric )

• LED pan connectors (x1)

NOTE: Image shown is a symmetric

connector. Asymmetric has two pieces.

NOTE: One (1) kit required for each module

joint in continuous runs

Summary of content (6 pages)

PAGE 1
Linear TruGroove Recessed Micro ID-23 T-Grid Ceiling PoE Installation Instructions Standalone or Continuous Run in T-Grid Ceiling These instructions review how to install TruGroove recessed micro fixtures in T-Grid ceilings for power over ethernet application. For continuous run lengths, Please refer to layout drawings supplied by Philips Ledalite in conjunction with these installation instructions. The graphics below show the components required to install a run of TruGroove fixtures in T-Grid ceilings.
PAGE 2
ID-23 TruGroove Recessed Micro T-Grid Installation Instructions This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interreference when the equipment is operated in a commercial environment.
PAGE 3
ID-23 TruGroove Recessed Micro T-Grid Installation Instructions NOTE: For Standalone fixtures skip to step 7 4 Install Joiner Aligners 5 Open Slots for Joiner Brackets 6 Install Joiner Brackets Dimple engaged. In the joining fixtures install the joiner aligners in the trim extrusion to approximately halfway Important: To insert aligners, tap gently with a hammer until half is inserted into the joiner channel. Be sure to engage the dimple.
PAGE 4
ID-23 10a TruGroove Recessed Micro T-Grid Installation Instructions LED Pan Joiner - Symmetric Mount the LED pan connector with the supplied screw in the joiner kit. 11 10b LED Pan Joiner - Asymmetric Mount the LED Pan connector with the supplied screw in the joiner kit. There are two pieces for asymmetric fixtures. Install Snap-In Flush Lens Standalone Units: Lenses are supplied in 2’, 3’, 4’, 5’, 6’ or 8’ lengths.
PAGE 5
ID-23 TruGroove Recessed Micro T-Grid Installation Instructions Sensors in Rows Single Sensor Controlling Whole Row 1. Purple & brown (or purple & grey/pink) control wires MUST be connected between fixtures. Note: • A maximum of 8 drivers can be wired to one sensor; confirm fixture driver count with factory. 1 Integral Sensor Alternate Remote Sensor Bottom view of fixtures 4ft 8ft Multiple Sensors Controlling Separate Zones in a Row 2.
PAGE 6
ID-23 TruGroove Recessed Micro T-Grid Installation Instructions Occupancy Sensor Coverage: Note: Longer dimension of detection area (Y1, Y2) is parallel to longer dimension of the luminaire. The detection area for the movement sensor can be roughly divided into two parts: • Minor movement (person moving ≤3ft/s or 0.9m/s). • Major movement (person moving ≥3ft/s or 0.9m/s).