SIIG 2S1P Combo-Value Quick Installation Guide Introducing the SIIG 2S1P Combo-Value The SIIG 2S1P Combo-Value is a total solution for serial and parallel device connections. It provides two 16550 UART serial ports which supports data transfer rates up to 115Kbps and one ECP/EPP parallel port which supports data transfer rates up to 1.5 MB/sec. Features and Benefits • • • • Conforms to PCI v2.2 Plug and Play Can be installed in 32-/64-bit, 3.
System Requirements • • Pentium® or equivalent computer with an available PCI slot DOS, Windows® 95/98/98SE/ME/NT 4.0/2000/ XP (32-/64-bit)/Server 2003/Vista (32-/64-bit) Package Contents • • • • SIIG 2S1P Combo Value board DB9 (9-pin) serial port cable (for 2nd serial port) Driver CD Quick installation guide Layout Serial Port 2 (S2) Serial Port 1 (S1) Parallel Port Figure 1.
Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges. 1. 2. 3. 4. 5. 6. 7. 8.
Driver Installation This section provides information on how to install the SIIG 2S1P Combo Value drivers. Please make sure the board is installed before proceeding. Windows 95 1. 2. 3. 4. 5. At the Update Device Driver Wizard, click Next. Insert the driver CD and click Other Locations. Type in X:\2S1P\95, click OK, then click Finish. (Change X: to match your CD-ROM drive letter) From the Insert Disk window, click OK. When the Copying Files dialog box appears, type in X:\95, then click OK.
2. 3. 4. Check Specify a location, uncheck the other box, insert the driver CD, type in X:\2S1P\ME, then click Next. (Change X: to match your CD-ROM drive letter) Click Next, then click Finish. Restart Windows to complete the installation. Windows NT 4.0 1 2. 3. 4. 5. From the desktop, click Start, then Run. Insert the driver CD, type X:\2S1P\NT\Setup_Combo.exe, then click OK. (Change X: to match your CD-ROM drive letter) At the Welcome window, click Continue.
Windows XP 1. 2. 3. 4. 5. At the Found New Hardware Wizard, For XP SP1 or earlier: Select Install from a list or specific location (Advanced), then click Next. For XP SP2 or later: Select No, not this time, click Next. Select Install from a list or specific location (Advanced), then click Next. Insert the driver CD, check Include this location in the search, uncheck the other box, type in X:\2S1P\XP, then click Next.
Windows Server 2003 1. 2. 3. 4. 5. At the Found New Hardware Wizard, For Server 2003: Select Install from a list or specific location (Advanced), then click Next. For Server 2003 SP1 or later: Select No, not this time, click Next. Select Install from a list or specific location (Advanced), then click Next. Insert the driver CD, check Include this location in the search, uncheck the other box, type in X:\2S1P\2003, then click Next.
Windows Vista ™ 1. 2. 3. At the Found New Hardware window, click Locate and install driver software (recommended), click Continue. When prompted, insert the driver CD and the driver will install automatically. At The software for this device has been successfully installed window, click Close to complete the installation. Note: Driver installation may take several minutes to complete. If your internet connection is enabled, the driver may install automatically via Windows Update.
Verify Windows Installation Windows 95/98/98SE/ME 1. 2. 3. Right click My Computer, click Properties, click Device Manager. Double click Multi-function adapters or NetMos MultiFunction, NetMos PCI... Controller should be listed. Double click Ports (COM & LPT), two NetMos PCI Serial Ports and one NetMos PCI Parallel Port should be listed. Windows NT 4.0 1. 2. 3. Click Start, Settings, Control Panel.
Windows XP (64-bit)/Server 2003 1. 2. 3. Right click My Computer, click Manage, then click Device Manger. Double click Multifunction adapters, MosChip... Controller should be listed. Double click Ports (COM & LPT), two MosChip Serial Ports and one MosChip... Parallel Port should be listed. Windows Vista 1. 2. 3. 10 Right click Computer, click Manage, click Continue then click Device Manger. Double click Multifunction adapters, MosChip... Controller should be listed.
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a 2-year manufacturer warranty with this product. Please see our web site for more warranty details.
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty.
