A/V PowerSaver 8 Quick Installation Guide Introducing the A/V PowerSaver 8 The A/V PowerSaver 8 surge protector provides a great energy conservation solution that utilizes the MasterPower-Save control concept.
Layout Power Cord Resettable Circuit Breaker Surge Protection LED Grounding LED Auto /Manual Switch Master Outlet (1) with LED Network (RJ45) Jacks Power Save Outlets (5) with LED Always On Outlets (2) with LED Phone (RJ11) Jacks DSS/Coax Connector for Surge Protection Figure 1: Layout • • • • 2 Power Cord: Long 6 foot heavy-duty power cord with low-profile plug (does not block furniture from sitting close to the wall) Resettable Circuit Breaker (15A): Protects against current overload Surge Prote
• • • • • • • Master Outlet (1) with LED: Main outlet – controls the “ON/OFF” status of the “POWER SAVER” outlets Power Save Outlets (5) with LED: Power saving outlets- power automatically turns ON/OFF according to Master Outlet’s device status.
Using Power Save Feature To enable the Power Save feature, select the AUTO setting on the AUTO/Manual switch. Note: The MANUAL setting will convert all outlets to “Always On” functionality. Plug your TV, computer, or other “MASTER” device into the “MASTER” outlet and plug peripherals (DVD player, A/V receiver, CD player, printer, etc.) into the “POWER SAVE” outlets.
-year Limited Warranty and Connected Equipment Guarantee In purchasing a SIIG A/V PowerSaver8 surge protector in the United States or Canada, the original end user receives a Limited Warranty and Connected Equipment Guarantee from SIIG, Inc. (for ease of reading, referred to as “SIIG”). The Limited Warranty and the Connected Equipment Guarantee are intended to be the original end-user’s exclusive rights and remedies.
Equipment Guarantee or the State or Province may impose additional obligations, or additional “implied warranties.” To the extent necessary to comply with those laws, the terms of the Limited Warranty and the Connected Equipment Guarantee should be read to adjust to those requirements only to the extent necessary to comply with such local law. If you are an Initial Customer, you are asked to read the following terms and conditions carefully before using the Product.
IMPLIED WARRANTY OF MERCHANTABILITY ORFOR FITNESS FOR A PARTICULAR PURPOSE, IF APPLICABLE TO THE PRODUCT, IS LIMITED IN DURATION TO THE PERIOD OF OWNERSHIP BY THE INITIAL CUSTOMER. THIS PROVISION SHALL NOT CREATE ANY IMPLIED WARRANTY OR MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE THAT WOULD NOT OTHERWISE APPLY TO THE PRODUCT. NOTE: SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
Initial Customer (the original end-user consumer purchaser) of the Product. 2. A) If it is within the store's return policy period, please return the product to the store where you purchased from. B) If your purchase has passed the store's return policy period, please follow these steps to have the product repaired or replaced. Step 1: Submit your RMA request. Go to www.siig.com, click Support, then RMA to submit a request to SIIG RMA..
SIIG will inspect and examine the Product within ten (10) days of receipt. If the Product is not as warranted, SIIG will repair or replace the Product and return it to you at SIIG’s expense, or, if SIIG is unable to or decides not to repair or replace the Product (if defective) within a reasonable time, SIIG will refund to you the full purchase price you paid for the Product (purchase receipt showing price paid is required).
The Limited Warranty does not cover Connected Equipment, but as is explained below, to be covered under the Connected Equipment Guarantee, the Connected Equipment must have been damaged due only to a direct failure of the Product. The Connected Equipment must have been damaged due to only a defect in materials or workmanship of the Product. In the event of damage to the Connected Equipment, your exclusive remedies, and SIIG’s sole obligations, are as follows for Connected Equipment.
Making a Connected Equipment Guarantee Claim. To make a Warranty claim for damage to Connected Equipment under the Connected Equipment Guarantee, you must do the following: 1. Complete and return the SIIG Warranty card or provide reasonable proof of purchase, for example, a sales receipt that establishes you as the original end-user consumer purchaser of the Product. 2. Go to www.siig.
SIIG’s Duties. SIIG will inspect and examine the Product and the item(s) of Connected Equipment (or at SIIG’s election, your written statement and repair cost estimate for those item(s)). You must return the product for inspection.
such equipment so that SIIG’s maximum liability shall be reduced to reflect all such other payments or sources of recovery. If SIIG replaces the connected equipment or pays to the Initial Customer the Agreed Damage Amount, the Initial Customer shall transfer ownership of all item(s) to SIIG without warranty by the Initial Customer, but free of lien or other interest.
3. Guarantee to Connected Equipment (and only up to the applicable aggregate ceiling amount). The Connected Equipment Guarantee does not cover damage to Connected Equipment or apply if the Product has been operated in a failure mode or not in compliance with SIIG operating instructions and manuals, or if the Connected Equipment has been operated in a failure mode or not in compliance with the instructions and manuals of its manufacturer/vendor.
SIIG Does Not Cover or Undertake Any Liability in Any Event for Any of the Following: 1. Loss of or damage to all electronic data, records, software applications or software programs or the restoration of electronic data, records, or the reinstallation of any software. 2.
WHETHER FOR DAMAGE TO OR LOSS OF PROPERTY [EXCEPT FOR (AND ONLY FOR) THE SPECIFIC LIMITED AGREEMENT OF SIIG TO PROVIDE CERTAIN WARRANTY BENEFITS REGARDING “CONNECTED EQUIPMENT” UNDER THE “SIIG CONNECTED EQUIPMENT GUARANTEE”], LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION OR DATA. NOTE: SOME STATES OR PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE SIIG PRODUCT. The Limited Warranty and the Connected Equipment Guarantee are governed by the laws of the United States and the State of California, without reference to conflict of law principles. The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded. Contact Information: SIIG’s address is 6078 Stewart Ave., Fremont, CA 94538 and its phone number is (510) 6578688.
Blank Page 18
Blank Page 19
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty.
