A/V PowerSaver Pro Quick Installation Guide Introducing the A/V PowerSaver Pro The A/V PowerSaver Pro is an energy conserving device that automatically detects power consumption and turns off connected electrical appliances to save standby power consumption.
Layout Front Panel Features • • • • • • AC Power LED: LED indicator light shows that power is being supplied to the Power Save (Switched) outlets.
Rear Panel Features • • • • DSS/Coax Connectors: Provides protection from surges on cable, DSS and cable modem installations Always On (Unswitched) Outlets: 3 outlets with LED (green) that supply constant power Power Save (Switched) Outlets: Power saving outlets that are automatically controlled by power management system Power Cord: Low profile plug with 90 degree rotating cord, does not block funiture from sitting close to the wall and offers flexible positioning of unit/power cable DSS/Coax Connectors
Right and Left Panel Features • • • Reset: Circuit Breaker (15A) - Protects against current overload automatically opens when the current load is greater the 15 Amps. Push to manually reset.
3. Connect the external IR remote extender cable into the connector. This accessory is not included and must be purchased separately. Note: This optional accessory extends the IR transmission distance. Operation 1. 2. Plug the power cord into a reliable power source. The Main Display LED flashes once and the LEDs for surge protection, grounding and always on are lit. Note: At this moment only the Always On outlets are receiving power, the Power Save (Switched) outlets are still off (power saving mode).
4. Turn on an appliance connected to the Power Save (Switched) outlets. Note: The display will show the cumulative power consumption of the Power Save outlets only. 5. The A/V PowerSaver Pro will automatically detect variations of total power consumption and if the total power consumption lowers by over 70% for 3 consecutive minutes the Power Save (Switched) outlets will be turned off and the A/V PowerSaver Pro will be placed into standby mode.
5-year Limited Warranty and Connected Equipment Guarantee In purchasing a SIIG A/V PowerSaver Pro surge protector in the United States or Canada, the original end user receives a Limited Warranty and Connected Equipment Guarantee from SIIG, Inc. (for ease of reading, referred to as “SIIG”). The Limited Warranty and the Connected Equipment Guarantee are intended to be the original end-user’s exclusive rights and remedies.
additional obligations, or additional “implied warranties.” To the extent necessary to comply with those laws, the terms of the Limited Warranty and the Connected Equipment Guarantee should be read to adjust to those requirements only to the extent necessary to comply with such local law. If you are an Initial Customer, you are asked to read the following terms and conditions carefully before using the Product.
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FOR FITNESS FOR A PARTICULAR PURPOSE, IF APPLICABLE TO THE PRODUCT, IS LIMITED IN DURATION TO THE PERIOD OF OWNERSHIP BY THE INITIAL CUSTOMER. THIS PROVISION SHALL NOT CREATE ANY IMPLIED WARRANTY OR MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE THAT WOULD NOT OTHERWISE APPLY TO THE PRODUCT. NOTE: SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
Making a Limited Warranty Claim To make a Limited Warranty claim on a Product, you must do the following: 1. Complete and return the SIIG Warranty Registration Card, or provide reasonable proof of purchase (for example, a sales receipt) that establishes you as the Initial Customer (the original end-user consumer purchaser) of the Product. 2. A) If it is within the store's return policy period, please return the product to the store where you purchased from.
• You are responsible for the cost of shipping. Ship the product to the following address: SIIG, Inc. 6078 Stewart Avenue Fremont, CA 94538-3152, USA RMA #: • SIIG will ship the repaired or replaced product via Ground in the U.S. and International Economy outside of the U.S. at no cost to the customer. SIIG will inspect and examine the Product within ten (10) days of receipt.
The Connected Equipment Guarantee is not “first dollar” coverage. It is secondary. If you have any other source of payment for your loss, such as insurance, another warranty, or an extended warranty or purchase protection plan (“Primary Coverage”), SIIG’ will pay only to the extent that that the Primary Coverage does not cover the loss.
spikes on standard telephone equipment lines, or Base 10/100T Ethernet lines that are properly installed and connected (a “Power Disturbance”) and (y) is directly plugged into and properly connected to a SIIG Product in its original condition which is properly operated when a Power Disturbance passes through the SIIG Product and (z.1) exhausts the protection capacity of the SIIG Product or (z.2) damages the SIIG Product.
and all claim forms that SIIG provides to you. Show the Claim Number on the shipping label or include it with the product. Initial Customer shall prepay all shipping costs, must pay the cost of the repair estimate, and is responsible for packaging and shipment. 5. Permit SIIG or its agents to make an onsite inspection of the Product, Connected Equipment, and electrical system at your location.
2. The aggregate ceiling amount for all claims by an Initial Customer for Connected Equipment: SIIG A/V PowerSaver Pro - $250,000.00. 3. The amount(s) of all payment you have or are entitled to receive from insurance, other warranties, extended warranties, or from other sources or persons for the Connected Equipment or damage to such equipment so that SIIG’s maximum liability shall be reduced to reflect all such other payments or sources of recovery.
in transit, in shipment, or in storage, damage or deterioration, improper operation or maintenance, or use with items or equipment not designed or intended for use with the product. 2. As to Connected Equipment, the Connected Equipment Guarantee covers only damage within the specific terms of the Connected Equipment Guarantee to Connected Equipment (and only up to the applicable aggregate ceiling amount). 3.
5. Has backed up all software on Connected Equipment on a consistent basis. 6. Has not used the Product with more than one computer, one printer, and one monitor/screen at the same time. SIIG Does Not Cover or Undertake Any Liability in Any Event for Any of the Following: 1. Loss of or damage to all electronic data, records, software applications or software programs or the restoration of electronic data, records, or the reinstallation of any software. 2.
Exclusion of Consequential and Other Damages THE SOLE AND EXCLUSIVE REMEDIES OF THE INITIAL CUSTOMER ARE THOSE PROVIDED BY THE LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE. SIIG EXCLUDES ANY LIABILITY FOR PERSONAL INJURY AND PROPERTY DAMAGE UNDER THE LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE.
severe physical or property damage, or that would affect operation or safety of any medical or life support device (collectively, “High Risk Activities”). SIIG expressly disclaims any express or implied warranty of fitness for High Risk Activities. SIIG does not authorize use of its Product in any High Risk Activities. ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE SIIG PRODUCT.
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCIe, PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty.
