Installation guide

ManualsBrandsSIIG Manualscomputer componentsJJ-E20011-S1

CyberSerial Dual PCIe

Quick Installation Guide

04-0611A

Introducing the CyberSerial Dual PCIe

The CyberSerial Dual PCIe high-speed serial I/O card

provides two additional 9-pin serial ports.

Features and Benefits

• Compliant with PCI Express Base Specification 1.0a

• PCI Express 1-lane (x1) serial I/O card works with

PCI Express slots with different lane width

• Installs into any available PCI Express slot and

provides two 9-pin RS232 serial ports

• 128-byte FIFO buffers dramatically increase data

transmit/receive speed and supports data rates up

to 920 Kbps

• Works as standard RS232 port or with 5V or 12V

power output for devices that require power

System Requirements

• PCI Express-enabled system with an available PCI

Express slot

• Windows 7 (32-/64-bit) / Vista (32-/64-bit) / XP

(32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / 2000

Package Contents

• CyberSerial Dual PCIe adapter and spare enhanced

low profile bracket

• Mini 2-port fan-out cable

• "Y" split power cable

• Driver CD & quick installation guide

Summary of content (12 pages)

PAGE 1
CyberSerial Dual PCIe Quick Installation Guide Introducing the CyberSerial Dual PCIe The CyberSerial Dual PCIe high-speed serial I/O card provides two additional 9-pin serial ports. Features and Benefits • • • • • Compliant with PCI Express Base Specification 1.
PAGE 2
Layout J1 Power connector* J2 Fan-out cable connector Figure 1: Layout * Note: If the serial port requires power output, connect the system power source to board's power connector. However, most serial devices do not require additional power through the serial port. Refer to your serial device's manual for more information.
PAGE 3
Mini 2-port fan-out cable Board connector 9-pin serial Figure 2: Mini 2-port fan-out cable Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds.
PAGE 4
. 5. 7. 8. 9. Set J1 and J2 jumper settings to the desired voltage only if your serial device needs additional power from the serial port. However, most serial devices do not require additional power. If power output is required, connect the board's power connector to the system power supply. For more information see Jumper Settings on page 2. To install the card, carefully align the card's bus connector with the selected PCI Express slot on the motherboard.
PAGE 5
6. 7. 8. 9. 10. Under Other Devices, starting at the top, right click 16C95X Serial Port, then click Update Driver Software. Click Browse my computer for driver software. Type D:, click Next. (Change D: to match your CD/ DVD-ROM drive letter) At Windows has successfully updated your driver software, click Close. Repeat steps 6-9 to complete the installation. Windows Vista (32-/64-bit) 1. 2. 3. 4.
PAGE 6
3. Insert the driver CD, check Include this location in the search, uncheck the other box. Note: Click Cancel at the CD AutoPlay box if prompted. 4. 5. For 32-bit: Type D:\XP-Later\32-bit, and click Next, then click Finish. (Change D: to match your CDROM drive letter) For 64-bit: Type D:\XP-Later\64-bit, and click Next, click Continue Anyway, then click Finish. (Change D: to match your CD-ROM drive letter) Repeat steps 1-3 one or two times. Click Yes to restart Winodows to complete the installation.
PAGE 7
Windows 2000 1. 2. 3. 4. 5. 6. At the Found New Hardware Wizard, click Next. Select Search for a suitable driver for my device (recommended), and click Next. Check Specify a location, uncheck the other boxes, then click Next. Insert the driver CD, type in D:\2K, then click OK. (Change D: to match your CD/DVD-ROM drive letter) Click Next and Finish. Repeat steps 1-5 to complete the installation. To Verify Windows Installation 1. 2. 3. Check in Device Manager to verify successful driver installation.
PAGE 8
Changing COM Port Number Some serial devices need a specific COM port in order to work. If your serial device works properly, do not change this setting. 1. 2. 3. 4. 8 From the Device Manager window double click Ports (COM & LPT), then double click the CyberSerial serial port you want to change. Click Settings tab. Click the down arrow that is next to the COM Port number box, select a COM port that is not in use, then click OK. Click OK, then close Device Manager to save the changes.
PAGE 9
Blank Page 9
PAGE 10
Blank Page 10
PAGE 11
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a lifetime manufacturer warranty with this product. Please see our web site for more warranty details.
PAGE 12
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio.