Installation guide

ManualsBrandsSIIG Manualscomputer componentsJU-2NG012

USB 2.0+FireWire+10/100/1000

Quick Installation Guide

04-0310A

Features and Benefits

• Combo card design adds USB 2.0 (480 Mbps),

FireWire (400 Mbps), Gigabit (10/100/1000 Mbps)

Ethernet interface to your computer at once.

• Fully compliant with PCI specification 2.2

• Hot-swapping feature allows you to connect/

disconnect USB and 1394 devices without powering

down your system

USB 2.0 interface:

• Adds two external and one internal USB 2.0 ports

• Compliant with USB specification rev. 2.0

• Supports high-speed (480 Mbps), full-speed (12

Mbps), and low-speed (1.5 Mbps) data transfer

modes for simultaneous operation of multiple USB

2.0/1.1 devices

NOTE: USB 1.1 devices are limited to USB 1.1

speeds even when they are connected to USB 2.0

host adapter or USB 2.0 hubs.

FireWire (1394a) interface:

• Adds two external and one internal FireWire ports

• Compliant with IEEE 1394-1995, P1394a-2000 and

OHCI 1.1 standards

• Supports serial bus data transfer rates of 100, 200

and 400 Mbps

Summary of content (12 pages)

PAGE 1
USB 2.0+FireWire+10/100/1000 Quick Installation Guide Features and Benefits • • • Combo card design adds USB 2.0 (480 Mbps), FireWire (400 Mbps), Gigabit (10/100/1000 Mbps) Ethernet interface to your computer at once. Fully compliant with PCI specification 2.2 Hot-swapping feature allows you to connect/ disconnect USB and 1394 devices without powering down your system USB 2.0 interface: • Adds two external and one internal USB 2.0 ports • Compliant with USB specification rev. 2.
PAGE 2
Gigabit (10/100/1000 Mbps) Ethernet interface: • Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab • Supports Full Duplex Flow Control (IEEE 802.3x) • Integrated 10/100/1000 transceiver • Auto-Negotiation with Next page capability • Supports pair swap/polarity/skew correction • Crossover Detection & Auto-Correction • Transmit/Receive FIFO (8K/64K) support • Supports IEEE 802.
PAGE 3
Layout FireWire (1394a) Wake-On-LAN (optional)* USB 2.0 Gigabit Ethernet Power Connector (Optional)** Figure 1. Board Layout *NOTE: The Wake-On-LAN (WOL) feature is optional and not needed in many cases. If you want to use this feature, the system's motherboard has to have a 3-pin WOL connector onboard. Follow the directions below to enable this feature. 1. Connect one end of the WOL cable to the board's WOL connector. 2. Connect the other end of the WOL cable to the motherboard's WOL connector. 3.
PAGE 4
1) Hardware Installation General instructions for installing the card are provided below, since the design of computer cases and motherboards vary. Refer to your computer’s reference manual for further information, if needed. 1. Turn OFF the power to your computer. 2. Unplug the power cord and remove your computer's cover. 3. Remove the slot bracket from an available PCI slot. 4. Carefully align the card to the selected PCI slot push the board down firmly, but gently, until it is well seated. 5.
PAGE 5
2) Software Installation To ensure proper installation of this board, please follow these instructions step-by-step. 2-1) Windows 98SE Driver Installation 1. Install the board, boot up your system, and insert the driver CD. 2. At the Add New Hardware Wizard window, click Cancel. 3. Click Start, Run, type in X:\setup.exe, then click OK. (Change X: to match your CD-ROM drive letter) 4. Choose Yes, I want to restart my computer now, then click Close to restart Windows. 5.
PAGE 6
15. Choose Search for the best driver..., then click Next. 16. Clear all boxes, then click Next. 17. Choose The updated driver (Recommended), then click Next. 18. Click Next, then Finish. 19. Repeat steps 14-18 two more times. 20. Click Yes to restart to complete. 2-2) Windows ME Driver Installation 1. 2. 3. 4. 5. 6. 7. 8. 6 Install the board, boot up your system, and insert the driver CD. At the Add New Hardware Wizard window, click Cancel. Click Start, Run, type in X:\setup.exe, then click OK.
PAGE 7
9. Choose The updated software (Recommended) and click Next. 10. Click Next, then Finish. 11. Click Yes to restart Windows to complete. NOTE: If prompted to restart Windows again after a restart, click Yes. 2-3) Windows 2000 Driver Installation 1. Install the board, boot up your system, and insert the driver CD. NOTE: If you have Windows 2000 with Service Pack 4 (SP 4) or later, skip to step 5. 2. At the Add New Hardware Wizard window, click Cancel two times. 3. Click Start, Run, type in X:\setup.
PAGE 8
2-4) Windows XP Driver Installation 1. Install the board, boot up your system, and insert the driver CD. NOTE: If you have Windows XP with Service Pack 1 (SP 1) or later, follow steps 7-9 only and ignore the rest. 2. At the Add New Hardware Wizard window, click Cancel two times. 3. Click Start, Run, type in X:\setup.exe, then click OK. (Change X: to match your CD-ROM drive letter) 4. Choose Yes, I want to restart my computer now, then click Close to restart Windows. 5.
PAGE 9
2-5) To verify successful driver installation: 1. Check Device Manager to verify successful driver installation. Windows 98SE/ME: From the main desktop, right click My Computer, then click Properties. Click Device Manager tab. Windows 2000/XP: Right click My Computer, then click Manage. Click Device Manager. 2. The drivers for this controller show up differently under different versions of Windows. Please refer to the correct Windows version to verify. 2-5.
PAGE 10
2-5.2) Windows 2000 (with sp3 or later)/XP (with sp1 or later): a) Under the Universal Serial Bus Controllers: - NEC PCI to USB Open Host Controller - NEC PCI to USB Open Host Controller - Standard Enhanced PCI to USB Host Controller - USB Root Hub (USB 2.
PAGE 11
Technical Support QUESTIONS? SIIG’s Online Support has the answers! Simply visit our Web site at www.siig.com and click on Support. Our online support database is updated daily with new drivers and solutions. The answers to your problems could be just a few clicks away. If you can't find answers or solutions to your questions, you have an option to submit the problems online to one of our technical support analysts and we will promptly respond to you with answers or solutions.
PAGE 12
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), Networking, Sound Cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and all products are backed by a 5-year manufacturer warranty.