Installation guide

ManualsBrandsSIIG ManualsComputersSATA/USB 2.0 Docking

Introducing the Cool SATA to USB 2.0

The Cool Dual SATA to USB 2.0 Docking is designed to

support USB equipped computers. This adapter

provides large capacity mobile storage using 2.5" or 3.5"

SATA hard disk drives through high-speed, hot-

swapping USB 2.0 interface.

Features and Benefits

• Compliant with USB 1.1 and 2.0 specifications

• Supports data transfer rate up to 480 Mb/s

• Built-in silent cooling fan effectively extends hard

disk drive life

• Dual-bay design works with 2.5- and 3.5-inch (or

mix) SATA hard disk drives

• Supports SATA 1.5/3 Gb/s hard disk drive capacity

up to 750 GB (2.5-inch) and 2 TB (3.5-inch)

• Plug and Play, no additional drivers needed

• Supports USB hot-swap and hot-plug

System Requirements

• PC or Mac

computer with an available USB port

(USB 2.0 recommended)

• Windows

7 (32-/64-bit) / Vista (32-/64-bit) / XP

(32-/64-bit) / Server 2003 & 2008 (32-/64-bit) /

2000

• Mac OS

X v10.4.8 or higher

Cool Dual SATA to

USB 2.0 Docking

Quick Installation Guide

04-0523B

Summary of content (8 pages)

PAGE 1
Cool Dual SATA to USB 2.0 Docking Quick Installation Guide Introducing the Cool SATA to USB 2.0 The Cool Dual SATA to USB 2.0 Docking is designed to support USB equipped computers. This adapter provides large capacity mobile storage using 2.5" or 3.5" SATA hard disk drives through high-speed, hotswapping USB 2.0 interface. Features and Benefits • • • • • • • Compliant with USB 1.1 and 2.
PAGE 2
Package Contents • • • • Cool Dual SATA to USB 2.0 Docking Switching power adapter USB 2.0 cable (type A to type B) & rubber pads Quick installation guide Layout SATA Drive Slot LED (Two LED's stay on while the unit is on) On/Off Switch HDD LED (One LED per HDD; LED flashes while transfering data) Figure 1. Front Layout USB Connector Power Adapter Jack Figure 2: Back Layout Note: You cannot use one hard drive in both platforms, Windows and Mac.
PAGE 3
Hardware Installation 1. 2. 3. 4. Make sure the SATA connectors of the Cool Dual SATA to USB 2.0 Docking and the SATA hard disk drive are in alignment. Carefully insert the SATA hard disk drive into the SATA drive slot. Plug the included switching power adapter into the power adapter jack ot the Cool Dual SATA to USB 2.0 Docking, then plug the switching power adapter into a reliable power source. Use the included USB 2.0 cable to plug the Cool Dual SATA to USB 2.0 Docking into the computer.
PAGE 4
Using the Cool Dual SATA to USB 2.0 Docking Windows One drive icon for each inserted hard disk drive will appear in Computer or My Computer when the Cool Dual SATA to USB 2.0 Docking is plugged into a USB port. The drive(s) act just like a conventional hard disk drive in your system. Note: Be careful not to touch the hard disk drive while in use. It will be warm. Disconnecting From The Computer Important: Do not insert or remove a hard disk drive from the Cool Dual SATA to USB 2.
PAGE 5
Windows Vista 1. Verify that the HDD LED(s) are OFF before proceeding. 2. Double click the Unplug or Eject Hardware icon located in the system tray. 3. Highlight USB Mass Storage Device, click Stop. 4. Click OK, click OK again, then Close. 5. You can now unplug or turn off the Cool Dual SATA to USB 2.0 Docking. Windows XP / Server 2003 & 2008 1. Verify that the HDD LED(s) are OFF before proceeding. 2. Double click the Safely Remove Hardware icon located in the system tray. 3.
PAGE 6
Mac One drive icon for each inserted SATA hard disk drive will appear on the desktop when the Cool Dual SATA to USB 2.0 Docking is plugged into a USB port. The drive(s) act just like a conventional hard drive in your system. Disconnecting From The Computer Before unplugging the Cool Dual SATA to USB 2.0 Docking from the computer, drag the drive icon(s) into the Trashcan and wait for the confirmation box. The same rule applies when turning off the Cool Dual SATA to USB 2.0 Docking.
PAGE 7
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a 2-year manufacturer warranty with this product. Please see our web site for more warranty details.
PAGE 8
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio.