Installation guide

ManualsBrandsSIIG ManualsComputersSC-SA0312-S1

Introducing the Cool SATA to USB 2.0

The Cool SATA to USB 2.0/eSATA Docking is designed to

support USB 2.0 and eSATA equipped computers. This

adapter provides large capacity mobile storage using

3.5" or 2.5" SATA hard disk drives through high-speed,

hot-swapping USB 2.0 & eSATA interfaces.

Features and Benefits

• Supports Hi-Speed USB 2.0 & eSATA interfaces

• Supports SATA I/II (SATA 150/300)

• Supports 2.5" and 3.5" hard drive

• Plug and Play, no additional drivers needed

• Supports USB hot-swap and hot-plug

System Requirements

PC:

• Pentium

or equivalent computer with an available

eSATA or USB port (USB 2.0 recommended)

• Windows

2000 / XP (32-/64-bit) / Server 2003 &

2008 (32-/64-bit) / Vista (32-/64-bit)

Mac

• An available eSATA or USB port (USB 2.0

recommended)

• Mac OS

X v10.4.8 or higher

Cool SATA to USB 2.0/

eSATA Docking

Quick Installation Guide

04-0522A

Summary of content (8 pages)

PAGE 1
Cool SATA to USB 2.0/ eSATA Docking Quick Installation Guide Introducing the Cool SATA to USB 2.0 The Cool SATA to USB 2.0/eSATA Docking is designed to support USB 2.0 and eSATA equipped computers. This adapter provides large capacity mobile storage using 3.5" or 2.5" SATA hard disk drives through high-speed, hot-swapping USB 2.0 & eSATA interfaces. Features and Benefits • • • • • Supports Hi-Speed USB 2.0 & eSATA interfaces Supports SATA I/II (SATA 150/300) Supports 2.5" and 3.
PAGE 2
Package Contents • • • • • Cool SATA to USB 2.0/eSATA Docking Switching power adapter USB 2.0 cable (type A to type B) eSATA cable Quick Installation Guide Layout SATA Drive Slot LED (All three LED's stay on while the unit is on) On/Off Switch LED (This LED flashes while transfering or receving data) Figure 1. Front Layout eSATA Connector USB Connector Power Adapter Jack Figure 2: Back Layout Note: You cannot use one hard drive in both platforms, Windows and Mac.
PAGE 3
Hardware Installation 1. 2. 3. Make sure the SATA connectors are in alignment. Gently insert the SATA hard drive into the SATA drive slot. Plug the included switching power adapter into the Cool SATA to USB 2.0/eSATA Docking power adapter jack, then plug the switching power adapter into a reliable power source. Use either the USB 2.0 cable OR eSATA cable to plug the Cool SATA to USB 2.0/eSATA Docking into the computer. Note: Do not connect the USB 2.0 cable and eSATA cable at the same time. 4.
PAGE 4
Using the Cool SATA to USB 2.0/eSATA Windows Two additional drive icon will appear in My Computer when the converter is plugged into a USB port. The drive acts just like a conventional hard drive in your system. Note: Be careful not to touch the hard drive while in use. It will be warm. Disconnecting from USB Before unplugging the Cool SATA to USB 2.0/eSATA Docking from the computer, it must first be stopped, by using Windows' Safely Remove Hardware utility.
PAGE 5
2. 3. Highlight USB Mass Storage Device, click Stop, OK then Close. You can now unplug or turn off the Cool SATA to USB 2.0/eSATA Docking. Windows Vista™ 1. Verify that the HDD LED is OFF before proceeding. Double click the Unplug or Eject Hardware icon located in the system tray. 2. Highlight USB Mass Storage Device, click Stop. 3. Click OK, click OK again, then Close. 4. You can now unplug or turn off the Cool SATA to USB 2.0/eSATA Docking. Disconnecting from eSATA 1. 2. 3. 4. 5.
PAGE 6
Disconnecting From The Computer Before unplugging the Cool SATA to USB 2.0/eSATA Docking from the computer, drag the drive icon into the Trashcan and wait for the confirmation box. The same rule applies when turning off theCool SATA to USB 2.0/ eSATA Docking . Not following these instructions may result in data corruption or damage to the hard drive.
PAGE 7
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a 2-year manufacturer warranty with this product. Please see our web site for more warranty details.
PAGE 8
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCIe, PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty.