TDS

ManualsBrandsSika ManualsKitchen10.1 fl. oz. AnchorFix-1 Anchoring Adhesive

PRODUCT DATA SHEET

Sika® AnchorFix-1

HIGH STRENGTH, TWO COMPONENT ADHESIVE ANCHORING SYSTEM

PRODUCT DESCRIPTION

Sika® AnchorFix-1 adhesive anchoring system has been

specially formulated as a high-performance, two com-

ponent adhesive anchor system for threaded and rein-

forcing bars in uncracked concrete.

USES

Sika® AnchorFix-1 may only be used by experienced pro-

fessionals.

As a fast curing anchoring adhesive for all grades of:

Rebars / reinforcing steel▪

Threaded rods▪

Bolts and special fastening systems▪

Can be used on:

Uncracked Concrete▪

Solid masonry▪

Hard natural stone

▪

Solid rock

▪

* These substrates may vary greatly, in particular with regard

to strength, composition and porosity. Therefore, for each ap-

plication the suitability of Sika® AnchorFix-1 Adhesive must be

tested by first applying Sika® AnchorFix-1 Adhesive only to a

sample area. Check in particular bond strength, surface stain-

ing and discolouration.

CHARACTERISTICS / ADVANTAGES

Fast curing▪

Standard guns can be used▪

Can be used at low temperatures▪

High load capacity▪

Non-sag, even overhead▪

Styrene-free polyester resin▪

Low wastage▪

APPROVALS / STANDARDS

European Technical Approval (ETA) according to

ETAG001-5 for threaded bars only.

▪

Product Data Sheet

Sika® AnchorFix-1

June 2018, Version 01.02

020205010010000001

1 /

Summary of content (8 pages)

PAGE 1
PRODUCT DATA SHEET Sika® AnchorFix-1 HIGH STRENGTH, TWO COMPONENT ADHESIVE ANCHORING SYSTEM PRODUCT DESCRIPTION CHARACTERISTICS / ADVANTAGES Sika® AnchorFix-1 adhesive anchoring system has been specially formulated as a high-performance, two component adhesive anchor system for threaded and reinforcing bars in uncracked concrete.
PAGE 2
PRODUCT INFORMATION Packaging 10.1 fl.oz. (299 ml) Shelf Life 12 months from date of production All Sika® AnchorFix-1 cartridges have the expiry date printed on the label. Storage Conditions Cartridges should be stored in their original packaging, the correct way up, in cool conditions 41 °F to 77 °F (5 °C to 25 °C) out of direct sunlight. TECHNICAL INFORMATION Tensile Adhesion Strength 1. The above values represent mean ultimate values and allowable w orking loads.
PAGE 3
Design Considerations For details about adhesive anchoring design refer to the separate documentation provided: “Technical Documentation Sika® AnchorFix-1” Ref: 870 43 01 Allowable Tension, Nall = 0.33 x fu x nominal cross sectional area Allowable Shear, Vall = 0.17 x fu x nominal cross section area *The design professional on the job is ultimately responsible for the interpretation of the data provided above. Tension = 0.33 x fu x nominal cross sectional area Shear = 0.
PAGE 4
SYSTEM INFORMATION System Structure *The design professional on the job is ultimately responsible for the interpretation of the data provided above. APPLICATION INFORMATION Mixing Ratio Component A : component B = 10 : 1 by volume Coverage *Number of fixings assumes 30ml wastage in initial extrusion and holes filled to 3/4 full Product Data Sheet Sika® AnchorFix-1 June 2018, Version 01.
PAGE 5
Sag Flow Non-sag, even overhead Product Temperature Sika® AnchorFix-1 must be at a temperature of between 41 °F (5 °C) and 104 °F (40 °C) for application. Dew Point ▪ Beware of condensation. ▪ Beware of frost.
PAGE 6
APPLICATION INSTRUCTIONS MIXING SUBSTRATE QUALITY Getting the cartridge ready ▪ Mortar and concrete must be at the required strength. No need to be 28 days old. ▪ Substrate strength (concrete, masonry, natural stone) must be verified. ▪ Pull-out tests must be carried out if the substrate strength is unknown. ▪ The anchor hole must always be clean, dry, free from oil and grease etc. ▪ Loose particles must be removed from the holes.
PAGE 7
Pump approx. twice until both parts come out uniformly. Do not use this material. Release the gun pressure and clean the cartridge opening with a cloth. APPLICATION METHOD / TOOLS Anchors in solid masonry / concrete Drilling of hole with an electric drill to the diameter and depth required. Drill hole diameter must be in accordance with anchor size. Inject the adhesive into the hole, starting from the bottom, while slowly drawing back the static mixer.In any case avoid entrapping air.
PAGE 8
BASIS OF PRODUCT DATA LEGAL NOTES Results may differ based upon statistical variations depending upon mixing methods and equipment, temperature, application methods, test methods, actual site conditions and curing conditions. Prior to each use of any Sika product, the user must always read and follow the warnings and instructions on the product’s most current Product Data Sheet, product label and Safety Data Sheet which are available online at http://usa.sika.