Instructions / Assembly

ManualsBrandsSika ManualsBuilding materials10.1 fl. oz. Standard Anchoring Adhesive (6-Piece per Case)

Product Data Sheet

Sika AnchorFix® S

June 2018, Version 01.02

020205010010000003

PRODUCT DATA SHEET

Sika AnchorFix® S

Universal, two component adhesive anchoring adhesive

PRODUCT DESCRIPTION

Sika AnchorFix® S is a polyester based, 2-component,

contractor 6-pack (not sold individually), universal

anchoring adhesive.

USES

Sika AnchorFix® S may only be used by experienced

professionals.

As a fast curing anchoring adhesive for all grades of:

Rebars / reinforcing steel▪

Threaded rods▪

Bolts and special fastening systems▪

Concrete▪

Solid masonry▪

Hard natural stone

▪

Solid rock

▪

* These substrates may vary greatly, in particular with regard to strength,

composition and porosity. Therefore, for each application the suitability of Sika

Sika AnchorFix® S adhesive must be tested by first applying the Product only to a

sample area. Check in particular bond strength, surface staining and

discolouration.

CHARACTERISTICS / ADVANTAGES

Fast curing▪

Non-sag, even overhead▪

Low wastage▪

Multipurpose▪

PRODUCT INFORMATION

Packaging

10 fl.oz. (299 ml) cartridge

Shelf Life

12 months from date of production

All Sika AnchorFix® S cartridges have the expiry date printed on the label.

Storage Conditions

Cartridges should be stored in their original packaging, the correct way up, in

cool conditions between 41 °F to 77 °F (5 to 25 °C) out of direct sunlight.

1 /

Summary of content (8 pages)

PAGE 1
PRODUCT DATA SHEET Sika AnchorFix® S Universal, two component adhesive anchoring adhesive PRODUCT DESCRIPTION CHARACTERISTICS / ADVANTAGES Sika AnchorFix® S is a polyester based, 2-component, contractor 6-pack (not sold individually), universal anchoring adhesive. ▪ ▪ ▪ ▪ USES Fast curing Non-sag, even overhead Low wastage Multipurpose Sika AnchorFix® S may only be used by experienced professionals.
PAGE 2
TECHNICAL INFORMATION Tensile Adhesion Strength 1. The above values represent guideline Allowable Concrete Capacity / Bond Strength working loads based on the adhesive’s ability to bond to solid, normal weight concrete when anchor holes are drilled using the recommended drill bit diameter and properly cleaned. Allowable Concrete Capacity / Bond Strength working load values have been reduced using a safety factor of 4.0 in Tension and 3.0 in Shear, applied to the Average Ultimate values.
PAGE 3
SYSTEM INFORMATION System Structure *The design professional on the job is ultimately responsible for the interpretation of the data provided above. APPLICATION INFORMATION Mixing Ratio Component A : component B = 10 : 1 by volume Coverage *Number of fixings assumes 30ml wastage in initial extrusion and holes filled to 3/4 full Product Data Sheet Sika AnchorFix® S June 2018, Version 01.
PAGE 4
Sag Flow Non-sag, even overhead Product Temperature Sika AnchorFix® S must be at a temperature of between 41 °F (5 °C) and 68 °F (20 °C) for application. Dew Point ▪ Beware of condensation. ▪ Beware of frost. Cure Time Temperature 96–104 °F (35–40 °C) 87–95 °F (30–35 °C) 78–86 °F (25–30 °C) 69–77°F (20–25 °C) 51–68 °F (10–20 °C) 41–50 °F (5–10 °C) Open time - T gel 1.
PAGE 5
APPLICATION INSTRUCTIONS MIXING SUBSTRATE QUALITY Getting the cartridge ready ▪ Mortar and concrete must be at the required strength. No need to be 28 days old. ▪ Substrate strength (concrete, masonry, natural stone) must be verified. ▪ Pull-out tests must be carried out if the substrate strength is unknown. ▪ The anchor hole must always be clean, dry, free from oil and grease etc. ▪ Loose particles must be removed from the holes.
PAGE 6
APPLICATION METHOD / TOOLS Anchors in solid masonry/concrete Drilling of hole with an electric drill to the diameter and depth required. Drill hole diameter must be in accordance with anchor size. The drill hole must be cleaned with a blow pump or by compressed air, starting from the bottom of the hole. (at least 2×) Important: use oil-free compressors. The drill hole must be thoroughly cleaned with the special steel brush (brush at least 2×).
PAGE 7
Inject the adhesive into the hole, starting from the bottom, while slowly drawing back the static mixer.In any case avoid entrapping air. For deep holes extension tubing can be used. Insert the anchor with a rotary motion into the filled drill hole. Some adhesive must come out of the hole. Important: the anchor must be placed within the open time. During the resin hardening time the anchor must not be moved or loaded. Wash tools immediately with Sika® Colma Cleaner.
PAGE 8
LEGAL DISCLAIMER • KEEP CONTAINER TIGHTLY CLOSED • KEEP OUT OF REACH OF CHILDREN • NOT FOR INTERNAL CONSUMPTION • FOR INDUSTRIAL USE ONLY • FOR PROFESSIONAL USE ONLY Prior to each use of any product of Sika Corporation, its subsidiaries or affiliates (“SIKA”), the user must always read and follow the warnings and instructions on the product’s most current product label, Product Data Sheet and Safety Data Sheet which are available at usa.sika.