INTELLIKNIGHT MODEL 5700 Addressable Fire Control Panel Installation and Operations Manual Part Number 151295 Rev E 11/2006
Installation Procedure Adherence to the following will aid in problem-free installation with long-term reliability: Installation Precautions - Adherence to the following will aid in problem-free installation with long-term reliability: WARNING - Several different sources of power can be connected to the fire alarm control panel. Disconnect all sources of power before servicing.
While installing a fire alarm system may make lower insurance rates possible, it is not a substitute for fire insurance! An automatic fire alarm system - typically made up of smoke detectors, heat detectors, manual pull stations, audible warning devices, and a fire alarm control with remote notification capability - can provide early warning of a developing fire. Such a system, however, does not assure protection against property damage or loss of life resulting from a fire.
Contents Section 1 Introduction .............................................................................................................................................. 1-1 1.1 Overview of Basic System ....................................................................................................................... 1-1 1.1.1 Hardware Features ............................................................................................................................ 1-1 1.1.2 Software Features ..
Model 5700 Installation and Operation Manual Section 4 Control Panel Installation 4.1 ii ...................................................................................................... 4-1 Mounting the Control Panel Cabinet ....................................................................................................... 4-1 4.1.1 Preventing Water Damage ................................................................................................................ 4-1 4.1.
Contents 4.14.6 Transmitter Activated by Dry Contacts .......................................................................................... 4-38 Section 5 SLC Device Installation ............................................................................................................ 5-1 5.1 5.2 5.3 List of SLC Devices ................................................................................................................................. 5-1 Maximum Number of Devices ...................
Model 5700 Installation and Operation Manual 7.4 7.5 7.6 7.7 7.8 7.9 iv 7.3.1.4 Cadence Patterns .................................................................................................................. 7-10 7.3.2 Add Zone ........................................................................................................................................ 7-11 7.3.3 Delete Zone ..................................................................................................................
Contents Section 8 System Operation 8.1 8.2 8.3 8.4 8.5 8.6 Annunciator Description .......................................................................................................................... 8-1 8.1.1 LCD Displays ................................................................................................................................... 8-1 8.1.2 Banner ...............................................................................................................................
Model 5700 Installation and Operation Manual Section 11 Installation Records .................................................................................................................... 11-1 11.1 Detector and Module Point Record ........................................................................................................ 11-1 Appendix A Compatible Devices .....................................................................................................................
Section 1 Introduction The 5700 Fire Alarm Control / Communicator is an addressable fire control system that meets the requirements of UL 864. 1.1 Overview of Basic System The 5700 base system is 50 addressable point system with a built-in annunciator which can also be used to program the system. 1.1.1 • • • • • • • • • • • • • • • Hardware Features The 5700 panel has one signaling line circuit (SLC) that supports 50 addressable devices. 2.
Model 5700 Installation and Operation Manual 1.1.2 Software Features • Advanced smoke detector features: –Automatic drift compensation –Maintenance alert region –Point status eliminates calibrated smoke test requirements for NFPA 72 • “JumpStart” feature for easy programming • Non-volatile event history stores 1000 events • A choice of output patterns available for notification outputs, including ANSI 3.
Introduction 1.3 Compatible Products The chart below lists the products available from Silent Knight for use with the 5700. Type of Device Model Description Addressable See Section 5.1 for a list of compatible devices. SLC Devices 5824 Serial/Parallel Printer Allows a printer to be attached for the system for on-site event logging, detector Interface Module status and event history reports. Two maximum per system. 5895XL Provides additional power, six Flexput circuits, and two Form C relays.
Model 5700 Installation and Operation Manual Limitations of Fire Alarm Systems Manufacturer recommends that smoke and/or heat detectors be located throughout a protected premise following the recommendations of the current edition of the National Fire Protection Association Standard 72 (NFPA 72), manufacturer’s recommendations, State and local codes, and the recommendations contained in Guide for the Proper Use of System Smoke Detectors, which is made available at no charge to all installing dealers.
Introduction • Warning devices (including horns, sirens, and bells) may not alert people or wake up sleepers who are located on the other side of closed or partially open doors. A warning device that activates on a different floor or level of a dwelling or structure is less likely to awaken or alert people. Even persons who are awake may not notice the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing traffic.
Model 5700 Installation and Operation Manual Requirements and recommendations for proper use of fire alarm systems including smoke detectors and other fire alarm devices: Early fire detection is best achieved by the installation and maintenance of fire detection equipment in all rooms and areas of the house or building in accordance with the requirements and recommendations of the current edition of the National Fire Protection Association Standard 72, National Fire Alarm Code (NFPA 72), the manufacturer’s
Section 2 Agency Listings, Approvals, and Requirements Install and maintain in accordance with NFPA 72. Detector spacing shall be in accordance to NFPA 72. End-of -line relays and resistors shall be placed within the electrical box located and the end of the initiating circuit. Testing and maintenance should be performed according to NFPA 72. 2.
Model 5700 Installation and Operation Manual 7. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice to allow you to make the necessary modifications to maintain uninterrupted service. Warning This device has been verified to comply with FCC Rules Part 15.
Agency Listings, Approvals, and Requirements j) If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this 5700 does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or qualified installer.
Model 5700 Installation and Operation Manual 2.2.2 Requirements for Central Station Fire Alarm Systems 1. Use both phone lines. Enable phone line monitors for both lines. 2. You must program a phone number and a test time so that the 5700 sends an automatic daily test to the central station. 3. Do not use the ground start option. 4. The AC Loss Hours option must be set from 6-12 hours. 5. The Attempts to Report option must be set for 5. 2.2.
Section 3 Before You Begin Installing This section of the manual is intended to help you plan your tasks to facilitate a smooth installation. Please read this section thoroughly, especially if you are installing a 5700 panel for the first time. 3.1 What’s in the Box? The 5700 ships with the following hardware: • A cabinet with all hardware assembled • Two keys for the front door • Installation and Operation manual P/N 151295. • Ten 4.
Model 5700 Installation and Operation Manual 3.3 Electrical Specifications Table 3-1 list the terminal block on the 5700 as well as a description of the each individual terminal and their respective electrical rating. For location of the terminals refer to Figure 3-2. See also Section 4 for installation. Table 3-1: Terminal Descriptions Label Rating Terminal No.
Before You Begin Installing 3.4 Wiring Specifications Induced noise (transfer of electrical energy from one wire to another) can interfere with telephone communication or cause false alarms. To avoid induced noise, follow these guidelines: • Isolate input wiring from high current output and power wiring. Do not pull one multiconductor cable for the entire panel.
Model 5700 Installation and Operation Manual 3.5 Board Assembly Diagram On-board Annunciator 120 VAC, 60 Hz, 1.5A AC Power Input Form C Relays Programming Port Terminal Block 2 Battery Connector 24 VDC Terminal Block 1 Phone Lines SLC In/Out, SLC Programming Form C Trouble Relay NAC/Aux Power Circuits SBUS Connections Figure 3-2 Model 5700 Assembly Figure 3-2 shows the circuit boards, and annunciator.
Before You Begin Installing 3.6 Calculating Current Draw and Standby Battery This section is for helping you determine the current draw and standby battery needs. 3.6.1 Worksheet Requirements The following steps must be taken when determining 5700 current draw and standby battery requirements. 1. For the 5700, the worst case current draw is listed for the panel, addressable devices, and all SBUS expanders.
Model 5700 Installation and Operation Manual 3.6.1.1 Current Draw Worksheet for SLC Devices Use Table 3-2 to determine current requirements during alarm/battery standby operation. (Copy the page if additional space is required.) Table 3-2: Current Calculation Worksheet Device For each device use this formula: # of Devices This column Fire Panel (Current draw from battery) Addressable SLC Devices SD500-AIM SD500-MIM SD500-ARM SD500-PS/SD500-PSDA SD500-AIS SD505-AHS SD505-APS 1 (50 max.
Before You Begin Installing Table 3-2: Current Calculation Worksheet Device # of Devices Current per Device Standby Current Alarm Current Accessories Modules 5860 Remote Fire Alarm Annunciator 5824 Serial / Parallel Module 5496 Notification Power Expander 5865-4 LED Annunciator (8 max.) (2 max.) (8 max.) (with reset and silence switches) 5865-3 LED Annunciator (8 max.) 5880 Generic LED Driver Module 5883 Relay Interface A Auxiliary Devices3 B C D E F G H I J (32 max.
Model 5700 Installation and Operation Manual 3.6.1.2 Maximum Battery Standby Load The table below shows the maximum battery standby load for the 5700 based on 24 and 60 hours of standby. The standby load calculations of line D in the Current Draw Calculation Worksheet (Table 3-2) must be less than the number shown in the table below for the battery size used and standby hours required. Rechargeable Battery Size * Max. Load for 24 hrs. Standby, 5 mins. Alarm *Max. Load for 60 hrs. Standby, 5 mins.
Section 4 Control Panel Installation Caution! To avoid the risk of electrical shock and damage to the unit, power should be OFF at the control panel while installing or servicing. 4.1 Mounting the Control Panel Cabinet Read the environmental specifications in Section 3.2 before mounting the 5700 panel. The 5700 cabinet dimensions are: 12-3/4" W x 15-1/8" H x 3-3/8" D (32.39 cm W x 38.42 cm H x 8.57 cm D).
Model 5700 Installation and Operation Manual 4.1.3.1 Installing the Dead Front Follow these steps to properly install the dead front panel into the control panel cabinet. 1. Remove the top two annunciator screws, do not discard them they will be reused. See Figure 4-1 for annunciator screw location. 2. Set the dead front into the cabinet as shown in Figure 4-1. 3. Reinsert the two annunciator screws as shown in Figure 4-1. Dead Front Panel Figure 4-1 Dead Front Installation and Removal 4.
Control Panel Installation 4.2 AC Connection At installation, connect the AC terminals to the power source as shown in Figure 4-2. It may be necessary for a professional electrician to make this connection. The AC terminals are rated at 120 VAC, 60 Hz, 1.5A .
Model 5700 Installation and Operation Manual 4.3 Battery Connection The control panel battery charge capacity is 7.0 to 35 AH. The main control cabinet can house batteries up to 7 AH, larger capacity batteries can be housed in a Remote Battery Box (P/N RBB). See Section 4.3.1 for deteails.Use 12V batteries of the same AH rating. Determine the correct AH rating as per your current load calculation (see Section 3.6). Maximum battery charging current 3.1 Amps.
Control Panel Installation 4.3.1 RBB Accessory Cabinet The Model RBB Accessory cabinet can be used when your backup batteries requirements use backup batteries that are too large to fit into the main control panel cabinet. The RBB cabinet holds batteries up to the 35 AH size. The RBB dimensions are 16" W x 10" H x 6" D (40.64 cm W x 25.4 cm H x 15.24 cm D). 4.3.1.1 Installing the RBB Accessory Cabinet and Batteries To properly install the accessory cabinet and backup batteries, follow these steps: 1.
Model 5700 Installation and Operation Manual 3. Run extended battery cable from control panel cabinet through conduit to RBB cabinet. See Figure 4-6. RBB Cabinet Cover Screws Conduit Coupler Conduit + - + - RBB Cabinet Cover Screws Figure 4-6 Battery Connections in the RBB Cabinet Note: Figure 4-6 is an example of how the wire connections can be routed.
Control Panel Installation 4.4 SBUS Wiring This section contains information on calculating SBUS wire distances and the types of wiring configurations (Class B). 4.4.1 Calculating Wiring distance for SBUS modules The following instructions will guide you in determining the type of wire and the maximum wiring distance that can be used with control panel SBUS accessory modules.
Model 5700 Installation and Operation Manual These cases are marked in the chart with an asterisk (*). Maximum length can never be more than 6,000 feet, regardless of gauge used. (The formula used to generate this chart is shown in the note below). Table 4-1: Wire Distances Per Wire Gauge Using Copper Wire Wiring Distance: SBUS Modules to Panel Total Worst Case Current Draw (amps) 22 Gauge 18 Gauge 16 Gauge 14 Gauge 0.100 1852 ft. 4688 ft. * 6000 ft. * 6000 ft. 0.200 926 ft. 2344 ft. 3731 ft.
Control Panel Installation Wiring Distance calculation example: Suppose a system is configured with the following SBUS modules: 2 - Module 5860 Fire Annunciator 1 - 5496 Notification Power Expander 1 - 5865 LED Fire Annunciator 1 - 5824 Parallel/Serial Interface The total worst case current is calculated as follows: 5860 Current Draw = 2 x .100 amps = .200 amps 5496 Current Draw = 1 x .010 amps = .010 amps 5865 Current Draw = 1 x .200 amps = .145 amps 5824 Current Draw = 1 x .040 amps = .
Model 5700 Installation and Operation Manual 4.4.2 Wiring Configurations Figure 4-8 illustrates Class B configuration. Supervised Power Limited Figure 4-8 SBUS Class B Wiring 4.4.2.1 How to Power SBUS Devices From Auxiliary Power Supply Figure 4-9 illustrates how to power SBUS devices from an Auxiliary Power Supply such as the 5495 or 5499, when the maximum number of SBUS devices exceeds the SBUS power requirments.
Control Panel Installation 4.5 Remote Annunciator 5860 Installation The optional Model 5860 Remote Annunciator, shown in Figure 4-10, performs the same functions as the on-board annunciator. Operation is identical. Up to 8 annunciators can be added to the 5700 system. Figure 4-10 Model 5860 Remote Annunciator, Front View 5860 installation involves the following steps: 1. Make sure power is off at the panel. 2. Mount the 5860 in the desired location (see Section 4.5.1). 3.
Model 5700 Installation and Operation Manual 4.5.1 Mounting the 5860 This section of the manual describes mounting the remote annunciator. The annunciator can be flush- or surface-mounted. Figure 4-11 shows the parts of the annunciator. Instructions for disassembling and mounting appear on the following pages.
Control Panel Installation The 5860 comes from the factory fully assembled. You must disassemble it for mounting. To disassemble the annunciator, use a 5/64 hex wrench to remove the set screws, located on the bottom of the annunciator bezel. (See Figure 4-12 for location of the set screws.) Figure 4-12 Annunciator Back Box and Bezel Details 4.5.1.1 Flush Mounting This section of the manual describes flush mounting. You can flush-mount with or without an electrical box.
Model 5700 Installation and Operation Manual Flush Mounting with an Electrical Box The 5860 annunciator can be used with the following types of electrical boxes: 4S, singlegang, and double-gang. If an electrical box is used, the box must be 1-3/8” back from the face of the wall to accommodate the annunciator. Studs used with an electrical box must be two by fours (or larger). Figure 4-13 Placement of Electrical Box for Flush Mounting Flush Mounting Steps 1.
Control Panel Installation 4. After the annunciator wiring to the panel has been completed (described in Section 4.5.2), replace the electronic assembly in the back box. Place the bezel over the back box and tighten the set screws on the bezel. Figure 4-14 Flush Mounting the Back Box 4.5.1.2 Surface Mounting The 5860 can be mounted directly to a surface or can be attached to a single, double, or foursquare electrical box. The Model 5860TG/TR trim ring kit is available for use when surface mounting. 1.
Model 5700 Installation and Operation Manual 4.5.2 Model 5860 Connection to the Panel Connect the 5860 to the panel as shown in Figure 4-15. Supervised Power Limited Figure 4-15 Model 5860 Connection to the Panel 4.6 5824 Serial/Parallel Printer Interface Module Installation The 5824 serial/parallel printer interface module allows you to connect a printer to the panel, so you can print a real-time log of system events, a report of detector status, and event history.
Control Panel Installation 5. Connect a printer to the 5824 as shown in Figure 4-17.
Model 5700 Installation and Operation Manual 4.6.1 Selecting 5824 Options Configuring the 5824 includes the following steps: • Add the module to the system. JumpStart will add the module automatically (see Section 6.1). You can also add it manually (see Section 7.2.2). • Select a name, if desired (see Section 7.2.1.1). • Select options for the printer and the output port. See below. Printer and Output Port Options 1. From the Main Menu, select 2. Select 1 for Module. 3.
Control Panel Installation 4.7 5880 LED Driver Module The 5880 is an LED driver board that can be used in a wide variety of applications, including as an interface with most customized floor plan annunciator boards. The 5880 can drive up to 40 LEDs and has one PZT controller. The 5880 also has eight inputs for dry contact monitoring. The following sub-sections describe hardware installation. Refer to Section 6 for programming information. 4.7.
Model 5700 Installation and Operation Manual 4.7.2 FACP Connection The 5880 connects to the panel via the SBUS. Make connections as shown in Figure 4-20. After the 5880 is connected to the panel, it must be added to the system. This programming step is described in Section 4.9.
Control Panel Installation 4.7.3 LED Wiring There are four 12-pin connectors on the 5880 board for connecting LEDs. Each LED gets its power from Pin 11. Internal resistors are sized so that there is approximately 10 mA of current for each LED, no series resistors are required. LED outputs can be mapped to output circuits. See Section 6 for programming details. Wire the LEDs as shown in Figure 4-21. On connector P1, Pin 12 is a programmable open collector output for controlling a PZT.
Model 5700 Installation and Operation Manual 4.7.4 Dry Contact Wiring The 8 input circuits on the 5880 board are for monitoring switch inputs-any type of switch supported by the control panel can be used with the 5880. For example, you can use a 5880 to monitor pull stations, water flow, tamper, reset, or silence switches. Wire dry contacts as shown in Figure 4-22. Notice grouping of terminals; power terminals are shared by two inputs. Supervised Model 7628 4.
Control Panel Installation 4.8 5865-3 / 5865-4 LED Annunciator Installation The 5865-3 and 5865-4 are LED annunciators. The 5865-4 has 30 mappable LEDs, remote silence and reset key switches, and a general system trouble LED. The 5865-3 has 30 mappable LEDs only. These are arranged as 15 pairs of red (typically used for alarm) and yellow (typically used for trouble) LEDs. Installation of the 5865-3 and 5865-4 is identical.
Model 5700 Installation and Operation Manual 4.8.2 5865 Mounting Mount the 5865-4 to a standard 4-gang electrical box. Mount the 5865-3 to a standard 3-gang electrical box. In Figure 4-25, the 5865-4 attached to a 4-gang box is used as an example. Figure 4-25 5865 Mounting Example The 5865 ships with a set of zone description labels that can be inserted into the 5865 board assembly. These labels can be used in a typewriter or can be written on by hand.
Control Panel Installation 4.9 Configuring Modules This section describes how to configure any system hardware modules that have been added to the system. 4.9.1 Assigning Module IDs When installing a hardware module (such as, 5824, 5860, 5496, 5865-3 or 5865-4), you must use the dipswitches on the module to assign an ID# to the module. Figure 4-27 shows all possible dipswitch positions and their correlation to a numerical ID. For example, to select ID 2, place dipswitch 2 in the up position.
Model 5700 Installation and Operation Manual 4.10 Telephone Connection Connect the telephone lines as shown in Figure 4-28. The Model 7860 phone cord is available from Silent Knight for this purpose. A number of programmable options are available for customizing telephone lines. These options are described in Section 7.6. 5211 Ground Start Relay Socket Supervised Figure 4-28 Connection of Telephone Lines 4.11 5211 Ground Start Relay Note: Do not use ground start in UL installations.
Control Panel Installation 4.12 Notification Appliance/Auxiliary Power Circuits Two outputs are built-in to the 5700 FACP which can be programmed to be used as NACs (Class A or Class B) or as Aux power. This section of the manual explains how to install conventional notification appliances and how these terminals can be used for auxiliary power. 4.12.
Model 5700 Installation and Operation Manual 4.12.1.2 Class A Notification Wiring You must use an appliance from the list of compatible appliances in the Appendix at the back of this manual. To install a Class A notification appliance circuit: 1. Wire the Class A notification appliances as shown in Figure 4-30. Caution For proper system supervision do not use looped wire under terminals marked – and + of the Flexput connectors. Break wire runs to provide supervision of connections. 2.
Control Panel Installation 4.12.2 Auxiliary Power Installation NAC Circuits 1and 2 on the control panel can be used as auxiliary power circuits. The three types of auxiliary power available are: • Door Holder (see section 4.12.2.1) • Constant (see section 4.12.2.2) • Resettable Power (see section 4.12.2.3) Auxiliary power circuits are power limited. Each circuit can source up to 2.5A (total current for system must not exceed 2.5A). To install an auxiliary power circuit: 1.
Model 5700 Installation and Operation Manual 4.12.2.2 Constant Power Use constant power for applications that require a constant auxiliary power source. Power is always present at Constant circuits. 4.12.2.3 Resettable Power Resettable power is typically used to power beam detectors, flame detectors and conventional 4-wire smoke detectors. For circuits selected as Resettable, 27.4 volt power is always present at the terminals unless a system reset occurs.
Control Panel Installation 4.14 Remote Station Applications 4.14.1 Keltron Model 3158 Installation The control panel is compatible with Keltron Model 3158, used for direct connection to a Keltron receiver. The 3158 reports alarms, supervisories, and troubles. The 3158 is intended for connection to a polarity reversal circuit of a remote station receiving unit having compatible ratings. The steps for connecting the 3158 to the control panel.
Model 5700 Installation and Operation Manual 4.14.2 City Box Connection Using the 5220 Module This section describes how to connect the control panel to a municipal fire alarm box or “city box” as required by NFPA 72 Auxiliary Protected Fire Alarm systems for fire alarm service. The city (master) box is an enclosure that contains a manually operated transmitter used to send an alarm to the municipal communication center which houses the central operating part of the fire alarm system.
Control Panel Installation 4.14.3 NFPA 72 Polarity Reversal 4.14.3.1 Using the 5220 Module When the 5220 is wired and programmed for polarity reversal, it reports alarm and trouble events to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset. If an alarm condition occurs, the alarm relay will close, overriding the trouble condition. Standby Current: 100 mA Alarm: 100 mA Max.
Model 5700 Installation and Operation Manual 5. If necessary, adjust loop current using the potentiometer (R10) on the 5220 board . Normal loop current is 2-to-8 mA with a 1k ohm remote station receiving unit. Maximum loop resistance is 3k ohm. Program Relay for Alarm. Note: NAC circuit 1 and Relay 2 used as examples. Either NAC circuit and Relay circuit can be used. Max Voltage: 27.
Control Panel Installation 4.14.3.2 Using the 7644 Module When the 7644 is used for polarity reversal, it allows alarm and trouble events to be reported to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset. To install the 7644 for polarity reversal: 1. Wire the 7644 to the control panel as shown in Figure 4-36. Do not install an EOL resistor on the terminals of the NAC circuit used.
Model 5700 Installation and Operation Manual 4.14.4 Using the SD500-ARM Addressable Relay Module When the SD500-ARM is wired for polarity reversal, it reports alarm and trouble events to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset. Relay 2 must be programmed for Alarm (default). Max Current: 1A Max. Voltage: 27.
Control Panel Installation 4.14.5 Using a MR-201/T Control Relay From Air Products When the MR-201/T control relay is wired for polarity reversal, it reports alarm and trouble events to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset. If an alarm condition occurs, the alarm relay will close, overriding the trouble condition. Current: Operating Voltage: Resistance: 15 mA max.
Model 5700 Installation and Operation Manual 4.14.6 Transmitter Activated by Dry Contacts This section describes the connection of a UL 864 listed remote station transmitter to the 5700 FACP dry contacts. The FACP contacts must be supervised by the remote station transmitter module using end-of-line resistors (ELRs) with a value determined by the transmitter manufacturer. Power is also provided by the remote station transmitter manufacturer.
Section 5 SLC Device Installation Caution! To avoid the risk of electrical shock and damage to the unit, power should be OFF at the control panel while installing or servicing. 5.1 List of SLC Devices The following SLC devices can be used with the control panel. See the appropriate section number in this manual or the device installation instructions (packaged with the device) for more information. Model Number Model Name/Description Section No.
Model 5700 Installation and Operation Manual 5.2 Maximum Number of Devices The 5700 supports 50 addressable devices. 5.3 Wiring Requirements for SLC Devices The following information applies to all SLC devices. Refer to the section that describes the type of device you are installing for details. 5.3.1 Wiring 5815XL in Style 4 (Class B) Configuration No special wire is required for addressable loops.
SLC Device Installation Figure 5-1 and Figure 5-2 show how wire length is determined for out-and-back tap and T-tap style wiring. Figure 5-1 Calculating wire run length for a simple out and back tap When using T-taps, the total length of all taps and the main bus must not exceed 40,000 feet. This requirement must be met in addition to the maximum distance requirements for the various wire gauges.
Model 5700 Installation and Operation Manual 5.3.2 Wiring 5815XL in Style 6 & 7 (Class A) Configuration Figure 5-3 illustrates how to wire the SLC loop for Style 6 or Style 7 Class A installations. Note: Style 6 does not use short circuit isolator devices. Figure 5-3 Class A SLC Configuration Note: No t-taps allowed on class A SLC loops. Caution For proper system supervision do not use looped wire under terminals marked SLC + and – of the SLC device connectors.
SLC Device Installation 5.4 Wiring Detectors The information in this section applies to the following models: SD505-AHS Heat Detector, SD505-AIS Ionization Smoke Detector, and SD505-APS Photoelectric Smoke Detector. To wire SD505-APS, SD505-AHS, or SD505-AIS detectors: 1. Wire device bases as shown in Figure 5-4. 2. Set the address for each device as described in Section 5.5.
Model 5700 Installation and Operation Manual 5.5 Addressing Devices This section tells how to address detectors and modules. 5.5.1 SD505-APS, SD505-AHS, & SD505-AIS The SD505-APS photoelectric smoke detector, SD505-AHS heat detector, and SD505-AIS ionization smoke detector are easily addressed at the FACP. The Installer Code is required to perform this task. To address a SD505-APS, SD505-AHS, or SD505-AIS: 1. Connect a detector base temporarily to the programming terminals as shown in Figure 5-5.
SLC Device Installation 5.5.2 SLC Devices with Dip Switches Input and relay module addresses are set using the dip switches on the module board. The chart below shows the available addresses. For example, to select address 3, place dip switches 1 and 2 in the up position. The range of valid addresses is 1-50. 0 is an invalid address.
Model 5700 Installation and Operation Manual 5-8 151295
Section 6 Programming Overview This section of the manual is intended to give you an overview of the programming process. Please read this section of the manual carefully, especially if you are programming the control panel for the first time. The JumpStart feature automates many programming tasks and selects default options for the system. You will run JumpStart at least once when you are installing the system. See Section 6.1 for details.
Model 5700 Installation and Operation Manual 6.1.1 Input Points JumpStart will determine the number and type of input points (detectors or contact monitor modules) on each SLC loop. JumpStart assigns the correct detector type (heat, or photoelectric), so the installer does not need to edit device type for detectors. Any contact monitor modules on the system will be assigned type "Manual Pull." The installer will need to manually change the switch type if manual pull is not correct.
Programming Overview 5. When the message "Configuring System Done" displays, press any key to continue. 6. Select one of the following options from the menu that displays. 1 - Review System Press 1 if you need to review the JumpStart configuration. 2 - Repeat JumpStart Press 2 if you need to rerun JumpStart for any reason. 3 - Accept Configuration 1. If you are ready to make the JumpStart configuration permanent, select 3 . 2.
Model 5700 Installation and Operation Manual 6.2 Mapping Overview This section of the manual is an overview of mapping. Details about how to select mapping options appear in the appropriate subsections in Section 7. Mapping is an important concept with the control panel. In general terms, mapping is assigning or linking events to outputs that should activate when events occur.
Programming Overview 6.2.1 Input Point Mapping Input points are assigned to input zones. Any input point can be assigned to any input zone. (Input points can be assigned to one zone only. An input point can be designated as "Unused," which means it has not been assigned to a zone.
Model 5700 Installation and Operation Manual 6.2.2 Output Circuit Mapping Figure 6-3 is a simple example showing how to assign notification and relay output circuits to groups. For an example of a simple floor above/floor below application, see Figure 6-5.
Programming Overview 6.2.3 Zone Event Mapping There are 8 types of events that can occur in zones (see below). For each event type, you can activate up to 8 output groups and patterns. If it is necessary to map to more than 8 output groups, an output group template may be used (see Section 7.4.5 for information on output group templates).
Model 5700 Installation and Operation Manual Figure 6-5 Example of Zone Events Mapped to Output Groups and Patterns 6-8 151295
Programming Overview 6.2.4 Mapping LED Points Figure 6-6 is a simple example showing how LED points are mapped to zones and output groups. Typically you would create two output groups for each zone, one for alarms and one for troubles. (LED points are available when Models 5865-3/4 and/or 5880 are used with the system.
Model 5700 Installation and Operation Manual 6.3 Programming Using the 5660 Silent Knight Software Suite You can use the 5660 Silent Knight Software Suite (SKSS) to program the control panel onsite or remotely. SKSS is an optional software package that lets you easily program the control panel using a Windows-based computer and a modem* (not sold by Silent Knight). When using SKSS, you can set up the programming options for the panel, save the options in a file, then download the file to the panel.
Programming Overview 6.4.1 Entering / Exiting the Program Menu To enter the Program Mode: 1. Press to display the main menu. or 2. Enter the installer code if requested. 3. Select 7 for Program Menu. Display reads: Initializing Please wait . . . The menus described in Section 7 of this manual will display. Section 7.6 of this manual is a quick reference listing all programmable options and JumpStart defaults.
Model 5700 Installation and Operation Manual 6.4.3 Selecting Options and Entering Data There are several ways to make programming selections using the control panel depending on which screen you are currently using. The chart below is a generic explanation. To Press Select from a menu. Enter the number of the option. Enter numeric data. Press the appropriate number on the annunciator. Enter text (alphanumeric data).
Programming Overview 6.5 Programming Menu Quick Reference This section of the manual lists all Program Menu options in the order they appear on the submenus. Default settings are indicated in text or marked with an asterisk. The comments column provide quick information and a reference to a section (if applicable) which has more detailed information.
Model 5700 Installation and Operation Manual Menu Options/Defaults Group Name Comments Enter Name1 Enter Number1 Enter Name2 Enter Number2 Section 7.4.1.1 *SILENCE NON-SIL Silencing Options Edit Group Auto Unsilence SIL-INHIB SHUTDOWN Select Group Group Properties Group1 Group Active With: Group Activates for all Man.
Programming Overview Menu Options/Defaults Comments MAN_PULL WATERFLOW SUPERVSY LATCH NLATCH LATCH NLATCH FIREDRILL SILENCE RESET PAS_ACK ZN_AUX1 SWITCH SLC Loop (cont.) ZN_AUX2 Enter Pt SYS_AUX1 SYS_AUX2 LATCH NLATCH LATCH NLATCH LATCH NLATCH LATCH NLATCH Section 7.5 DETECT SW TAMPER Point (cont.
Model 5700 Installation and Operation Manual Menu Options/Defaults Edit Account # Comments For each account (1-4), select: *123456 Edit Format *Contact ID Y (Yes) N (No) M (Must) Y (Yes) Rep.
Programming Overview Menu Options/Defaults System Trouble Alarm Silence Trbl Silence Trouble Events System Event Outputs User Selected Fire Drill Sys Alarm Cadence System Aux1 System Aux2 0 - 90 Seconds Water Flow Delay System Options (cont.) Select Group Select Cadence Select Group Select Cadence Select Group Select Cadence Group Tr SBUS Com SBUS Pwr SLC Loop AC Loss Battery Gnd Flt Phone Ln Account Printer Aux Pwr Sys Sw DST Misc. Options 2 Misc.
Model 5700 Installation and Operation Manual Menu JumpStart AutoPrg Computer Account Options/Defaults No Yes Computer Account *123456 # Computer Access *0 Code Comments Section 7.7 Section 7.8 See Section 7.8 for programming phone number. Computer Phone # Up to 24 digits Edit Name Edit Access Code Access Codes Select Profile (01 - 20) Edit Panel Functions System Reset System Silence System Event Ack.
Section 7 Programming This section of the manual describes how to manually program the control panel from the built-in annunciator. Each subsection discusses these menu options in detail. All options described in this section can be performed using the Silent Knight Software Suite 5660. Important! Before any customized programming is done, JumpStart should be run first. After JumpStart is run, thoroughly test the system.
Model 5700 Installation and Operation Manual 7.2 Modules This section lists the options available under the module option in the program menu. The types of modules available for the control panel are, 5860 (Keystation), 5824 (Serial/Parallel input/output), 5880 (LED Input/Output module), 5496 (Intelligent Power Module), and a 5865 (LED Annunciator). 7.2.1 Edit Modules The features that can be edited when this option is selected are, module name, and class of wiring (Class A or Class B).
Programming 7.2.1.2 Module, Wiring Class 8. Choose the class of wiring you wish to use for this module by pressing the then press 7.2.2 or arrow, . Adding a Module You must be in the Main Menu to perform this task. If necessary, enter the Installer Code. If you need to add a new hardware module to the system, follow the steps below. 1. Press to display the main menu. or 2. Enter the installer code if requested. 3. Select for Program Menu. 7 Display reads: Initializing Please wait . . . 4.
Model 5700 Installation and Operation Manual 7.3 Zone Through the zone option in the program menu you can edit, add, delete, and view zone points. Selections made here affect all detectors and switches in the zone. Up to 125 zones can be used in the system. 7.3.1 Edit Zone Features that can be edited through the edit zone option are, edit zone name, zone properties (which includes, zone type, and detector sensitivity), and zone output mapping. To edit a zone, follow these steps: 1.
Programming 8. Select the characters for the zone name by pressing the character is shown then press . or arrow until the desired OR Enter the Numerical Designator for the character you want, then press . See Appendix B Table B-1 of this manual for a list of available characters and their numeric designators. 9. Repeat step 8 until the name is complete. 10. Press when the name is complete. 7.3.1.
Model 5700 Installation and Operation Manual Alarm Delay Characteristics 3. Select the alarm delay characteristics by pressing the or arrow. Table 7-1 list the delay choices and a description of each. Table 7-1: Alarm Delay Types Type of Delay Description 1-Count One Count (No Delay). When this option is enabled, an alarm occurs immediately when a single device of any of the following types goes into alarm: detector, manual pull, water flow, Aux1 or Aux2.
Programming Heat Temperature Setting Use this feature to set the temperature at which heat detectors will respond. The range is 135° to 150° F. All detectors in the zone will respond in the same way. The Model SD505-AHS Heat Detector is an absolute temperature device. This means that it responds to an alarm immediately if the temperature in the zone goes above the programmed temperature. 5. Enter the temperature at which the heat detector will respond.
Model 5700 Installation and Operation Manual To map zone events to outputs, follow these steps: 1. From the Main Menu, select for Program Menu. 7 2. From the Program Menu, select 3. From the next menu, select 1 2 for Zone. for Edit Zone. 4. Enter the zone number you wish to edit. 5. From the next menu, select 3 for Zone Outputs. 6. From the next screen, a list of 8 event types will display. Select the event type you want to program. A screen similar to the one shown in Figure 7-3 will display.
Programming Example or Zone Mapping: Suppose you want to program Zone 1 so that: • Any alarm (detector, water flow or manual pull) would activate Output Group 1 using the ANSI cadence pattern. • Manual pull alarm would activate Output Group 3 using constant output. • Troubles would activate Output Group 2 using the zone-coded cadence pattern. To accomplish this you need to access the screen for each event and then select your output groups. Figure 7-4 shows how you would program this application.
Model 5700 Installation and Operation Manual 7.3.1.4 Cadence Patterns The cadence patterns shown in Figure 7-5 are available for use with the control panel. Cadence patterns can be selected by event type for each zone or for the entire system. Special cadence patterns can be selected for fire drills and any auxiliary system switches used with the system.
Programming 7.3.2 Add Zone To add a zone, follow these steps: 1. Press to display the main menu. or 2. Enter the installer code if requested. 3. Select for Program Menu. 7 Display reads: Initializing Please wait . . . 4. Press 2 to enter zone menu. 5. Press 2 to add a zone. A zone will be added. The system will assign the next available zone number. Options for this zone can now be programmed through the Zone Edit sub-menu. Up to 125 zones can be used. 7.3.
Model 5700 Installation and Operation Manual 7.3.4 View Zone Points To view the points in a zone, follow these steps: 1. Press to display the main menu. or 2. Enter the installer code if requested. 3. Select 7 for Program Menu. Display reads: Initializing Please wait . . . 4. Press 2 to enter zone menu. 5. Press 4 to view zone points. 6. Enter the number of the zone you wish to view, then press .
Programming 7.4 Group An output group is made up of output points that have been programmed to respond in the same way. Output groups simplify programming because you do not have to program each individual point. Once you have defined the characteristics of output groups, you can assign each point to the appropriate group. Up to 125 output groups can be defined. 7.4.1 Edit Group In the edit group option you can program the name of an output group (Section 7.4.1.1) and change the properties (Section 7.
Model 5700 Installation and Operation Manual 8. Select the characters for the group name by pressing the character is shown then press . or arrow until the desired OR Enter the Numerical Designator for the character you want, then press . See Appendix B Table B-1 of this manual for a list of available characters and their numeric designators. 9. Repeat step 8 until the name is complete. 10. Press when the name is complete. 7.4.1.
Programming Silencing Options The following silencing options are available for each output group. Table 7-2: Silencing Options Option Description SILENCE Silenceable. The output group can be silenced through the key. NON-SIL Not silenceable. The output group cannot be silenced. Activation of the for this output group. key will be ignored AUT UNSIL Auto Unsilenced. If this option is selected, the output group can be silenced for a programmed timeframe.
Model 5700 Installation and Operation Manual 13. Press the 14. Press or arrows to select the desired latching option. or arrows to select the desired silencing option. Refer to Table 7-2. . 15. Press the 16. Press . 17. Enable group activation for a condition (see Table 7-3) by pressing the select Y (yes) or N (no). 18. Press or arrows to . 19. Repeat steps 14 and 15 for all the activation options. 7.4.2 Add Group To add a group, follow these steps: 1. Press to display the main menu.
Programming 7.4.3 Delete Group 1. Press to display the main menu. or 2. Enter the installer code if requested. 3. Select for Program Menu. 7 Display reads: Initializing Please wait . . . 4. Press 3 to enter group menu. 5. Press 3 to delete a group. A warning screen will display. If you want to proceed with deleting the group, select Yes. To cancel, select No. 7.4.4 View Group Points 1. Press to display the main menu. or 2. Enter the installer code if requested. 3.
Model 5700 Installation and Operation Manual 7.4.5 Edit Output Group Templates Some installations may require that zones be mapped to more than 8 output groups. With output group templates you can combine one or all output groups into one template, which can be used when the same combination of outputs are used for several zones. For example, lets say an installation has five zones (See table below). The check mark indicates what output groups are mapped to each zone.
Programming 7.5 Point You may need to change characteristics of individual input points (detectors and switches) even after using JumpStart. This section explains how to change options for: type of input point; latching/non-latching status (switches); and name and zone assignment of a point. 7.5.1 Point Programming For SLC To program for points, follow these steps: 1. Press to display the main menu. or 2. Enter the installer code if requested. 3. Select for Program Menu.
Model 5700 Installation and Operation Manual 9. Select the type of device by pressing the or heading "Type Selection" for a list of choices. arrows. Refer to Table 7-4 under column Table 7-4: Point Programming Module Type Type Selection Function Latching Option Comments UNUSED PHOTO ION HEAT PHOT DUCT DETECTOR SUP DET ION DUCT 2WIRE SMK SUP PHOTO Latching SUP ION Non Latching Use this switch type for manual pull stations. This input is always latched.
Programming Table 7-4: Point Programming Module Type Type Selection Function Latching Option Comments System-level switch provides an alternate way to reset the system; same effect as pressing the Reset key. RESET Positive acknowledge switch. This switch must be used in zones programmed as Positive Alarm Sequence (see Table 7-1). If an acknowledge switch closes when an alarm or trouble condition is not already in progress, a trouble will occur.
Model 5700 Installation and Operation Manual 7.5.2 Point Programming For Internal or External Power Module (5496) To program for an internal or external power module points, follow these steps: 1. Press to display the main menu. or 2. Enter the installer code if requested. 3. Select for Program Menu. 7 Display reads: Initializing Please wait . . . 4. Press to enter point menu. 4 5. Press the choices. 6. Press or arrows to select the desired module. Refer to Section 6.5 for available . 7.
Programming 16. Repeat Steps 1 through 15 for all circuits. Choices Function Selections for each Type Type Selections Comments Enter Point or Circuit UNUSED B NOTIF A NOTIF Select Type AUX PWR CONSTANT Constant auxiliary power. RESETTABLE Resettable auxiliary power. DOOR Door holder auxiliary power. Select Group Group or Zone selection will appear depending on the type selected. Edit Name See Section 7.2.1.1. 7.5.
Model 5700 Installation and Operation Manual 10. Press . 11. Press the 12. Press or arrows to select the desired Group. . 13. Edit module name. See Section 7.5.3.1. Or Press to skip module name edit. 14. Repeat Steps 1 through 13 for all points. 7.5.3.1 Assigning a Name to a Points You can assign a name to a point to make it easier to recognize on a display. If you wish to edit the name of a point, follow these instructions: 1. Do steps 1 through 4 of Section 7.5.3. 2.
Programming 7.6 System Options This section of the manual explains how to customize software options that affect general operation of the system. This includes such items as: AC loss hours, system clock options, holidays schedule, telephone and reporting account options. Refer to each individual subsection for complete instructions. 7.6.1 Reporting Account Up to four reporting accounts can be used with the control panel. Events in accounts are reported by zone.
Model 5700 Installation and Operation Manual 7.6.1.1 Edit Accounts 6. From the next menu, select 1 for Edit Account. A screen similar to one shown in Figure 7-12 will display. The following subsections describe the options on each field. Figure 7-12 Reporting Account Editing Screen Select Account (ID) The control panel provides up to 4 reporting accounts. The priority of an account is based on its account ID. Account 1 is highest priority; Account 4 is lowest.
Programming Events to Report The next six options select which types of events (or event families) will be reported to this account. (See Figure 7-12 for location of these options on the screen.) Events are reported by zone. Event Family Events Included in this Family Alarms All alarms (Water Flow, Manual Pull, Detectors, Auxiliary Switches) Alarm Restore All alarm restores. Supervisory, Trouble, Enable/ Disable Point All trouble and supervisory conditions and trouble and supervisory restores.
Model 5700 Installation and Operation Manual The following special characters are available: Table 7-5: Special Dialing Characters # Pound (or number) key on the telephone * Star key on the telephone , Comma (character for 2-second pause) Use the number buttons on the annunciator or the up- and down-arrow keys to select special characters. Characters begin displaying after "9". See Figure 7-12 for an example. 7.6.1.2 Auto Test Time To access the automatic dialer test time screen: 1.
Programming 5. Select 2 for the phone lines menu. 6. Select the phone line to be edited (1 or 2) by pressing the or arrow, then press . Figure 7-13 Phone Lines Editing Screen 7.6.2.1 Dialing Prefix Enter up to 8 characters to be used for such things as PBX dial-out codes, a pause, and so on.
Model 5700 Installation and Operation Manual 7.6.2.3 Dial Option (TouchTone or Pulse) 9. Press the or arrow to select the dial option, then press Dial Option . Description PULSE If this option is selected, only pulse dialing will be used for this phone line. TT TouchTone dialing. If this option is selected, only TouchTone dialing will be used for this phone line. TT/PL TouchTone alternating with pulse. If this option is selected, the dialer will first attempt to use TouchTone.
Programming 7.6.2.7 Answering Machine Bypass This option is used in conjunction with the Silent Knight Software Suite 5660. This feature ensures that an answering machine will not interfere with communication between the panel and the computer. If an answering machine is used at the panel site, enable this feature; if an answering machine is not used, disable the feature. This option is factory-programmed as Yes (enabled).
Model 5700 Installation and Operation Manual 7.6.3.1 Trouble Events You can map certain system trouble events to an output group. To access the screen for selecting output groups and cadence patterns for system trouble events. 6. Press 1 for Trouble Events. A screen similar to the one in Figure 7-14 will display. Select a group and a cadence pattern for each event as needed for your application. The U: field is for a user-specified trouble condition.
Programming 7.6.3.2 System Alarm Cadence Fire drill and system auxiliary alarm events can have special cadence patterns to distinguish them from other types of alarms. See Section 7.3.1.4 for available cadence patterns. A typical use of the System Aux1 and Aux2 patterns is to distinguish fire emergencies from other types of emergencies. For example, you could use one pattern for fire drills and a different pattern for severe weather conditions.
Model 5700 Installation and Operation Manual 7.6.4 Miscellaneous Options 1 Through this programming option you can set the water flow delay time, low AC report delay, enable or disable automatic daylight savings time adjustment, clock format, and AC clock frequency. 7.6.4.1 Water Flow Delay You can program a delay of 0-90 seconds (zero means no delay) to be used in conjunction with a water flow switch. The delay is system-wide. All water flow switches on the system will use the same delay period.
Programming 7.6.4.2 Low AC Report Delay Note: You must select 1-3 hours in UL central station installations and UL remote signaling installations. You can adjust the number of hours before a Low AC report will be sent to the central station. To program low AC report delay, follow these steps: Note: Steps continued from step 6 of Section 7.6.4.1. Low AC Report Delay in Hours (00 - 30) Figure 7-17 Low AC Report Delay Programming Screen 7.
Model 5700 Installation and Operation Manual 7.6.5 Miscellaneous Options 2 Through this programming option you can turn the strobe synchronization during silence feature On or Off, and select the control panel to report events by zone or by point. To edit miscellaneous options 2: 1. Press to display the main menu. or 2. Enter the installer code if requested. 3. Select 7 for Program Menu. Display reads: Initializing Please wait . . . 4. Select 5 for System Options. 5.
Programming 7.6.6 Miscellaneous Options 3 From Miscellaneous Options 3, you set the alarm verification time and set the start and end week and month of Daylight Saving Time. Note: For UL installations the alarm verification time can not be less than 60 seconds. 1. Press or to display the main menu. 2. Enter the installer code if requested. 3. Select 7 for Program Menu. Display reads: Initializing Please wait . . . 4. Select 5 for System Options. 5. Select 7 for Miscellaneous Options 3. 7.6.6.
Model 5700 Installation and Operation Manual 7.6.7 Edit Banner Message The banner is the message that displays on the panel LCD when the system is normal, that is, when no alarms or troubles exist and no one is currently using system menus. You can create a customized message, which can be up to 40 characters, two lines of 20 characters each. If you do not create a customized message, the system will use the internal banner. You cannot change the internal banner.
Programming 7.7 JumpStart Autoprogramming IMPORTANT! JumpStart is intended to be used prior to performing any custom programming. Each time JumpStart is executed, all options will be reset to their default values. Do not run JumpStart after you have configured the system through programming. To run JumpStart: 1. Press to display the main menu. or 2. Enter the installer code if requested. 3. Select for Program Menu. 7 Display reads: Initializing Please wait . . . 4. Select for System Options.
Model 5700 Installation and Operation Manual 7.8 Computer Account An installer at the panel site can initiate communications between the panel and a computer running the SK Fire System Editor (see also Section 8.3.15). In order for this communication to function properly both the computer (running the software) and the control panel must have matching computer account numbers and computer access codes.
Programming 7.9 Access Codes Access codes provide the user access to the control panel functions. Each access code can be customized for each user. This allows some users the ability to access programming and other higher level panel functions, while other users may only need access to lower level functions such as preforming fire drills, or acknowledging trouble conditions. Profile 1 is the profile that dictates what functions the Fire Fighter Key has access to.
Model 5700 Installation and Operation Manual To change an access code: 1. Press or to display the main menu. 2. Enter the installer code if requested. 3. Select 7 for Program Menu. Display reads: Initializing Please wait . . . 4. Select 8 for System Options. Display reads: Select Profile 01 Fire Fighter’s Key 5. Select the access code you wish to edit by pressing the 6. Then press 7.9.1 or arrow. .
Section 8 System Operation Operation of the control panel is simple. Menus guide you step-by-step through operations. This section of the manual is an overview of the operation menus. Please read this entire section carefully before operating the panel. Press to view Main Menu: Select the desired menu option. Enter your access code if prompted. Note: See Section 7.9 for information on how to modify user access code profiles. Default Codes: User Code (factory-programmed as 1111).
Model 5700 Installation and Operation Manual 8.1.2 Banner The banner is the message that displays on the control panel when the system is in normal mode (no alarm or trouble condition exists and menus are not in use). You can create a customized message that will display instead of the internal (default) message. See Section 7.6.7 for information on customizing the banner. Figure 8-2 Banner Display Examples 8.2 Menu System The control panel is easy to operate from Main Menu.
System Operation 8.2.1 Main Menu Overview The chart below is a brief overview of the Main Menu. These options are described in greater detail throughout this section of the manual. Main Menu Options 8.2.2 Description 1 System Tests From here both menus can access Fire Drill and Indicator Test. 2 Point Functions From here both menus can enable / disable points. 3 Event History Display event history on the LCD. See Section 8.3.3 for more information.
Model 5700 Installation and Operation Manual 8.3.2 Disable / Enable a Point 1. From the Main Menu, select 2. Select 1 2 for Point Functions. for Disable/Enable Point. A list of modules displays. 3. Use and to move through the list. Press to select the module where the point you want to disable/enable is located. A description of the point should display. The fourth line of the screen should show "NORMAL" (meaning that the point is currently enabled) or "DISABLED" (the point is currently disabled).
System Operation 8.3.5 Conduct an Indicator Test The indicator test checks the annunciator LEDs, PZT, and LCD display. 1. From the Main Menu, press 1 for System Tests. 2. Press 2 for Indicator Test. The system turns on each LED several times, beeping the PZT as it does so. At the same time it scrolls each available character across the LCD. A problem is indicated if any of the following occurs: • An LED does not turn on; • You do not hear a beep; • All four lines of the LCD are not full.
Model 5700 Installation and Operation Manual 8.3.7 Conduct a Dialer Test 1. From the Main Menu, press 1 for System Tests. 2. Select 5 for Dialer Test. The screen will display “Manual dialer test started”. When the test is completed, you will be returned to the . 8.3.8 Silence alarms or troubles Press and enter your code or rotate the key at the prompt. If an external silence switch has been installed, activating the switch will silence alarms or troubles.
System Operation 5. A screen similar to those shown in Figure 8-3 will display. Figure 8-3 Checking Detector Sensitivity Compliance If a printer is attached to the system (via a Module 5824 Serial/Parallel Interface), you can print detector status (see Section 8.3.16). 8.3.11 View Status of a Point 1. From the Main Menu, select 2 for Point Status. 2. From the list that displays, press to select the module where this point is located.
Model 5700 Installation and Operation Manual 8.3.15 Communicating with a Remote Computer An installer at the panel site can initiate communications between the panel and a computer running the Silent Knight Software Suite. You can use this feature to upload a panel configuration. For example, if you have made programming changes to an installation on site using an annunciator, you can send your changes to the computer, so that the central station will have the latest data about the installation.
System Operation 8.3.16 Working with a Printer If you are using the Model 5824 Serial/Parallel Interface, several printing options are available. See Section 4.6 for information about installing the 5824. 1. From the Main Menu, select 5 Printer Options. 2. From the next screen, select the 5824 module where the printer is connected. 3. If the printer is not currently busy printing another report, a screen with the following options will be available. If the printer is busy, a message will display.
Model 5700 Installation and Operation Manual 8.4 Operation Mode Behavior The control panel can be in one of seven conditions at any given moment: Normal, Alarm, Prealarm, Supervisory, Trouble, Silenced, and Reset. Table 8-2 describes the behavior of the panel in each of these modes. Table 8-2: Operation Modes of FACP Operation Mode Normal Occurs When System Behavior In This Mode You Can No alarm or SYSTEM POWER LED is on.
System Operation Table 8-2: Operation Modes of FACP Operation Mode Trouble Occurs When System Behavior A system trouble The dialer seizes control of the phone line condition and calls the central station. occurs. The on-board annunciator sounds a loud, pulsing beep in the sequence one second on, nine seconds off. In This Mode You Can Press (down arrow) to view the trouble. A screen similar to this one displays. SYSTEM TROUBLE LED flashes. The LCD displays a screen similar to this one.
Model 5700 Installation and Operation Manual 8.5 Releasing Operations This control panel supports two types of releasing, Double Interlock Zone, and Single Interlock Zone. The Double Interlock Zone operation requires an interlock switch input in the system, and the Single Interlock does not. An interlock switch is typically a dry-contact pressure switch. Important! These releasing functions can only be done if the system has a 5496 intelligent power module included.
System Operation 8.5.1 Single Interlock Zone Releasing A single interlock zone utilizes a minimum of two addressable detectors, and a designated manual release switch. Important! Only addressable detectors can be used. No conventional detectors can be used. Each Single Interlock Zone input requires at least one manual release switch. Conditions Required for an Pre-Alert Output Activation If any single addressable detector is activated, the "Pre-Alert" output will activate.
Model 5700 Installation and Operation Manual 8.5.2 Double Interlock Zone Releasing A Double Interlock Zone uses a minimum of two Addressable detectors, a designated manual release switch, and an interlock switch input. An interlock switch is typically a dry-contact pressure switch and will be referred to as an interlock/pressure switch in this document. Important! Only addressable detectors can be used. No conventional detectors can be used.
System Operation 8.6 Smoke Alarm Verification Figure 8-5 illustrates how the Smoke Alarm Verification cycle operates. Figure 8-5 Smoke Verification Cycle During the Confirmation Period if there is no alarm indication then the system will return to normal operation.
Model 5700 Installation and Operation Manual 8-16 151295
Section 9 Reporting This section lists receivers that are compatible with this control panel, and the reporting codes sent by the control panel for SIA and Contact ID formats. 9.1 Receivers Compatible with the Control Panel Table 9-1 shows receivers compatible with the control panel.
Model 5700 Installation and Operation Manual SIA Reporting Format Event Description Local programming aborted or ended with errors Event Family Event Class (System, Zone, or Point) Module ID # (if any) SIA Event Code Parameter (if any) Contact ID Reporting Format Qualifier Event Code Group # Contact # 000 Trouble System Event LU 1 628 00 Periodic test event – normal Test System Event RP 1 602 00 000 Periodic test event – off normal Test System Event RY 1 608 00 000 Initial
Reporting SIA Reporting Format Contact ID Reporting Format Event Family Event Class (System, Zone, or Point) Supervisory condition restore Trouble Zone Event SR Zone 3 Supervisory condition Trouble Zone Event SS Zone 1 Water flow switch trouble Trouble Zone Event ST Zone 1 Supervisory/Tamper switch trouble Trouble Zone Event ST Zone Zone-based AUX1 switch alarm Alarm Zone Event UA 1000+Zone Zone-based AUX2 switch alarm Alarm Zone Event UA System-based AUX1 switch alarm
Model 5700 Installation and Operation Manual SIA Reporting Format Event Description Event Family Event Class (System, Zone, or Point) Module ID # (if any) SIA Event Code Parameter (if any) Contact ID Reporting Format Qualifier Event Code Group # Contact # Water flow switch alarm Alarm Point Event pi Exp. ID SA Pnt # 1 113 Exp. ID Pnt # Water flow switch disabled Disable Point Event pi Exp. ID SB Pnt # 1 571 Exp.
Section 10 Testing and Troubleshooting 10.1 Troubleshooting This section of the manual offers suggestions for troubleshooting hardware problems. Please read this section if you encounter a problem when installing the control panel. If these suggestions do not solve your problem or if you encounter a problem that is not listed here, contact Silent Knight Technical Support at 800-328-0103 for assistance. 10.
Model 5700 Installation and Operation Manual Problem Possible Cause / Suggested Actions The panel indicates a ground fault trouble An earth ground fault occurs when the panel senses an unexpected flow of condition (trouble message "GROUND current from one or more of its terminals to the earth connection (Terminal 2). FAULT" displays). Isolate the wiring that is causing the fault by removing wiring connections one at a time until the earth fault is no longer present.
Testing and Troubleshooting 10.3 Built-in Troubleshooting and Testing Tools The fire control panel has several built-in testing and troubleshooting tools that can be utilized to save time while testing and troubleshooting points and SLC devices. 10.3.1 SLC Device Locator SLC device locator can be used to locate a device on a SLC loop. Follow these steps to locate a particular SLC device: 1. Select 2 (Point Functions) from the Main Menu. 2. Select 4 (SLC Dev Locator).
Model 5700 Installation and Operation Manual 10.3.2 SLC Multi Locator This feature is the same as SLC Device Locator, except you can locate up to 8 devices on a single search. Follow these instructions to locate multiple SLC devices: 1. Select 2 (Point Functions) from the Main Menu. 2. Select 5 (SLC Dev Locator). A message similar to the one shown in Figure 10-1 will display. Figure 10-2 Shut Down Warning 3. Press the or arrow to toggle NO to YES then press .
Testing and Troubleshooting 10.3.3 I/O Point Control This feature allows you to toggle any output on or off and trip any input device. This can be useful to test a point’s output mapping. Follow these steps to control a I/O point: 1. Select 2 (Point Functions) from the Main Menu. 2. Select 6 (I/O Point Control). 3. Select the Module the point is on. 4. Enter the zone number , or press the then press 5. Press or arrow to select the point you wish to test, .
Model 5700 Installation and Operation Manual 10-6 151295
Section 11 Installation Records This section of the manual is for you to use if you wish to track of how points, zones, and groups have been programmed. 11.1 Detector and Module Point Record You can use Table 11-1 to keep track of module and sensor points.
Model 5700 Installation and Operation Manual 11-2 151295
Appendix A Compatible Devices A.1 Notification Appliances For proper operation, you must use polarized devices with a Model 7628 4.7k ohm EOL resistor on each loop. All supervised notification appliances used with the control panel must be polarized. Note: Not all devices can use the Sync feature, be sure to check Table A-1 to ensure the device you have chosen will work with this feature. This control is UL listed for panel wide Synchronization.
Model 5700 Installation and Operation Manual Table A-1: Compatible Notification Appliances Manufacturer Model 2824 Faraday (cont.
Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Faraday (cont.
Model 5700 Installation and Operation Manual Table A-1: Compatible Notification Appliances Manufacturer FCI (cont.
Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Model Audio Type GES-24-30 Strobes GES-24-60 Strobes GES-24-75 Strobes GES-24-110 Strobes GES-24-15/75 Strobes GES-24-177 Strobes GES3-24 Multi Candella Strobe Multi Candella Strobe GESR-24 GEH-24 Gentex (cont.
Model 5700 Installation and Operation Manual Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual P1224MC Horn/Strobe P1224MCK Horn/Strobe P1224MCP Horn/Strobe P1215 Horn/Strobe P121575 Horn/Strobe P121575K Horn/Strobe P121575W Horn/Strobe P1215W Horn/Strobe P2R 2-Wire Horn/Strobe P2RH 2-Wire Horn/Strobe High Candela P24110 Horn/Strobe P24110A Horn/Strobe P24110K Horn/Strobe P
Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual PC2430W Horn/Strobe PC2475 Horn/Strobe PC2475W Horn/Strobe PC2495 Horn/Strobe PC2495W Horn/Strobe P2415 Horn/Strobe PS1224MCW Horn/Strobe PS1224MCSP Horn/Strobe PS1224MCPW Horn/Strobe PS2415ADA Mini-Horn/Strobe PS241575ADA Mini-Horn/Strobe PS24110ADA Mini-Horn/Strobe PS2475ADA Mini-Horn/Strobe S1215 Strobe S1215W Strobe
Model 5700 Installation and Operation Manual Table A-1: Compatible Notification Appliances Manufacturer Model Audio Strobe SC241575W Strobe SC241575P Strobe SC241575PW Strobe SC24177 Strobe SC24177W Strobe SC2430 Strobe SC2430W Strobe SC2475 Strobe Strobe SC2495 Strobe SC2495W Strobe SCR Ceiling Strobe SCRH Ceiling Strobe High Candela SR Wall Strobe SRH Wall Strobe High Candela SS24110ADA Strobe SS2415ADA Strobe SS2475ADA
Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual AMT-24MCW 151295 Horn/Strobe AH-24WP-R Horn AMT-12\24-R Strobe Horn AMT-24-LS-VFR Strobe Horn AMT-24-LSM-VFR Strobe Horn AS-241575W Horn/Strobe AS-24MCC Horn/Strobe AS-24MCCH Horn/Strobe AS-24MCW Horn/Strobe AS-24MCWH Horn/Strobe ASWP-2475W Horn/Strobe AS-24MCW-FR Strobe Horn AS-24MCW-FW Strobe Horn AS-2415W-FR Strobe Horn A
Model 5700 Installation and Operation Manual Table A-1: Compatible Notification Appliances Manufacturer Wheelock (cont.
Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Wheelock (cont.
Model 5700 Installation and Operation Manual Table A-1: Compatible Notification Appliances Manufacturer Wheelock (cont.) Model Visual Type MIZ-24-WH-VF-W Mini-Horn/Strobe MIZ-24-WM-VF-W Mini-Horn/Strobe MT-12/24-R Strobe Horn MT-24-LS-VFR Strobe Horn MT-24-LSM-VFR Strobe Horn MT-24-MS-VFR Strobe Horn MT-24-IS-VFR Strobe Horn MT-24-SL-VFR Strobe Horn MT-24-SLM-VFR Synch.
Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Wheelock (cont.) A.
Model 5700 Installation and Operation Manual A.3 Two-Wire Smoke Detectors Table A-2 lists two-wire smoke detectors that are compatible with the fire control panel. The table is organized by manufacturer. The columns show the number of detectors per loop that can be used. 5700 24H Identifier Operating Voltage Range 18.5–27.4 VDC Note: The maximum number of smoke detectors per zone is determined by both the current draw and the impedance of the smoke detector.
Compatible Devices Table A-2: Compatible Two-Wire Smoke Detectors Manufacturer Model Name or Number (Base model name or number in parentheses.
Model 5700 Installation and Operation Manual A-16 151295
Appendix B Special Characters Lists This section contains tables of programmable characters that may be used for device, module, and zone names or phone numbers. B.1 Characters used for Naming Table B-1 list the available character and their associated numeric designator. When programming these numbers can be entered as a short cut to using the up or down arrow keys, to select characters when naming a point or zone.
Model 5700 Installation and Operation Manual B-2 151295
Silent Knight Fire Product Warranty and Return Policy General Terms and Conditions • All new fire products manufactured by Silent Knight have a limited warranty period of 18 months from the date of manufacture against defects in materials and workmanship. See limited warranty statement for details. • This limited warranty does not apply to those products that are damaged due to misuse, abuse, negligence, exposer to adverse environmental conditions, or have been modified in any manner whatsoever.
• • The defective board must be returned within 30 days of shipment of replacement board for customer to receive credit. No credit will be issued if the returned board was damaged due to misuse or abuse.
Model 5700 Basic Operating Instructions These Instructions must be framed and displayed next to the 5700 panel in accordance with NFPA 72 fire code for Local Protected Fire Alarm Systems. Test the system in accordance to NFPA 72. Refer to Installation Manual P/N 151295. Operation Task to Perform Silence Alarms and Troubles Press then enter a code if prompted. Silence LED will light. Reset Alarms Press then enter a code if prompted. Press then enter a code if prompted.
Cut Along the Dotted Line
7550 Meridian Circle Maple Grove, MN 55369-4927 763-493-6455 1-800-328-0103 Fax: 763-493-6475 © 2006 Silent Knight
