V25 Series ArmorDome™ CCTV Camera User Guide
Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview The unobtrusive, low-profile design of the V25 ArmorDome™ CCTV Camera is ideal for indoor and outdoor installations in commercial and residential venues. Before You Begin Please read this guide carefully before you install the V25 ArmorDome CCTV Camera. Keep this guide for future reference. WARNING! The use of CSA Certified/UL Listed Class 2 power adapters is required to ensure compliance with electrical safety standards.
Initial Setup Before installing the V25 Camera, you must first: • • Disassemble the camera. Set up the camera for mounting on a wall or a ceiling. Disassembling the Camera To disassemble the camera: 1. Use the security hex key provided to remove the three #6-32 x 3/8 in. machine screws securing the V25 front plate and dome to the base (see Camera Components). Set aside the screws. Use a Phillips screwdriver to remove the two #6-32 x 1/4 in.
Wall Mount Setup When the V25 Camera is mounted on a wall, the camera carrier can be adjusted to pan and tilt. Once you have disassembled the camera, prepare the camera for mounting on a wall: 1. 2. Use a pair of side-cutters to remove the perforated square in the gimbal support bracket (see Wall Mount Setup). Discard this square. This allows full motion of the camera gimbal. Use a Phillips screwdriver and two #6-32 x 1/4 in.
Ceiling Mount Setup When the V25 Camera is mounted on the ceiling, the camera carrier can be adjusted to rotate and tilt. Once you have disassembled the camera, prepare the camera for mounting on a ceiling: 1. Remove both arms from the gimbal support bracket by holding the end of the arm and bending it back and forth until it breaks off (see Figure 3). Do not remove the center square from the gimbal support bracket. Use a Phillips screwdriver to remove the two #6-32 x 1/4 in.
Figure 3 Ceiling Mount Setup Showing Electrical Isolation of Line Lock Camera Carrier Nylon bushing Insulating washer Gimbal #6-32 x 1/4 in. machine screw Camera and carrier #6-32 x 3/8 in.
Installation The V25 Camera is designed to be flush mounted on a panel or in a standard deep double-gang electrical box. The camera can be located indoors or outdoors, on a wall or ceiling, in accordance with the current Electrical Code or any national wiring rules that apply. Follow the Initial Setup procedure before installing the V25 Camera. Mounting the Camera on a Wall or Ceiling To mount the V25 Camera on a wall or ceiling panel: 1.
Mounting the Camera in an Electrical Box To mount the V25 Camera in an electrical box: 1. 2. Install the V25 in the electrical box (see Figure 5). Secure the camera in place with the four #6-32 x 3/4 in. plated steel, Phillips head machine screws provided. Figure 5 Electrical Connections (Electrical Box) Standard deep double-gang electrical box Pan axis must be vertical for wall mount installation TOP (picture) label must be on top of lens mount Video output: female BNC #6-32 x 3/4 in.
2. Install a male BNC connector on the video cable coming from the video monitor or CCTV system. Connect the video cable to the female BNC connector and cable coming from the base of the V25 Camera. Connect the AC or DC power wires to the red and black wires coming from the base of the V25 Camera, as shown in Figure 5. 3. 4. WARNING! The use of CSA Certified/UL Listed Class 2 power adapters is required to ensure compliance with electrical safety standards.
Changing the Quick Change Lens Some V25 Cameras have a quick change lens mount, designed to provide a fast and easy way to change the camera lens. To change the quick change lens: 1. 2. Remove the quick change lens: a. Turn the lens holder 45° counterclockwise (see Figure 6). b. Pull the lens holder out of the lens mount. Install a new quick change lens: a. Insert the lens holder into the lens mount.
Dip Switch Functions (Color Cameras) Color Camera Switch Settings GAMMA AE FLON BLC IRIS N/U * AGC MAX AWB1 AWB2 AWB3 Figure 7 * N/U = Not used. Leave in Off position. Push lock ON OFF 1 2 3 4 5 6 7 8 9 10 Not used Line lock adjustment Factory (default) settings Fixed lens camera ON = ON (up) OFF 1 2 3 4 5 6 7 8 9 10 10 Document 920.0090 Rev 3.
Adjustment Method (Color Cameras) Switch no. 1 2 3 4 5 6 7 Function Off On GAMMA AE (Automatic Exposure) FLON (Flicker Less) BLC (Backlight Compensation) IRIS Not used AGC Off (0.45) Off Off Off On (1.
Manually Setting Shutter Speed (Color Cameras) To manually set the shutter speed, turn switch #2 to the ON position; then set switch #3, #4, and #5 for the desired shutter speed (see Figure 7).
Dip Switch Functions (Monochrome Cameras) 2 AGC 1 FLON BLC Monochrome Camera Switch Settings IRIS Figure 8 ON OFF 3 4 5 Not used Line lock adjustment Factory (default) settings = ON (up) ON = OFF (down) OFF 1 2 3 4 5 Adjustment Method (Monochrome Cameras) Switch no.
Adjusting the Line Lock (Vertical Phase) for 24 VAC Operation In multiple camera installations, wire all cameras to the same phase. This will ensure that the vertical phase of all cameras are aligned. Phase adjustment may be necessary to prevent picture roll when switching between cameras. Note If the phase cannot be adjusted to prevent picture roll, reverse the power polarity.
Replacing the Dome If the polycarbonate dome is damaged or scratched beyond use, contact your distributor or salesperson to order a V25 Dome Replacement Kit. To replace the V25 dome: 1. 2. 3. 4. 5. Use the security hex key (provided) to remove the three #6-32 5/8 in. machine screws securing the V25 plate and dome to the base (see Figure 9). Put aside. Use a Phillips screwdriver to remove the three #6-32 1/4 in. machine screws that attach the dome retainer plate to the front plate.
Solving Common Technical Issues No Video ❐ Check that the power supply voltage is within the operating specifications for your camera model. See Specifications for details. ❐ Connect a video monitor directly to the V25 video output cable to eliminate video problems that could be caused by other equipment such as video switches. ❐ Check the video connections to the monitor or CCTV system. ❐ Check the camera connections to the V25 power supply. Fuzzy Video ❐ Check the video ground connections.
Service Subject to the terms and conditions listed on the Product Warranty Card, during the warranty period Silent Witness will repair or replace, at its sole option, free of charge, any defective products returned prepaid. In the event you have a problem with any Silent Witness product, please call Custmer Service for assistance or to request a Return Authorization (RA) number. In the U.S.A. and Canada, call 1.800.893.9513. Or call +1.604.574.1523.
Specifications Note Specifications apply to all camera models, unless noted otherwise. Video Specifications Pickup device: Electronic iris: Surge protection: Video output impedance: Video signal: Monochrome Color Resolution: Monochrome Color Signal to noise ratio: Monochrome Color Sync system: Light sensitivity: Monochrome 1/3 in. CCD 1/60 (1/50) to 1/100,000 seconds 1.
Size and Weight Diameter x height x diameter above surface: Diameter x height overall: 4.7 in. x 3.4 in. x 4.7 in. (119 mm x 86 mm x 119 mm) 6 in. x 33/4 in. (152 mm x 95 mm) 1.8 lbs. (816 g) Weight: Electrical Box Requirements Indoor or outdoor, deep, double-gang electrical box: Length x width x depth: 3 3/4 in. x 3 in. x 3 1/2 in. (95 mm x 76 mm x 89 mm) Four #6-32 mounting holes: 3.3 in. x 1.8 in.
Cable Guidelines Maximum Power Supply Cable Length (feet/meters) Cameras With AC/DC Power Supplies Total load 2.5 W 2.5 W 3.5 W 3.5 W Power supply 15 VDC 24 VAC 15 VDC 24 VAC 24 AWG 260/79 608/185 60/18 470/143 Wire gauge 22 AWG 18 AWG 415/126 980/299 100/30 760/232 1055/322 2515/767 250/76 1926/587 16 AWG 1680/512 3930/1198 400/122 3065/934 Note Calculations are based on an unregulated linear power supply, which would be the worst case.
Mounting Template 46.0 mm 1.81" 40.0 mm 1.57" 83.5 mm 3.29" Please do not remove this page. Photocopy if necessary.
V25 Model Numbers V25B21036 Typical V25 model number Lens Options: 029 036 060 080 120 Size mm 2.9 3.6 6.0 8.0 12.0 Viewing Horiz. 90º 74º 42º 32º 22º Angle Vert. 67º 55º 32º 24º 17º F-stop 2.0 2.0 2.2 2.2 2.0 Camera Options: B1 B21 B6 B26 C1 C21 C6 C26 Monochrome (EIA) Monochrome (CCIR) High resolution monochrome (EIA) High resolution monochrome (CCIR) Color (NTSC) Color (PAL) High resolution color (NTSC) High resolution color (PAL) Note Some combinations of options are not available.
Regulatory Compliance FCC Statement (U.S.A.) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. Industry Canada Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
www.silentwitness.com Toll free: 1.888.289.2288 International: 00800.2020.8080 Silent Witness Enterprises Ltd. Sales: 1.888.289.2288 Tech Service:1.800.893.9513 Phone: 1.604.574.1526 Fax: 1.604.574.7736 Email: swsales@silentwitness.com 6554 - 176th Street Surrey, B.C. V3S 4G5 Canada Document 920.0090 Rev 3.00 April 16, 2002 Specifications subject to change without notice. Imperial conversions are approximate.
