INTELLIKNIGHT® MODEL 5700 Addressable Fire Alarm Control Panel Installation and Operations Manual Document 151295 10/30/14 Rev: S P/N 151295:S ECN: 14-0724
Installation Procedure Installation Precautions - Adherence to the following will aid in problem-free installation with long-term reliability: WARNING - Several different sources of power can be connected to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit and associated equipment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized.
Contents Contents Section 1 Introduction .............................................................................................................................................. 1-1 1.1 Overview of Basic System ........................................................................................................1-1 1.1.1 Hardware Features ............................................................................................................1-1 1.1.2 Software Features .........................
Contents 4.1.3.2 Dead Front Removal ................................................................................................4-2 AC Connection .........................................................................................................................4-3 Battery Connection ...................................................................................................................4-4 4.3.1 RBB Accessory Cabinet ......................................................................
Contents Section 5 SK and SD SLC Device Installation 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 List of SK SLC Devices ............................................................................................................5-1 List of SD SLC Devices ............................................................................................................5-2 Maximum Number of Devices ..................................................................................................
Model 5700 Installation Manual 7.3 7.4 7.5 7.6 7.7 Zone .........................................................................................................................................7-3 7.3.1 Edit Zone ............................................................................................................................7-3 7.3.1.1 Edit Zone Name .......................................................................................................7-4 7.3.1.2 Edit Zone Properties ......
Contents 7.8 7.9 Computer Account ..................................................................................................................7-32 Access Codes ........................................................................................................................7-33 7.9.1 Profile Edit Menu ..............................................................................................................7-34 7.9.1.1 Edit Name ..............................................................
Model 5700 Installation Manual Section 9 Reporting 9.1 9.2 ..................................................................................................................................................... 9-1 Receivers Compatible with the Control Panel ..........................................................................9-1 Reporting Formats Table ..........................................................................................................
151295 Section 1 Introduction The 5700 Fire Alarm Control / Communicator is an addressable fire control system that meets the requirements of UL 864. 1.1 1.1.1 Overview of Basic System Hardware Features • The 5700 has one signaling line circuit (SLC) that supports 50 SK detectors and 50 SK modules or 50 SD protocol devices. • 2.5A of output power is available through 2 sets of terminals for notification appliance circuits or auxiliary applications.
Introduction 1.1.2 151295 Software Features • Advanced smoke detector features: –Automatic drift compensation –Maintenance alert region –Point status meets calibrated smoke test requirements for NFPA 72 • “JumpStart” feature for easy programming • Non-volatile event history stores 1000 events • A choice of output patterns available for notification outputs, including ANSI 3.41 temporal signal • Built-in synchronization appliance support for Faraday, Gentex®, Wheelock®, or System Sensor ® 1.
Model 5700 Installation and Operation Manual 1.3 Compatible Products The chart below lists the products available from Silent Knight for use with the 5700. Table 1-2 5700 Compatible Products Type of Device Model Description SK Addressable SLC Devices See Section 5.1 for a list of compatible devices. SD Addressable SLC Devices See Section 5.2 for a list of compatible devices.
Introduction 151295 The following modems have been tested by Silent Knight for compatibility with the 5700 and the Silent Knight Software Suite software packages: Table 1-3: Compatible Modems Manufacturer US Robotics Model 28.8 Lifestyle Motorola 28.8, 3400 series Premier 33.6 Multi-Tech 1.4 MT19321ZDX How to Contact Silent Knight If you have a question or encounter a problem not covered in this manual, contact Silent Knight Technical Support at 800-446-6444.
Model 5700 Installation and Operation Manual operation of kitchen appliances. In addition, dusty or steamy environments may cause a smoke detector to falsely alarm. If the location of a smoke detector causes an abundance of false alarms or nuisance alarms, do not disconnect the smoke detector; call a professional to analyze the situation and recommend a solution.
Introduction 151295 Requirements and Recommendations include: • Smoke Detectors shall be installed in sleeping rooms in new construction and it is recommended that they shall also be installed in sleeping rooms in existing construction. • It is recommended that more than one smoke detector shall be installed in a hallway if it is more than 30 feet long. • It is recommended that there shall never be less then two smoke detectors per apartment or residence.
1295 Section 2 Agency Listings, Approvals, and Requirements Install and maintain in accordance with NFPA 72. Detector spacing shall be in accordance to NFPA 72. End-of line relays and resistors shall be placed within the electrical box located and the end of the initiating circuit. Testing and maintenance should be performed according to NFPA 72. 2.
Agency Listings, Approvals, and Requirements 151295 that is also compliant. See installation instructions for details. d) The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0).
Model 5700 Installation and Operation Manual • • • • 151295 applications, and hotel/motel room applications. The system allows the Alarm Verification time to be set from 1 to 255 seconds. For UL certified installations the setting must be a maximum of 60 seconds. Call forwarding shall not be used. When two count is used detector spacing shall be cut in half, you shall not use the alarm verification feature, and no delay shall be used. P.A.
151295 Section 3 Before You Begin Installing This section of the manual is intended to help you plan your tasks to facilitate a smooth installation. Please read this section thoroughly, especially if you are installing a 5700 panel for the first time. 3.1 What’s in the Box? The 5700 ships with the following hardware: • • • • • A cabinet with all hardware assembled Two keys for the front door Installation and Operation manual P/N 151295 Ten 4.
Before You Begin Installing 3.3 151295 Electrical Specifications Table 3-1 list the terminal block on the 5700 as well as a description of the each individual terminal and their respective electrical rating. For location of the terminals refer to Figure 3-2. See also Section 4 for installation. Table 3-1: Terminal Descriptions and Electrical Specifications Label Rating Terminal No.
Model 5700 Installation and Operation Manual 3.4 151295 Wiring Specifications Induced noise (transfer of electrical energy from one wire to another) can interfere with telephone communication or cause false alarms. To avoid induced noise, follow these guidelines: • Isolate input wiring from high current output and power wiring. Do not pull one multi-conductor cable for the entire panel.
Before You Begin Installing 3.5 151295 Board Assembly Diagram On-board Annunciator 120 VAC, 60 Hz, 1.5A AC Power Input Form C Relays Programming Port Terminal Block 1 Battery Connector 24 VDC Terminal Block 2 Phone Lines SLC In/Out, SLC Programming NAC/Aux Power Circuits SBUS Connections Form C Trouble Relay Figure 3-2 Model 5700 Assembly Figure 3-2 shows the circuit boards, and annunciator.
Model 5700 Installation and Operation Manual 3.6 151295 Calculating Current Draw and Standby Battery This section is for helping you determine the current draw and standby battery needs if you are using SK addressable devices (Table 3-2) or SD addressable devices (Table 3-3). 3.6.1 Current Draw Worksheet Requirements The following steps must be taken when determining 5700 current draw and standby battery requirements. 1.
Before You Begin Installing 3.6.2 151295 Current Draw Worksheet for SK SLC Devices Use Table 3-2 to determine current requirements during alarm/battery standby operation when SK SLC devices are installed. (Copy the page if additional space is required.) You can install up to 50 SK detectors and 50 SK modules.
Model 5700 Installation and Operation Manual 151295 Table 3-2: Current Calculation Worksheet for SK Devices Device # of Devices Aux Pwr SK-Zone (50 max.)1 SLC Aux Pwr SK-Zone-6 Standby Current Current per Device Standby: 12 mA mA mA Alarm: 90 mA mA mA Standby/Alarm: .27 mA mA mA Standby: 50 mA mA mA 270 mA mA mA 2 mA mA mA Standby: .
Before You Begin Installing 151295 Table 3-2: Current Calculation Worksheet for SK Devices # of Devices Device Standby Current Current per Device B Auxiliary Devices Current Notification Appliance Circuits Refer to device manual for current rating. Alarm: mA mA Alarm: mA mA mA mA Alarm: C mA Notification Appliances Current D Total current ratings of all devices in system (line A + line B + C) E Total current ratings converted to amperes (line D x .
Model 5700 Installation and Operation Manual 151295 Table 3-3: Current Calculation Worksheet for SD Devices Device # of Devices (50 max.)1 SD500-ANM Aux. Pwr SLC (50 max.) SD500-LED 1 Aux. Pwr SLC (50 max.)1 SD500-SDM Standby Current Current per Device Aux. Pwr SLC Standby: 8 mA mA Alarm: 60 mA Standby/Alarm: .55 mA mA Standby: 10 mA mA Alarm: Alarm Current mA 220 mA mA mA LED: 10 mA mA mA Standby/Alarm: .
Before You Begin Installing 151295 Table 3-3: Current Calculation Worksheet for SD Devices # of Devices Device Standby Current Current per Device Alarm/Standby: B mA Alarm Current mA mA Auxiliary Devices Current Notification Appliance Circuits Refer to device manual for current rating.
Model 5700 Installation and Operation Manual 3.7 151295 Installation Tasks Overview This section provides a chart listing tasks that need to be performed when installing the IntelliKnight 5700 system. The chart is intended to be a handy way for you to make sure you have completed all necessary tasks. Unless noted, these tasks do not have to be performed in the order they are listed here. Important: Connect and address SLC devices before running JumpStart. See Sec. (for more info.
Before You Begin Installing 151295 See Sec. (for more info.) Task JumpStart automatically selects some options for SLC devices (see “JumpStart” section of this chart). You can change options selected by JumpStart, if necessary and further customize input point options. Select device type SK or SD). Only one device type can be used per control panel. 7.2 Program type of switch (manual pull, fire drill, and so on), if necessary. (JumpStart assigns all switches as Manual Pull type.) 7.
151295 Section 4 Control Panel Installation Caution! To avoid the risk of electrical shock and damage to the unit, power should be OFF at the control panel while installing or servicing. 4.1 Mounting the Control Panel Cabinet Read the environmental specifications in Section 3.2 before mounting the 5700 panel. The 5700 cabinet dimensions are: 12¾” W x 15-1/8” H x 3-3/8” D (32.39 cm W x 38.42 cm H x 8.57 cm D).
Control Panel Installation 151295 4.1.3.1 Installing the Dead Front Follow these steps to properly install the dead front panel into the control panel cabinet. 1. Remove the top two annunciator screws, do not discard them they will be reused. See Figure 4-1 for annunciator screw location. 2. Set the dead front into the cabinet as shown in Figure 4-1. 3. Reinsert the two annunciator screws as shown in Figure 4-1. Dead Front Panel Figure 4-1 Dead Front Installation and Removal 4.
Model 5700 Installation and Operation Manual 4.2 151295 AC Connection At installation, connect the AC terminals to the power source as shown in Figure 4-2. It may be necessary for a professional electrician to make this connection. The AC terminals are rated at 120 VAC, 60 Hz, 1.5A.
Control Panel Installation 4.3 151295 Battery Connection The control panel battery charge capacity is 7.0 to 35 AH. The main control cabinet can house batteries up to 7 AH, larger capacity batteries can be housed in a Remote Battery Box (P/N RBB). See Section 4.3.1 for deteails.Use 12V batteries of the same AH rating. Determine the correct AH rating as per your current load calculation (see Section 3.6). Maximum battery charging current 3.1 Amps. Wire batteries in series to produce a 24-volt equivalent.
Model 5700 Installation and Operation Manual 4.3.1 151295 RBB Accessory Cabinet The Model RBB Accessory cabinet can be used when your backup batteries requirements use backup batteries that are too large to fit into the main control panel cabinet. The RBB cabinet holds batteries up to the 35 AH size. The RBB dimensions are 16" W x 10" H x 6" D (40.64 cm W x 25.4 cm H x 15.24 cm D). 4.3.1.
Control Panel Installation 3. 151295 Run extended battery cable from control panel cabinet through conduit to RBB cabinet. See Figure 4-6. RBB Cabinet Cover Screws Conduit Coupler Conduit - + + - RBB Cabinet Cover Screws Figure 4-6 Battery Connections in the RBB Cabinet Note: Figure 4-6 is an example of how the wire connections can be routed.
Model 5700 Installation and Operation Manual 4.4 151295 SBUS Wiring This section contains information on calculating SBUS wire distances and the types of wiring configurations (Class B). 4.4.1 Calculating Wiring distance for SBUS modules The following instructions will guide you in determining the type of wire and the maximum wiring distance that can be used with control panel SBUS accessory modules.
Control Panel Installation 151295 Note: The following formulas were used to generate the wire distance chart: 6.0 Volts Maximum Resistance (Ohms) = Total Worst Case Current Draw (amps) Maximum Resistance (Ohms) Maximum Wire Length (Feet) = (6000 feet maximum) Rpu * 500 where: Rpu = Ohms per 1000 feet for various wire gauges (see table below) Table 4-2: Typical Wire Resistance Per 1000 ft. Using Copper Wire Wire Gauge Ohms per 1000 feet (Rpu) 22 16.2 18 6.4 16 4.02 14 2.
Model 5700 Installation and Operation Manual 4.4.2 151295 Wiring Configurations Figure 4-8 illustrates Class B configuration. Supervised Power Limited Figure 4-8 SBUS Class B Wiring 4.4.2.1 How to Power SBUS Devices From Auxiliary Power Supply Figure 4-9 illustrates how to power SBUS devices from an Auxiliary Power Supply such as the 5495 or 5499, when the maximum number of SBUS devices exceeds the SBUS power requirements.
Control Panel Installation 4.5 151295 5860emote Annunciator Installation The optional Model 5860 Remote Annunciator, shown in Figure 4-10, performs the same functions as the onboard annunciator as well as initiate and end fire drills with a single key press and view event history by alarms, supervisories, or troubles. Up to 8 annunciators can be added to the 5700 system. Figure 4-10 Model 5860 Remote Annunciator, Front View 5860 installation involves the following steps: 1.
Model 5700 Installation and Operation Manual 4.5.1 151295 Mounting the 5860 This section of the manual describes mounting the remote annunciator. The annunciator can be flush- or surfacemounted. Figure 4-11 shows the parts of the annunciator. Instructions for disassembling and mounting appear on the following pages.
Control Panel Installation 151295 The 5860 comes from the factory fully assembled. You must disassemble it for mounting. To disassemble the annunciator, use a 5/64 hex wrench to remove the set screws, located on the bottom of the annunciator bezel. (See Figure 4-12 for location of the set screws.) Holes for surface mounting. Knockout holes Stand-off (throughout) Holes for inserting wires for flush mounting (located in all corners). Screw for placement of mounting wires (top and bottom).
Model 5700 Installation and Operation Manual 151295 4.5.1.1 Flush Mounting This section of the manual describes flush mounting. You can flush-mount with or without an electrical box. Flush Mounting with an Electrical Box The 5860 annunciator can be used with the following types of electrical boxes: 4S, single-gang, and doublegang. If an electrical box is used, the box must be 1-3/8” back from the face of the wall to accommodate the annunciator.
Control Panel Installation 4. 151295 After the annunciator wiring to the panel has been completed (described in Section 4.5.2), replace the electronic assembly in the back box. Place the bezel over the back box and tighten the set screws on the bezel. Attach second set of wires to top of back box. Secure the wires behind this screw. Insert wires at an angle into the first holes past the sheet rock. Figure 4-14 Flush Mounting the Back Box 4.5.1.
Model 5700 Installation and Operation Manual 4.6 151295 5824 Serial/Parallel Printer Interface Module Installation The 5824 serial/parallel printer interface module allows you to connect a printer to the panel, so you can print a real-time log of system events, a report of detector status, and event history. 5824 installation involves the following steps: 1. Make sure power is off at the panel. 2. Connect the 5824 to the panel as shown in Figure 4-16. Note: Two 5824s per panel maximum. 3.
Control Panel Installation 4.6.1 151295 Selecting 5824 Options Configuring the 5824 includes the following steps: • • • Add the module to the system. JumpStart will add the module automatically (see Section 6.1). You can also add it manually (see Section 7.2.2). Select a name, if desired (see Section 7.2.1.1). Select options for the printer and the output port. See below. Printer and Output Port Options 1. From the Main Menu, select 7 for Program Menu. 2. Select 1 for Module. 3.
Model 5700 Installation and Operation Manual 4.7 151295 5880 LED Driver Module The 5880 is an LED driver board that can be used in a wide variety of applications, including as an interface with most customized floor plan annunciator boards. The 5880 can drive up to 40 LEDs and has one PZT controller. The 5880 also has eight inputs for dry contact monitoring. The following sub-sections describe hardware installation. Refer to Section 6 for programming information. 4.7.
Control Panel Installation 4.7.2 151295 FACP Connection The 5880 connects to the panel via the SBUS. Make connections as shown in Figure 4-20. After the 5880 is connected to the panel, it must be added to the system. This programming step is described in Section 4.9.
Model 5700 Installation and Operation Manual 4.7.3 151295 LED Wiring There are four 12-pin connectors on the 5880 board for connecting LEDs. Each LED gets its power from Pin 11. Internal resistors are sized so that there is approximately 10 mA of current for each LED, no series resistors are required. LED outputs can be mapped to output circuits. See Section 6 for programming details. Wire the LEDs as shown in Figure 4-21.
Control Panel Installation 151295 inputs. Supervised Model 7628 4.7k EOL Figure 4-22 Dry Contact Wiring 4.8 5865-3 / 5865-4 LED Annunciator Installation The 5865-3 and 5865-4 are LED annunciators. The 5865-4 has 30 mappable LEDs, remote silence and reset key switches, and a general system trouble LED. The 5865-3 has 30 mappable LEDs only. These are arranged as 15 pairs of red (typically used for alarm) and yellow (typically used for trouble) LEDs. Installation of the 5865-3 and 5865-4 is identical.
Model 5700 Installation and Operation Manual 4.8.1 151295 FACP Connection The 5865 connects to the panel via the SBUS. Make connections as shown in Figure 4-24. After the 5865 is connected to the panel, it must be added to the system. This programming step is described in Section 4.9. Supervised Power Limited Figure 4-24 5865 Connection to the FACP 4.8.2 5865 Mounting Mount the 5865-4 to a standard 4-gang electrical box. Mount the 5865-3 to a standard 3-gang electrical box.
Control Panel Installation 151295 illuminated. Figure 4-26 Inserting Zone Description Labels 4.9 Configuring Modules This section describes how to configure any system hardware modules that have been added to the system. 4.9.1 Assigning Module IDs When installing a hardware module (such as, 5824, 5860, 5496, 5865-3 or 5865-4), you must use the DIP switches on the module to assign an ID# to the module. Figure 4-27 shows all possible DIP switch positions and their correlation to a numerical ID.
Model 5700 Installation and Operation Manual 151295 4.10 Telephone Connection Connect the telephone lines as shown in Figure 4-28. The Model 7860 phone cord is available from Silent Knight for this purpose. A number of programmable options are available for customizing telephone lines. These options are described in Section 7.6. Supervised Figure 4-28 Connection of Telephone Lines 4.
Control Panel Installation 151295 4.11.1.1 Class B Notification Wiring You must use an appliance from the list of compatible appliances in the Appendix A at the back of this manual. To install a Class B notification appliance circuit: 1. Wire Class B Notification appliances as shown in Figure 4-29. 2. Configure the circuit through programming (see Section 7.5).
Model 5700 Installation and Operation Manual 151295 4.11.1.2 Class A Notification Wiring You must use an appliance from the list of compatible appliances in the Appendix at the back of this manual. To install a Class A notification appliance circuit: 1. Wire the Class A notification appliances as shown in Figure 4-30. Caution For proper system supervision do not use looped wire under terminals marked – and + of the Flexput connectors. Break wire runs to provide supervision of connections. 2.
Control Panel Installation 4.11.2 151295 Auxiliary Power Installation NAC Circuits 1and 2 on the control panel can be used as auxiliary power circuits. The four types of auxiliary power available are: • • • • Door Holder (see section 4.11.2.1) Constant (see section 4.11.2.2) Resettable Power (see section 4.11.2.3) Sounder Sync Power (see Section 4.11.2.4) Auxiliary power circuits are power limited. Each circuit can source up to 2.5A (total current for system must not exceed 2.5A).
Model 5700 Installation and Operation Manual 151295 4.11.2.2 Constant Power Use constant power for applications that require a constant auxiliary power source. Power is always present at Constant circuits. 4.11.2.3 Resettable Power Resettable power is typically used to power beam detectors, flame detectors and conventional 4-wire smoke detectors. For circuits selected as Resettable, 27.4 volt power is always present at the terminals unless a system reset occurs.
Control Panel Installation 151295 4.13 Remote Station Applications 4.13.1 Keltron Model 3158 Installation The control panel is compatible with Keltron Model 3158, used for direct connection to a Keltron receiver. The 3158 reports alarms, supervisories, and troubles. The 3158 is intended for connection to a polarity reversal circuit of a remote station receiving unit having compatible ratings. The steps for connecting the 3158 to the control panel.
Model 5700 Installation and Operation Manual 4.13.2 151295 City Box Connection Using the 5220 Module This section describes how to connect the control panel to a municipal fire alarm box or “city box” as required by NFPA 72 Auxiliary Protected Fire Alarm systems for fire alarm service. The city (master) box is an enclosure that contains a manually operated transmitter used to send an alarm to the municipal communication center which houses the central operating part of the fire alarm system.
Control Panel Installation 4.13.3 151295 NFPA 72 Polarity Reversal 4.13.3.1 Using the 5220 Module When the 5220 is wired and programmed for polarity reversal, it reports alarm and trouble events to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset. If an alarm condition occurs, the alarm relay will close, overriding the trouble condition.
Model 5700 Installation and Operation Manual 151295 4.13.3.2 Using the 7644-L8 Module When the 7644-L8 is used for polarity reversal, it allows alarm and trouble events to be reported to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset. To install the 7644-L8 for polarity reversal: 1. Wire the 7644-L8 to the control panel as shown in Figure 4-36.
Control Panel Installation 151295 Wire the SD500-ARM as shown in Figure 4-37. Intended for Connection to a Polarity Reversal Circuit of A Remote Station Receiving Unit Having Compatible Rating.
Model 5700 Installation and Operation Manual 4.13.5 151295 Using a MR-201/T Control Relay From Air Products When the MR-201/T control relay is wired for polarity reversal, it reports alarm and trouble events to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset. If an alarm condition occurs, the alarm relay will close, overriding the trouble condition. Current: 15 mA max.
Control Panel Installation 4.13.6 151295 Transmitter Activated by Dry Contacts This section describes the connection of a UL 864 listed remote station transmitter to the 5700 FACP dry contacts. The FACP contacts must be supervised by the remote station transmitter module using end-of-line resistors (ELRs) with a value determined by the transmitter manufacturer. Power is also provided by the remote station transmitter manufacturer.
151295 Section 5 SK and SD SLC Device Installation Caution! To avoid the risk of electrical shock and damage to the unit, power should be OFF at the control panel while installing or servicing. 5.1 List of SK SLC Devices The following SK SLC devices can be used with the control panel. See the device installation instructions for more information (packaged with the device). Note: The control panel supports the use of either SK SLC devices or SD SLC devices.
SK and SD SLC Device Installation SK Part Number 151295 Model Name/Description Section/ Install Sheet PN B210LP 6" mounting base B224BI 6" isolator base I56-0725-00 B224RB 6" relay base I56-3737-00 B200SR 6" temporal sounder base I56-3392-00 B200S Intelligent Sounder Base I56-3387-00 B501 4" mounting base I56-0357-00 B200SR-LF Low Frequency Sounder Base I56-4152-00 B200S-LF Low Frequency Sounder Base I56-4151-00 5.
Model 5700 Installation and Operation Manual 5.3 151295 Maximum Number of Devices The 5700 supports SK or SD devices on one5700ystem. The maximum number of devices per system varies depending on device protocol. Device support is as follows: • SK Devices–A 5700 system can support a total of 50 SK detectors and 50 SK modules. OR • SD Devices–A 5700 system can support a total of 50 SD SLC detectors and modules, in any combination. 5.
SK and SD SLC Device Installation 151295 The following figures show how length is determined for out and back tap and T-Tap style wiring. Figure 5-1 Calculating wire run length for a simple out and back When using T-taps, the total length of all taps and the main bus must not exceed 40,000 feet. This requirement must be met in addition to the maximum distance requirements for the various wire gauges.
Model 5700 Installation and Operation Manual 5.4.2 151295 Wiring SLC Devices in Style 6 & 7 (Class A) Configuration The following figure illustrates how to wire the SLC loop for Style 6 or Style 7 Class A installations. Note: Style 6 does not use short circuit isolator devices. Figure 5-3 Class A SLC Configuration Note: No t-taps allowed on class A SLC loops. Caution For proper system supervision do not use looped wire under terminals marked SLC + and – of the SLC device connectors.
SK and SD SLC Device Installation 5.5 151295 SK Detector Installation This section describes how to install heat and smoke detectors. All detectors ship with installation instructions. Refer to the detector’s installation instructions for more detailed information.
Model 5700 Installation and Operation Manual 5.6 151295 Addressing SK SLC Devices All SK devices are addressed using the two rotary dials that appear on the device board. Use the ONES rotary dial to set the ones place in a one or two digit number, and use the TENS rotary dial to set the tens place in a two digit number. SK device addresses are handled differently than SD device addresses. The control panel recognizes when an SK detector or SK module is installed.
SK and SD SLC Device Installation 5.7 151295 SD Detector Installation The information in this section applies to the following SD models: SD505-AHS Heat Detector, SD505-AIS Ionization Smoke Detector, and SD505-APS Photoelectric Smoke Detector. 5.7.1 Wiring SD Detectors 1. Wire device bases as shown in Figure 5-6. 2. Set the address for each device as described in Section 5.8.
Model 5700 Installation and Operation Manual 5.8 151295 Addressing SD SLC Devices This section tells how to address detectors and modules. 5.8.1 SD505-APS, SD505-AHS, & SD505-AIS The SD505-APS photoelectric smoke detector, SD505-AHS heat detector, and SD505-AIS ionization smoke detector are easily addressed at the FACP. The Installer Code is required to perform this task. To address a SD505-APS, SD505-AHS, or SD505-AIS: 1.
SK and SD SLC Device Installation 5.8.2 151295 SLC Devices with DIP Switches Input and relay module addresses are set using the DIP switches on the module board. The chart below shows the available addresses. For example, to select address 3, place DIP switches 1 and 2 in the up position. The range of valid addresses is 1-50. 0 is an invalid address.
151295 Section 6 Programming Overview This section of the manual is intended to give you an overview of the programming process. Please read this section of the manual carefully, especially if you are programming the control panel for the first time. The JumpStart feature automates many programming tasks and selects default options for the system. You will run JumpStart at least once when you are installing the system. See Section 6.1 for details.
Programming Overview 151295 output when a supervisory condition occurs. Circuit 4 (Relay 2): Assigned to Group 125. JumpStart automatically programs Zone 1 to activate Group 125 using constant on output when an alarm occurs. Addressable output points (Relay modules): All addressable relay devices will be configured as “Output Pt” (general purpose output point) and assigned to Group 1. Note: Relay output is constant even if the zone activating the relay is programmed with an output pattern. 6.1.
Model 5700 Installation and Operation Manual 6.2 151295 Mapping Overview This section of the manual is an overview of mapping. Details about how to select mapping options appear in the appropriate subsections in Section 7. Mapping is an important concept with the control panel. In general terms, mapping is assigning or linking events to outputs that should activate when events occur.
Programming Overview 6.2.1 151295 Input Point Mapping Input points are assigned to input zones. Any input point can be assigned to any input zone. (Input points can be assigned to one zone only. An input point can be designated as “Unused,” which means it has not been assigned to a zone.
Model 5700 Installation and Operation Manual 6.2.2 151295 Output Circuit Mapping Figure 6-3 is a simple example showing how to assign notification and relay output circuits to groups. For an example of a simple floor above/floor below application, see Figure 6-5.
Programming Overview 6.2.3 151295 Zone Event Mapping There are 11 types of events that can occur in zones (see below). For each event type, you can activate up to 8 output groups and patterns. If it is necessary to map to more than 8 output groups, an output group template may be used (see Section 7.4.5 for information on output group templates).
Model 5700 Installation and Operation Manual 151295 Figure 6-5 Example of Zone Events Mapped to Output Groups and Patterns 6-7
Programming Overview 6.2.4 151295 Mapping LED Points Figure 6-6 is a simple example showing how LED points are mapped to zones and output groups. Typically you would create two output groups for each zone, one for alarms and one for troubles. (LED points are available when Models 5865-3/4 and/or 5880 are used with the system).
Model 5700 Installation and Operation Manual 6.3 151295 Programming Using the 5660 Silent Knight Software Suite You can use the 5660 Silent Knight Software Suite (SKSS) to program the control panel onsite or remotely. SKSS is an optional software package that lets you easily program the control panel using a Windows-based computer and a modem* (not sold by Silent Knight).
Programming Overview 6.4.2 151295 Moving through the Menus Figure 6-7 shows how to move through Menu screens, using the System Options screen as an example. Figure 6-7 Moving through Program Menu 6.4.3 Selecting Options and Entering Data There are several ways to make programming selections using the control panel depending on which screen you are currently using. The chart below is a generic explanation. To Press Select from a menu. Enter the number of the option. Enter numeric data.
Model 5700 Installation and Operation Manual 6.4.4 Editing Keys The keys shown in Figure 6-8 are available for use when you are in the Program Menu.
Programming Overview 6.5 151295 Programming Menu Quick Reference This section of the manual lists all Program Menu options in the order they appear on the sub-menus. Default settings are indicated in text or marked with an asterisk. The comments column provide quick information and a reference to a section (if applicable) which has more detailed information. Menu Options/Defaults Edit Module Select Module Enter Module ID Comments Enter Module Name Edit Module Settings (if applicable) Section 7.2.
Model 5700 Installation and Operation Manual Menu 151295 Options/Defaults Edit Zone Select Zone to Edit Zone Accessry Opt Comments SD Devices. Section 7.3.1.4 Section 7.3.1.5 Cadence 00-16, 23, *02 Fire Cadence 00, 01, *02, 23 CO Cadence 00, 01, 02, *23 SK Devices. Section 7.3.1.4 Section 7.3.1.5 Local Zone Y or *N Section 7.3.1.5 Add Zone Adds next available zone number. Section 7.3.2 Delete Zone Select Zone to Delete Section 7.3.3 View Zone Points Select Zone to View Section 7.3.
Programming Overview Menu 151295 Options/Defaults Comments UNUSED *Latching (LA) or Non-Latching (NL) *Silenceable (SI) or Non-Silenceable (NS) Zone # (*001) PHOTO, ION, HEAT, ACCLIMATE, HEAT HT, PHOTHEAT, BEAM *NO ACCESSORY, SDR BAS, RLY BAS, I-SdrBa Single/Multi Station: *NST, SST, MST Station Silenceable: *SIL, NSL Point Internal and External Sensor Point # 5815XL, SK Devices Accessory Group # (*001) Point Name DETECTOR *Latching (LA) or Non-Latching (NL) *Silenceable (SI) or Non-Silenceable (
Model 5700 Installation and Operation Manual Menu 151295 Options/Defaults Comments *Latching (LA) or Non-Latching (NL) *Silenceable (SI) or Non-Silenceable (NS) Zone # (*001) PHOTO, ION, HEAT,ACCLIMA TE, HEAT HT, PHOT-HEAT, BEAM *NO ACCESSORY, SDR BAS, RLY BAS, I-SdrBa Single/Multi Station: *NST, SST, MST Station Silenceable: *SIL, NSL Accessory Group # (*001) Point (cont.
Programming Overview 151295 Menu Options/Defaults Comments *Latching (LA) or Non-Latching (NL) *Silenceable (SI) or Non-Silenceable (NS) Zone # (*001) Sensor Point # CO FIRE ALRM Fire/ ALRM CO, ALRM Fire/SUPR CO, SUPR Fire/ ALRM CO, SUPR Fire/SUPR CO *NO ACCESSORY, SDR BAS, RLY BAS, I-SdrBa Single/Multi Station: *NST, SST, MST Station Silenceable: *SIL, NSL Accessory Group # (*001) Point Name UNUSED MAN_PULL, PAS_ACK, DETECT SW, MAN REL, ILOCK, CO DET SW Internal and External 5815XL, SK Devices P
Model 5700 Installation and Operation Manual Menu 151295 Options/Defaults Comments AUX CONST, AUX RESET, Point Name AUX DOOR OUTPUT PT Internal and External Module Point # 5815XL, SK Devices RELAY AUX RESET, AUX DOOR DETECTOR 2WIRE SMK Group # (*001) Point Name Section 7.5.1 Point Name *Silenceable (SI) or Non-Silenceable (NS) Zone # (*001) Point Name UNUSED *Latching (LA) or Non-Latching (NL) Point (cont.
Programming Overview Menu 151295 Options/Defaults Comments *Latching (LA) or Non-Latching (NL) *Silenceable (SI) or Non-Silenceable (NS) Zone # (*001) DETECTOR *NO ACCESSORY, PHOT DUCT, ION DCT RLY DUCT Single/Multi Station: *NST, SST, MST Station Silenceable: *SIL, NSL Accessory Group # (*001) Point Name 2 WIRE SMK *Silenceable (SI) or Non-Silenceable (NS) Zone # (*001) Point Name Point (cont.) Internal and External Point # 5815XL, SD Devices *Latching (LA) or Section 7.5.
Model 5700 Installation and Operation Manual Menu 151295 Options/Defaults Comments *NO ACCESSORY, DCT RLY SUP DET Single/Multi PHOT DUCT, ION Station: *NST, SST, MST DUCT Station Silenceable: *SIL, NSL Accessory Group # (*001) Point Name MAN_PULL, PAS_ACK, DET SW, MAN REL, ILOCK, CO DET SW WATERFLOW, SUPERVSY, ZN_AUX1, ZN_AUX2, TAMPER *Silenceable (SI) or Non-Silenceable (NS) Zone # (*001) Point Name *Latching (LA) or Section 7.5.
Programming Overview 151295 Menu Options/Defaults Comments OUTPUT PT RELAY AUX RESET, AUX DOOR Internal and External Point # 5815XL, SD Devices Group # (*001) Point Name Point Name UNUSED, NOTIF SLC LED LED # (01-80) Group # (*001) Point Name UNUSED B NOTIF NOTIF OUT, CTRL CKT Group # (*001) A NOTIF NOTIF OUT, CTRL CKT Group # (*001) AUX PWR CONSTANT, AUX RESET, AUX DOOR, AUX SYNC MAN _PULL, PAS_ACK, MAN REL, ILOCK Point (cont.
Model 5700 Installation and Operation Manual Menu 151295 Options/Defaults Comments Zone # (*001) Internal and External Point # Power Supply B SWITCH STATUS PT A SWITCH Same as B SWITCH B DETECT 2WIRE SMK, 4WIRE SMK, *Silenceable (SI) or Non-Silenceable (NS) CO 4WIRE Zone # (*001) Point Name Point Name 4WIRE SMK, *Silenceable (SI) or Non-Silenceable (NS) CO 4WIRE Zone # (*001) 2WIRE SMK, A DETECT Used to activate an ancillary Output Group that does not activate alarm, sound PZT, display
Programming Overview 151295 Menu Options/Defaults Comments *123456 Account # (6-digit number, identifies account to central station) Section 7.6.1.1 Edit Format *CID, S20, SIA Reporting Format (SIA, SIA20, Contact ID) Section 7.6.1.1 Report Alarms Yes (Y), *No (N), or Must (M) Rep.
Model 5700 Installation and Operation Manual Menu 151295 Options/Defaults System Trouble Alarm Silence Trbl Silence Comments Select Group Select Cadence Select Group Select Cadence Select Group Select Cadence None selected None selected None selected Group Tr SBUS Com SBUS Pwr Trouble Events AC Loss System Event Outputs Section 7.6.3.
Programming Overview 151295 Menu Options/Defaults DST *Yes (Enabled) or No (Disabled) System Options DST Start Select week: 1st, Select month *2nd, 3rd, 4th or Last (*Mar) (cont.) DST End Select week: *1st, Select month 2nd, 3rd, 4th or Last (*Nov) Comments Automatic Daylight Saving Time enable or disable. Section 7.6.8.1 Daylight Savings Section 7.6.8.2 Internal Message Edit Banner SLC Family JumpStart AutoPrg Custom Message Edit Line 1 Section 7.6.9 Edit Line 2 SD Section 7.6.
Model 5700 Installation and Operation Manual Menu Options/Defaults 151295 Comments Edit Name Edit Access Code System Reset System Silence System ACK Fire Drill Key System Test Fire Drill Menu Indicator Test Walk Test no Report Walk Test with Report Dialer Test Clear History Buffer Point Functions Access Codes Disable/Enable Point Select Profile (01-20) Panel Functions Point Status Set SLC Device Address SLC Device Locator SLC Mult-Device Locator Profile 1 is the profile that dictates what function
151295 Section 7 Programming This section of the manual describes how to manually program the control panel from the built-in annunciator. Each subsection discusses these menu options in detail. All options described in this section can be performed using the Silent Knight Software Suite 5660. Important! Before any customized programming is done, JumpStart should be run first. After JumpStart is run, thoroughly test the system.
Programming 7.2 151295 Modules This section lists the options available under the module option in the program menu. The types of modules available for the control panel are, 5860 (Keystation) 5824 (Serial/Parallel input/output), 5880 (LED Input/ Output module), 5496 (Intelligent Power Module), and a 5865 (LED Annunciator). 7.2.1 Edit Modules The features that can be edited when this option is selected are, module name, and class of wiring (Class A or Class B).
Model 5700 Installation and Operation Manual 3. Press 1 to enter module menu. 4. Press 2 to add a module. 5. From the next screen, use the screen. or 151295 arrow to choose a module type to add from the The screen will display “Adding module [#]...” for a few moments. You will be returned to the screen where you can select another module if desired. Save changes when you exit the Program Menu or the new module will not be added.
Programming 151295 7.3.1.1 Edit Zone Name 6. To edit the zone name, press 1. A screen similar to the one shown in Figure 7-2 displays. Figure 7-2 Selecting Character for Zone Name 7. Select the characters for the zone name by pressing the or arrow until the desired character is shown then press . Or Enter the Numerical Designator for the character you want, then press . See Appendix B Table B-1 of this manual for a list of available characters and their numeric designators. 8.
Model 5700 Installation and Operation Manual 151295 Alarm Delay Characteristics 3. Select the alarm delay characteristics by pressing the or arrow. Table 7-1 list the delay choices and a description of each. Table 7-1: Alarm Delay Types Type of Delay Description 1-Count One Count (No Delay). When this option is enabled, an alarm occurs immediately when a single device of any of the following types goes into alarm: detector, manual pull, water flow, Aux1 or Aux2.
Programming 151295 Heat Temperature Setting Use this feature to set the temperature at which high temperature detectors will respond. All detectors in the zone will respond in the same way. The range for the SD505-AHS heat detector is from 135°F to 150°F. The range for SK-Heat-HT heat detector is from 135°F to 190°F. The SD505-AHS and SK-Heat-HT heat detectors are absolute temperature devices.
Model 5700 Installation and Operation Manual 8. 151295 Select options for each event that could occur in this zone. Figure 7-4 is a complete example of how you might map a zone. Indicates output group 1, cadence pattern 00 has been selected. 00 is a constant output cadence. See Section 7.3.1.4 for choices. Indicates type of event (in this case, Manual Pull alarm). See Section 6.5 for choices. “T” Indicates output group template 1. See Section 7.4.5 for more information on output group templates.
Programming 151295 7.3.1.4 Cadence Patterns The cadence patterns shown in Figure 7-6 are available for use with the control panel. Cadence patterns can be selected by event type for each zone or for the entire system. Special cadence patterns can be selected for fire drills and any auxiliary system switches used with the system. Figure 7-6 Cadence Patterns Available with the Control Panel Note: When select cadence patterns for alarms, supervisories, or troubles they must be distinctive from each other.
Model 5700 Installation and Operation Manual 151295 7.3.1.5 Zone Accessory Options This option applies to detectors that are used with Sounder bases and Relay bases. Fire Cadence:_ _ / CO Cadence:_ _ (choose from a subset of Patterns 00 to 23). Note: The B200S Sounder bases is intended to be used along with the CO Cadence setting. Local Zone (choose Y (Yes) or N (No). 7.3.2 Add Zone To add a zone, follow these steps: 1. Enter the installer code. 2. Select 7 for Program Menu. 3.
Programming 5. 151295 Enter the number of the zone you wish to view, then press ENTER. Zone Number Module or Device Address Point Number Total Number of Points in the Zone Figure 7-7 View Zone Points Screen 7.4 Group An output group is made up of output points that have been programmed to respond in the same way. Output groups simplify programming because you do not have to program each individual point.
Model 5700 Installation and Operation Manual 151295 7.4.1.2 Edit Group Properties The Edit Group Menu allows you to select options for each group for the following items: 1. Follow steps 1 through 5 of Section 7.4.1. 2. To edit the group properties, press 2. • • • • Latching or non-latching outputs. Silencing operation. Reverse Polarity options. Operation with system switches.
Programming 151295 Silencing Options The following silencing options are available for each output group. Table 7-2: Silencing Options Option Description SILENCE Silenceable. The output group can be silenced through the SILENCE key. NON-SIL Not silenceable. The output group cannot be silenced. Activation of the SILENCE key will be ignored for this output group. AUT UNSIL Auto Unsilenced. If this option is selected, the output group can be silenced for a programmed time-frame.
Model 5700 Installation and Operation Manual 7. Press the or 8. Press ENTER. 9. Enable group activation for a condition (see Table 7-4) by pressing the N (no). 151295 arrows to select the desired silencing option. Refer to Table 7-3. or arrows to select Y (yes) or 10. Press ENTER. 11. Repeat steps 14 and 15 for all the activation options. 7.4.2 Add Group To add a group, follow these steps: 1. Enter the installer code. 2. Select 7 for Program Menu. 3. Press 3 to enter group menu. 4.
Programming 7.4.5 151295 Edit Output Group Templates Some installations may require that zones be mapped to more than 8 output groups. With output group templates you can combine one or all output groups into one template, which can be used when the same combination of outputs are used for several zones. For example, lets say an installation has five zones (See table below). The check mark indicates what output groups are mapped to each zone. You will notice that every zone is mapped to outputs 1 and 2.
Model 5700 Installation and Operation Manual 7.5 151295 Point You may need to change characteristics of individual input points (detectors and switches) even after using JumpStart. This section explains how to change options for: type of point, latching/non-latching, silenceable/ non-silenceable, zone assignment (input points), detector accessory base options, group assignment (output points), and point name. 7.5.1 Point Programming For SLC To program for points, follow these steps: 1.
Programming 151295 Table 7-4: Point Programming Module Type Type Selection Function Latching Option Comments SUP PHOTO DUCT SUP SMOKE PHOTO SUP SMOKE ION SUP HEAT SK SUP DETECTOR SUP ACCLIMATE Latching Non Latching Supervisory switches can be latching or nonlatching. SUP HEAT HT SUP SMOKE PHOTO/HEAT SUP SMOKE BEAM ALRM CO/ ALRM FIRE SUP CO/ALRM FIRE CO SMOKE ALRM CO/SUP DETECTOR FIRE Latching SUP CO/SUP FIRE SLC Loop Non Latching Supervisory can be latching or non-latching.
Model 5700 Installation and Operation Manual 151295 Table 7-4: Point Programming Module Type Type Selection Function SUPERVSY Latching Option Latching Non Latching Comments Use this switch type for tamper monitoring of sprinklers and other fire protection devices. If a contact closes, a sprinkler supervisory event will be generated. Supervisory switches can be latching or non-latching. FIREDRILL System-level, non latching switch. This switch is an alternative way of causing a fire drill.
Programming 151295 Table 7-4: Point Programming Type Selection Module Type Latching Option Function OUTPUT PT SLC Loop (cont.) Select Group Output Point, a general use relay type. Use for applications requiring a relay, such as elevator recall. AUX RESET Use for auxiliary power, resettable applications. See Section 4.11.2.3 to learn how this option operates. AUX DOOR Use for auxiliary power, door holder applications.
Model 5700 Installation and Operation Manual 151295 11. Repeat Steps 1 through 15 for all circuits. Table 7-5 Menu choices for Internal/External Power Modules Choices Type Selections Function Selections for each Type Comments Enter Point or Circuit UNUSED NOTIF OUT CTRL CKT AUX PWR B SWITCH CONSTANT Constant auxiliary power. RESETTABLE Resettable auxiliary power. DOOR Door holder auxiliary power. SOUNDER SYNC Sounder Sync auxiliary power.
Programming 7.5.3 151295 Point Programming For 5880 and 5865 Modules To program for a 5880 or 5865 module points, follow these steps: 1. Enter the installer code. 2. Select 7 for Program Menu. 3. Press 4 to enter point menu. 4. Press the 5. Press ENTER. or arrows to select the desired module. Refer to Section 6.5 for available choices. Figure 7-11 Programming Points Screen for 5880 and 5865 Modules 6. Enter the point number. 7. Press ENTER. 8. Press the 9. Press ENTER. or 10.
Model 5700 Installation and Operation Manual 151295 A screen similar to the one shown in Figure 7-12 displays. Figure 7-12 Selecting Character for Zone Name 6. Select the characters for the point name by pressing the then press . or arrow until the desired character is shown OR Enter the Numerical Designator for the character you want, then press available characters and their numeric designators. 7. Repeat step 6 until the name is complete. 8. Press ENTER when the name is complete. 7.6 .
Programming 151295 each field. Figure 7-13 Reporting Account Editing Screen Select Account (ID) The control panel provides up to 4 reporting accounts. The priority of an account is based on its account ID. Account 1 is highest priority; Account 4 is lowest. Use Account 1 to report the highest priority events. 6. Press the or arrow to select account ID number, then press ENTER. Edit Account Number Enter an up-to-6-digit number for each account to identify the account to the central station.
Model 5700 Installation and Operation Manual 151295 10. Repeat step 9 for all five event report options. For each event family, select M, Y, or N. M(ust) Must Report. Selecting "M" makes this a primary reporting account for this family of events. The dialer MUST report events in this family to this account. Selecting Must makes an account a primary reporting account. The dialer will try to report the event to the primary account until it exceeds the “Switch Attempts” value.
Programming 151295 7.6.1.2 Auto Test Time To access the automatic dialer test time screen: 1. Enter the installer code. 2. Select 7 for Program Menu. 3. From the Program Menu, select 5 for System Options. 4. From the next menu, select 1 for Reporting Account. 5. From the next menu, select 2 for Auto Test Time. 6. Enter the hour you desire the control panel to send an automatic test report (or press the then press ENTER. 7. Enter the minutes (or press the 8.
Model 5700 Installation and Operation Manual 151295 7.6.2.1 Dialing Prefix Enter up to 9 characters to be used for such things as PBX dial-out codes, a pause, and so on. The following special characters are available: # Pound (or number) key on the telephone * Star key on the telephone , Comma (character for 2-second pause) Use the number buttons on the annunciator or the up- and down-arrow keys to select special characters. Characters begin displaying after “9”. See Figure 7-15 for an example. 6.
Programming 151295 10. Select Y (monitor line) or N (don’t monitor line) by pressing the or arrow, then press ENTER. 7.6.2.6 Answering Machine Bypass This option is used in conjunction with the Silent Knight Software Suite 5660. This feature ensures that an answering machine will not interfere with communication between the panel and the computer. If an answering machine is used at the panel site, enable this feature; if an answering machine is not used, disable the feature.
Model 5700 Installation and Operation Manual 151295 Figure 7-16 System Trouble Event Mapping Example 7.6.3.2 System Alarm Cadence Fire drill and system auxiliary alarm events can have special cadence patterns to distinguish them from other types of alarms. See Section 7.3.1.4 for available cadence patterns. A typical use of the System Aux1 and Aux2 patterns is to distinguish fire emergencies from other types of emergencies.
Programming 151295 7.6.4.1 Water Flow Delay You can program a delay of 0-90 seconds (zero means no delay) to be used in conjunction with a water flow switch. The delay is system-wide. All water flow switches on the system will use the same delay period. To access the screen for programming water flow delay, follow these steps: 1. Enter the installer code. 2. Select 7 for Program Menu. 3. Select 5 for System Options. 4. Select 5 for Time Options.
Model 5700 Installation and Operation Manual 9. 151295 Select AMPM (for AM/PM display format) or MIL (for military or 24 hr display format) by pressing the or arrow, then press ENTER. 7.6.4.5 Change AC Line Frequency The panel’s AC line frequency is selectable for 60 Hz or Neither. AC Frequency feature dictates how the control panel will calculate time based on the AC line frequency used in the installation site.
Programming 151295 10. Then press 7.6.5.4 or ENTER. See Section 9 for reporting codes. Single Key Acknowledge When this feature is programmed Y (Yes) allows the user to press the ACK Key and display the oldest unacknowledged event in the system. Pressing ACK again will acknowledge the event, then display the next oldest un-acknowledge event without pressing the 7.6.6 or arrow keys.
Model 5700 Installation and Operation Manual 7.6.7 151295 Edit Banner The banner is the message that displays on the panel LCD when the system is normal, that is, when no alarms or troubles exist and no one is currently using system menus. You can create a customized message, which can be up to 40 characters, two lines of 20 characters each. If you do not create a customized message, the system will use the internal banner. You cannot change the internal banner.
Programming 7.7 151295 JumpStart Autoprogramming IMPORTANT! JumpStart is intended to be used prior to performing any custom programming. Each time JumpStart is executed, all options will be reset to their default values. Do not run JumpStart after you have configured the system through programming. To run JumpStart: 1. Enter the installer code. 2. Select 7 for Program Menu. 3. Select 6 for JumpStart Autoprogramming. 4. Press the 5. Press ENTER. 7.
Model 5700 Installation and Operation Manual 7.9 151295 Access Codes Access codes provide the user access to the control panel functions. Each access code can be customized for each user. This allows some users the ability to access programming and other higher level panel functions, while other users may only need access to lower level functions such as preforming fire drills, or acknowledging trouble conditions. Profile 1 is the profile that dictates what functions the Fire Fighter Key has access to.
Programming 151295 To change an access code: 1. Enter the installer code. 2. 3. Select 7 for Program Menu. Select 8 for Access Codes. Display reads: 4. 5. Select Profile 01 Fire Fighter’s Key Select the access code you wish to edit by pressing the Then press ENTER. 7.9.1 or arrow. Profile Edit Menu From the Profile Edit Menu you can change the users name, access code, and the panel functions that the user will have access to with their code.
151295 Section 8 System Operation Operation of the control panel is simple. Menus guide you step-by-step through operations. This section of the manual is an overview of the operation menus. Please read this entire section carefully before operating the panel. Press ENTER to view Main Menu: Select the desired menu option. Enter your access code if prompted. Note: See Section 7.9 for information on how to modify user access code profiles. 8.1 Default Codes: User Code (factory-programmed as 1111).
System Operation 151295 of the internal (default) message. See Section 7.6.7 for information on customizing the banner. Figure 8-2 Banner Display Examples 8.3 Menu System The control panel is easy to operate from Main Menu. To view the Main Menu press the ENTER or button on the control panel or remote annunciator, then turn the firefighters key clockwise or enter your access code. The Main Menu will appear as shown in Section 8.3.1. Select the desired option.
Model 5700 Installation and Operation Manual 8.3.2 Using the Menus To move through the menus: To select an option: 8.4 151295 and Use previous menu. to move through the options in a menu. Use Enter the number of the option. –OR– Press ENTER if the option appears at the top of the menu (= symbol displays after the option number in this case). Basic Operation 8.4.1 Setting Time and Date 1. From the Main Menu, select 4 for Set Date and Time. 2. Make changes in the fields on the screen.
System Operation 4. 151295 Use and to move through the list. Press ENTER to select the module where the point you want to disable/enable is located. Select the point to disable or enable on the module. A description of the point should display. The fourth line of the screen should show “NORMAL” (meaning that the point is currently enabled) or “DISABLED” (the point is currently disabled). Press to toggle between NORMAL and DISABLE. 8.4.
Model 5700 Installation and Operation Manual 8.4.9 1. 151295 Conduct a Walk Test From the Main Menu, press 1 for System Tests. IMPORTANT! If any alarm verification zones are being used, the user will be asked if they wish to disable alarm verification during walk test. This occurs for either walk test option. 2. Select 3 for Walk Test-No Rpt. The LCD will display “WALK TEST STOPPED” on Line 1 and “ENTER = start test” on Line 3.
System Operation 151295 When a CAL TRBLE condition occurs, the central station receives a detector trouble report (“373” and the zone or point for Contact ID format; “FT” and the zone or point in SIA format). To check sensitivity for an individual detector, follow the steps below. Section 8.4.19 provides instructions for printing the status of all detectors in the system. 1. From the Main Menu, press 2 for Point Functions. 2. Press 2 for Point Status. 3.
Model 5700 Installation and Operation Manual 8.4.15 151295 View Alarms, Supervisories or Troubles When the system is in alarm, supervisory or trouble, you can press supervisories or trouble. 8.4.16 to view the location of an alarm, View System Information Press 8 from the Main Menu to view the panel model and serial number and system version number and date. Press the to return. 8.4.17 Reset dialer From the Main Menu, select 6. The LCD will display “Dialer reset in progress...
System Operation 8.4.19 151295 Working with a Printer If you are using the Model 5824 Serial/Parallel Interface, several printing options are available. See Section 4.6 for information about installing the 5824. 1. From the Main Menu, select 5 Printer Options. 2. From the next screen, select the 5824 module where the printer is connected. 3. If the printer is not currently busy printing another report, a screen with the following options will be available.
Model 5700 Installation and Operation Manual 8.5 151295 Operation Mode Behavior The control panel can be in one of seven conditions at any given moment: Normal, Alarm, Prealarm, Supervisory, Trouble, Silenced, and Reset. Table 8-1 describes the behavior of the panel in each of these modes. Table 8-1: Operation Modes of FACP Operation Mode Normal Occurs When System Behavior SYSTEM POWER LED is on.
System Operation 151295 Table 8-1: Operation Modes of FACP Operation Mode Supervisory Occurs When The system detects a supervisory condition. System Behavior The dialer seizes control of the phone line and calls the central station. The on-board annunciator sounds a loud, pulsing beep in the sequence one second on, one second off. In This Mode You Can Press down arrow to view the supervisory condition. A screen similar to this one displays. SUPERVISORY LED flashes.
Model 5700 Installation and Operation Manual 151295 Table 8-1: Operation Modes of FACP Operation Mode Trouble Occurs When A system trouble condition occurs. System Behavior The dialer seizes control of the phone line and calls the central station. In This Mode You Can Press down arrow to view the trouble. A screen similar to this one displays. The on-board annunciator sounds a loud, pulsing beep in the sequence one second on, nine seconds off. SYSTEM TROUBLE LED flashes.
System Operation 151295 Table 8-1: Operation Modes of FACP Operation Mode Occurs When System Behavior In This Mode You Can Reset The RESET button is pressed followed by a valid code or rotation of the key. All LEDs are on briefly then the LCD displays “ALARM RESET IN PROGRESS”. If the reset process completes normally, the date and time normal mode screen displays. Menus are not available during the reset process. Silenced An alarm or trouble condition has been silenced but still exists.
Model 5700 Installation and Operation Manual 151295 Table 8-2: Approved Releasing Solenoids Manufacturer Asco Part Number Rating T8210A107 24 VDC, 2.5A 8210G207 24 VDC, 2.5A * The Model 7641-L8 Must be located at the solenoid. *When ordering request PN 7641-L8 Figure 8-4 Wiring Configuration for Solenoid Important! Detectors must be installed at 0.7 times the linear spacing as described in NFPA 72. 8.6.
System Operation 151295 Conditions required for an General Alarm and Release Output Activation If two or more addressable detectors, or a manual release switch activate, the “Alarm” and the “Release” outputs will activate. (Also refer to Table 8-3.
Model 5700 Installation and Operation Manual 151295 Conditions Required for a Release Output Activation Any release requires the activation of an interlock switch, and either a manual release switch or 2 activated addressable detectors. When these conditions are met, the “Release” and “General Alarm” outputs will activate, and the “Alert” output will deactivate.
System Operation 8.7 151295 Smoke Alarm Verification Figure 8-5 illustrates how the Smoke Alarm Verification cycle operates. Figure 8-5 Smoke Verification Cycle During the Confirmation Period if there is no alarm indication then the system will return to normal operation.
151295 Section 9 Reporting This section lists receivers that are compatible with this control panel and the reporting codes sent by the control panel for SIA and Contact ID formats. 9.1 Receivers Compatible with the Control Panel The below table shows receivers compatible with the control panel. Manufacturer Model Format Silent Knight Model 9800 SIA and Contact ID Model 9000 (SIA formats) SIA Ademco Model 685 (Contact ID ) Contact ID Sur-Gard SG-MLR2-DG (V. 1.
Reporting 151295 SIA Reporting Format Event Description Local Programming begin Event Family Trouble Module ID # (if any) SIA Event Code LB Parameter (if any) 0 Contact ID Reporting Format Qualifier 1 Event Code 627 Group # 00 Contact # 000 Local Programming ended normally Trouble LS 0 1 628 00 000 Local Programming aborted or ended with errors Trouble LU 0 1 628 00 000 Panel Date has been changed Trouble JD 0 1 625 00 000 Panel Time has been changed Trouble JT
Model 5700 Installation and Operation Manual 151295 SIA Reporting Format Event Description Event Family Voice VBUS Trouble Restore1 Trouble Voice Message Trouble1 Trouble Voice Message Trouble Restore1 Trouble Voice Switch Expander Trouble1 Voice Switch Expander Trouble Module ID # (if any) SIA Event Code Parameter (if any) Contact ID Reporting Format Qualifier Event Code Group # Contact # ER Exp. ID 3 332 00 Exp. ID pi message ID ET Exp. ID 1 332 Messag e ID Exp.
Reporting 151295 SIA Reporting Format Event Family Event Description Module ID # (if any) SIA Event Code Parameter (if any) Contact ID Reporting Format Qualifier Event Code Group # Contact # Water release circuit has been disabled Trouble pi Exp. ID SS Point # 1 203 Exp. ID Point # Water release circuit has been reenabled Trouble pi Exp. ID SR Point # 3 203 Exp.
Model 5700 Installation and Operation Manual 151295 SIA Reporting Format Event Description Event Family Module ID # (if any) SIA Event Code Parameter (if any) Contact ID Reporting Format Qualifier Event Code Group # Contact # Notification Trouble Trouble FT 1000+Group # 1 320 00 Group # Notification Output trouble restore Trouble FJ 1000+Group # 3 320 00 Group # Positive Alarm Sequence acknowledge switch trouble Trouble FT Zone # 1 373 00 Zone # Positive Alarm Sequence a
Reporting 151295 SIA Reporting Format Event Family Event Description Module ID # (if any) SIA Event Code Parameter (if any) Contact ID Reporting Format Qualifier Event Code Group # Contact # Zone-based AUX1 switch trouble restore Trouble UJ 1000+ Zone # 3 373 01 Zone # Zone-based AUX2 switch trouble restore Trouble UJ 2000+ Zone # 3 373 02 Zone # Zone-based AUX1 switch trouble Trouble UT 1000+ Zone # 1 373 01 Zone # Zone-based AUX2 switch trouble Trouble UT 2000+ Zone # 1
Model 5700 Installation and Operation Manual 151295 SIA Reporting Format Event Description Event Family Module ID # (if any) SIA Event Code Parameter (if any) Contact ID Reporting Format Qualifier Event Code Group # Contact # Emergency NAC Trouble Restored1 Trouble pi Exp. ID QJ Point # 3 320 Exp. ID Point # Emergency Control Circuit Trouble1 Trouble pi Exp. ID QT Point # 1 320 Exp. ID Point # Emergency Control Circuit Trouble Trouble pi Exp. ID QJ Point # 3 320 Exp.
Reporting 151295 SIA Reporting Format Event Description Event Family Module ID # (if any) SIA Event Code Parameter (if any) Contact ID Reporting Format Qualifier Event Code Group # Contact # Positive Alarm sequence acknowledge switch trouble Trouble pi Exp. ID FT Point # 1 373 Exp. ID Point # Point Enabled Disable pi Exp. ID FU Point # 3 571 Exp. ID Pnt # Status Point Trouble Trouble pi Exp. ID UT Point # 1 379 Exp.
Model 5700 Installation and Operation Manual 151295 SIA Reporting Format Event Description Event Family Module ID # (if any) SIA Event Code Parameter (if any) Contact ID Reporting Format Qualifier Event Code Group # Contact # Voice Aux Status Switch Disabled1 Disable pi Exp. ID UB Point # 1 580 Exp. ID Point # Voice Aux Status Switch Enabled1 Disable pi Exp. ID UU Point # 3 580 Exp. ID Point # Water flow switch alarm Alarm pi Exp. ID SA Point # 1 113 Exp.
151295 Section 10 Testing and Troubleshooting 10.1 Troubleshooting This section of the manual offers suggestions for troubleshooting hardware problems. Please read this section if you encounter a problem when installing the control panel. If these suggestions do not solve your problem or if you encounter a problem that is not listed here, contact Silent Knight Technical Support for assistance. 10.
Testing and Troubleshooting 151295 Problem 5496 module that has been physically connected to the panel but is not being recognized. 10.2.1 Possible Cause / Suggested Actions Check the status of the 5496 green LED. If it flashes in the pattern .5 sec. on / .5 sec. off, it is likely that the 5496 has not been added to the system through programming. JumpStart will add any 5496s connected to the panel. If you have already run JumpStart, 5496s can be added manually (see Section 4.9).
Model 5700 Installation and Operation Manual 151295 10.3 Built-in Troubleshooting and Testing Tools The fire control panel has several built-in testing and troubleshooting tools that can be utilized to save time while testing and troubleshooting points and SLC devices. 10.3.1 SLC Device Locator SLC device locator can be used to locate a device on a SLC loop. Follow these steps to locate a particular SLC device: 1. Select 2 (Point Functions) from the Main Menu. 2. Select 4 (SLC Dev Locator).
Testing and Troubleshooting 3. Press the or 151295 arrow to toggle NO to YES then press ENTER. If NO is chosen you will exit back to the Point Function menu. If Yes is chosen the system will cease normal operation leaving the premise unprotected. 4. Select the SLC loop. 5. Enter up to 8 SLC addresses for the devices you wish to locate. The LEDs on the selected devices will start flashing. 6. Press the to exit SLC multi-locator function.
151295 Section 11 Installation Records This section of the manual is for you to use if you wish to track of how points, zones, and groups have been programmed. 11.1 Detector and Module Point Record You can use Table 11-1 to keep track of module and sensor points.
151295 Appendix A Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Model x Visual x Horn/Strobe x Strobe SAD24-75110 x Strobe SL24W-75110 x Strobe SL24C-3075110 x Strobe SLB24-75 x Strobe RSD24-153075 x Strobe RSD24-75110 x Strobe SH24W-75110 x x Horn/Strobe SH24W-3075110 x x Horn/Strobe SHB24-75 x x Horn/Strobe SCM24W-153075 x Chimes/Strobe SCM24W-75110 x Chimes/Strobe SCM24C-3075110 x Chimes/Strobe SCM24C-177 x Chimes/Strobe H2
Compatible Devices 151295 Table A-1: Compatible Notification Appliances Manufacturer Faraday (cont.
Model 5700 Installation and Operation Manual 151295 Table A-1: Compatible Notification Appliances Manufacturer Faraday (cont.
Compatible Devices 151295 Table A-1: Compatible Notification Appliances Manufacturer FCI (cont.
Model 5700 Installation and Operation Manual 151295 Table A-1: Compatible Notification Appliances Manufacturer Model WGEC24-75W Gentex (cont.
Compatible Devices 151295 Table A-1: Compatible Notification Appliances Manufacturer System Sensor (cont.
Model 5700 Installation and Operation Manual 151295 Table A-1: Compatible Notification Appliances Manufacturer Model Audio Type AH-12 x Horn AH-24 x Horn AH-12WP x Horn Weatherproof AH-24WP x AMT-241575W x Horn Weatherproof AMT-24MCW x Multi-Tone Horn Strobe x Mutli-Tone Horn Strobe x Multi-Tone Horn Strobe AMT-241575W-NYC x AMT-12/24 x Multi-tone Horn AMT-12/24 NYC x Multi-tone Horn AS-121575W Wheelock Visual x Horn/Strobe NH-12/24 x x Horn AS-241575W x x Horn
Compatible Devices 151295 Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type MTWPA-2475W x x Multitone Horn Strobe MTWPB-2475W x x Multitone Horn Strobe MTWPG-2475W x x Multitone Horn Strobe MTWPR-2475W x x Multitone Horn Strobe MTWPA-24MCCH x x Multitone Horn Strobe ZNH x NS-121575W x x Horn/Strobe NS-241575W x x Horn/Strobe NS-24MCW x x Horn/Strobe NS-24MCC x x Horn/Strobe NS-24MCCH x x Horn/Strobe ZNS-MCW x x Horn/Strobe
Model 5700 Installation and Operation Manual 151295 Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type RSSWPG-24MCCH x Strobe Weatherproof RSSWPR-24MCCH x Strobe Weatherproof RSSWP-2475W x Strobe Weatherproof RSSWP-2475C x Strobe Weatherproof RSSWP-24MCWH x Strobe Weatherproof ZRS-MCWH x Strobe ZRS-24MCC x Strobe ZRS-24MCCH x MB-G6-24 Strobe Motor Bell MB-G10-24 Motor Bell MB-G6-12 Motor Bell Wheelock MB-G10-12 Motor Bell (cont.
Compatible Devices 151295 A.1 Two-Wire Smoke Detectors The below table lists two-wire smoke detectors that are compatible with the fire control panel. The table is organized by manufacturer. The columns show the number of detectors per loop that can be used. 5700 Identifier 24H Operating Voltage Range 18.5–27.4 VDC Note: The maximum number of smoke detectors per zone is determined by both the current draw and the impedance of the smoke detector.
Model 5700 Installation and Operation Manual 151295 Table A-2: Compatible Two-Wire Smoke Detectors Manufacturer Model Name or Number (Base model name or number in parentheses.
151295 Appendix B Special Characters Lists This section contains tables of programmable characters that may be used for device, module, and zone names or phone numbers. B.1 Characters used for Naming Table B-1 list the available character and their associated numeric designator. When programming these numbers can be entered as a short cut to using the up or down arrow keys, to select characters when naming a point or zone.
Silent Knight Fire Product Warranty and Return Policy General Terms and Conditions • • All new fire products manufactured by Silent Knight have a limited warranty period of 36 months from the date of manufacture against defects in materials and workmanship. See limited warranty statement for details. This limited warranty does not apply to those products that are damaged due to misuse, abuse, negligence, exposure to adverse environmental conditions, or have been modified in any manner whatsoever.
Manufacturer Warranties and Limitation of Liability Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer warrants that the Products manufactured by it in its Northford, Connecticut facility and sold by it to its authorized Distributors shall be free, under normal use and service, from defects in material and workmanship for a period of thirty six months (36) months from the date of manufacture (effective Jan. 1, 2009).
Model 5700 Basic Operating Instructions These Instructions must be framed and displayed next to the 5700 panel in accordance with NFPA 72 fire code for Local Protected Fire Alarm Systems. Test the system in accordance to NFPA 72. Operation Silence Alarms and Troubles Reset Alarms Task to Perform Press SILENCE then enter a code if prompted. Silence LED will light. Press RESET then enter a code if prompted. Press ACK then enter a code if prompted.
Cut Along the Dotted Line
Silent Knight 12 Clintonville Road Northford, CT 06472-1610 203-484-7161 Fax: 203-484-7118 www.silentknight.
