SX-SDWAG 802.
© 2008 Silex Technology America, Inc. All rights reserved. September, 2008 Silex Technology America SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS OF THIS PRODUCT FOR A PARTICULAR PURPOSE. Silex shall not be liable for any errors contained in this manual or for any damages resulting from loss of use, data, profits, or any incidental or consequential damages arising from the use of SILEX products or services.
Contents About This User Manual ............................................................................................................................................ 1 Safety Precautions ................................................................................................................................................. 1 Emissions Disclaimer.............................................................................................................................................
About This User Manual This user manual provides detailed specifications, diagrams and additional information required to install the SXSDWAG 802.11a/b/g SDIO module into a product. The intended audiences are the developers and engineers responsible for the integration of the module in another product. Safety Precautions To prevent damage to the SX-SDWAG module’s electronic circuit components, follow established ESD practices and procedures for handling static-sensitive devices.
Chapter 1: Introduction The SX-SDWAG is an 802.11a/b/g radio/baseband module in a standard SDIO form factor. 1a/b/g capabilities in an SDIO card form factor. Designed for wireless local area network (WLAN) applications that require low power consumption, the SX-SDWAG is ideal for battery-operated portable devices in the medical, weights and measures, transportation and other industries. SX-SDWAG features include: • • • • • • • • • • Highly Integrated System for 802.11a/b/g WLAN U.
Chapter 2 Hardware Specifications/Compliance FCC Information FCC ID: N6C-SXDWAG NOTICE In accordance with FCC Part 15, the SX-SDWAG is listed as a Modular Transmitter device. End products that include the SX-SDWAG shall have the words “Contains Transmitter module FCC ID: N6CSXSDWAG” on an exterior label. This equipment complies with Part 15 of the FCC Rules.
while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research.
Specifications Operating environment: Temperature: -40º to +70ºC (-40º to +158ºF) Humidity: 10% to 90% Storage environment: Temperature: -40º to +85ºC (-40º to +185ºF) Humidity: 10% to 90% Supply voltage: 3.3V ± 5% Host interface: SDIO Frequency bands and modulations: IEEE 802.11b IEEE 802.11g IEEE 802.11a Frequency stability 2.
Chapter 3 Installation Installation Requirements The SX-SDWAG must be installed in a device that contains a 9-pin SDIO slot. The SX-SDWAG has FCC modular approval, which can eliminate the need for you obtain FCC Part 15 Subpart C and E (intentional radiation) approvals for your device. In order to use this FCC modular approval for the SX-SDWAG, you must: 1. Include “Contains FCC ID: N6C-SXSDWAG” on the label of your device. 2.
Figure 2 Connecting the Antenna Cable(s) to the SX-SDWAG 4. If your device is subject to significant vibration or other forces, Silex recommends the use of a retaining bracket to prevent the accidental ejection of the card. This bracket can be the Silex 15000192-100 retaining bracket (see figure 3) or an equivalent custom-made bracket. Figure 3 Securing the SX-SDWAG with Optional Bracket 5. Connect the other end of the cable(s) to the antenna(s).
Appendix A Antenna Information Antenna Cable Drawings and Specifications Figure 2 Antenna Cable Assembly Antenna Information Silex Revision A-1 Page 8
Table 1 Electrical Performance Parameter Value Impedance 50 ohms Frequency Range 1 to 6 GHz Working Voltage 500 VAC (rms) maximum Dielectric Withstanding Voltage 1000 VAC (rms) maximum Insulator Resistance 1000 megohms minimum Antenna Drawings and Specifications Figure 28 Antenna Mechanical Drawing Antenna Information Silex Revision A-1 Page 9
Table 2 Electrical Specifications Parameter Page 10 Value Antenna Type Dipole Swivel Antenna Frequency Range 2.4 to 5.8 GHz Impedance 50 Ohms Gain 2.4 GHz < 1.5 dBi 5.825 GHz < 2.1 dBi VSWR ≤ 2.
Appendix B Silex Contact Information Silex Technology America, Inc. www.silexamerica.com Technical Support: support@silexamerica.com Sales: sales@silexamerica.com Tel: (801) 748-1199 8:00 to 5:00 Mountain Time Tel: (866) 765-8761 toll-free Fax: (801) 748-0730 Silex Technology Europe GmbH www.silexeurope.com Tel: +49-2159-67500 Tel: 0800-7453938 German toll free Email: contact@silexeurope.com Silex Technology Beijing, Inc. www.silex.com.cn Tel: +86-10-8497-1430 Email: contact@silex.com.
Page 12 Silex Revision A-1 Contact Information
Revision A-1
Silex Technology America, Inc. www.silexamerica.
