User's Manual
Mechanical Specications
Note: The ground pads on the module’s bottom side must be connected to electrical and
thermal performance.
Pin 1 Identication
On the top side, Milli 5 has a 2D barcode to identify MAC address, part number, and other
key product data that is needed. The pinhole also represents the Pin 1 corner on the Milli 5
assembly. Note: The horizontal ips bottom pins 180°.
Mechanical dimensions and land pattern
22.750
17.500
22.750
11.000
4.250
4.250
19.250
15.750
12.250
8.750
5.250
1.750
23.983
22.000
29.008
19.250
15.750
12.250
8.750
5.250
1.750
A
C
L
C
L
1 2
14
15
28
29
42
43
56
57
61
6569
1.78
1.14
3.00
3.00
1.14
1.78
2.00
2.00
DETAIL A
SCALE 10:1
1 2 3
56
55
54
57
REVISIONS
REV
CHANGE
NUMBER
DESCRIPTION
BY
DATE
01
INITIAL RELEASE
TH
3.28.17
THIS DRAWING HAS BEEN GENERATED BY A CAD SYSTEM. CHANGES SHALL
ONLY BE INCORPORATED AS DIRECTED BY THE DESIGN ACTIVITY.
DO NOT REVISE MANUALLY.
DATE
ENGINEER :
DESIGNER :
MFG. ENGR. :
Q.A. :
PROG. MGMT/MKT :
APPROVALS
THIRD ANGLE PROJECTION
REV.
DWG NO.
CAGE NO.
SIZE
B
SCALE:
DO NOT SCALE DRAWING
UNLESS OTHERWISE SPECIFIED
SILVER SPRING NETWORKS
PROPRIETARY INFORMATION
THIS DOCUMENT IS THE SOLE PROPERTY OF SILVER SPRING NETWORKS. THE RELEASE OF DATA
CONTAINED IN THIS DOCUMENT AND THE REPRODUCTION OF THIS DOCUMENT, IN WHOLE
OR IN PART, WITHOUT THE WRITTEN PERMISSION OF SILVER SPRING NETWORKS ARE PROHIBITED.
INTERPRET DRAWING IAW ASME Y14.100-2000.
•
DIMENSIONING & TOLERANCING IAW ASME Y14.5M-1994.
•
PARENTHETICAL INFORMATION FOR REFERENCE ONLY.
•
DIMENSIONAL LIMITS APPLY AFTER PROCESSES.
•
DIMENSIONS ARE IN
MM
(METRIC)
.
•
TOLERANCES ARE: ANGLES ± 1°
•
2 PLACE DECIMAL ± .13
3 PLACE DECIMAL ± .013
1.6
SURFACE FINISH (AVERAGE)
•
REMOVE ALL BURRS AND SHARP EDGES .25 RAD MAX.
•
CONCENTRICITY MACHINED DIA: .05 FIM
•
MACHINED TOOL MISMATCH .05 MAX.
•
1 2 3 4 5 6 7 8
A
B
C
D
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
230 W Tasman Drive, San Jose, CA 95134
Phone : 1.866.204.0200 Fax : 1.866.776.0015
www.silverspringnetworks.com
T.HUYNH
-
-
-
DOCUMENT, FOOTPRINT, LAYOUT,
MNIC MILLI 5
5:1
SHEET 1 OF 2
-
3/28/2017
800-0251-00
01
DOWNLOADED AND/OR HARDCOPY UNCONTROLLED
30.00±0.13
25.00±0.13
TOP VIEW
3.60
3.20
1.03
0
2X 1.125
2X 2.875
2X 4.625
2X 6.375
2X 8.125
2X 9.875
2X 11.625
2X 13.375
2X 15.125
2X 16.875
2X 18.625
2X 20.375
2X 22.125
2X 23.875
14X 0.750
5X 3.750
2X 8.250
2X 12.500
2X 16.750
5X 21.250
14X 24.250
0
14X 0.750
2X 3.625
2X 5.375
2X 7.125
2X 8.875
2X 10.625
2X 12.375
2X 14.125
2X 15.875
2X 17.625
2X 19.375
2X 21.125
2X 22.875
2X 24.625
2X 26.375
14X 29.250
5X 4.000
2X 9.500
2X 15.000
2X 20.500
5X 26.000
16X 3.00
56X 1.00
PIN 1
PIN 43
PIN 56
PIN 15
PIN 29
PIN 57
PIN 69
BOTTOM VIEW
DIMENSIONS IN MILLIMETERS
TOLERANCES:
0.00 =
.13
0.000 =
.013
REV.
DWG NO.
CAGE NO.
SIZE
B
SCALE:
1 2 3 4 5 6 7 8
A
B
C
D
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
5:1
SHEET 2 OF 2
01
800-0251-00