I-210+ NIC and Meter Labeling Product Requirements Document Number 340-048002 VERSION DATE AUTHOR REVISIONS 1.0 4/13/07 B. Gilbert Initial version 1.1 5/14/07 B. Gilbert Change incorporates EUI-64 addressing Silver Spring Networks – Confidential and Proprietary NIC508 Labeling.
I-210+ NIC and Meter Labeling Product Requirements 1 Introduction The I-210+ NIC is a FCC Part 15.247 compliant device that enables communication between Silver Spring Networks AMI network and the I-210+ family of meters. The NIC transmits in the 902 to 928 MHz, ISM band and transfers data from utility meter to Silver Spring Networks Relays and Gateways. 1.1 References - Guidelines for use of a 64-bit Extended Unique Identifier (EUI-64), IEEE Publication. 2 Meter Labeling 2.
I-210+ NIC and Meter Labeling Product Requirements 2.2 Meter Auxiliary Label or NIC Address Label For radio identification, the I-210+ meter shall have an auxiliary label containing the Silver Spring Networks NIC address presented in text (16 alphanumeric digits) and barcode formats. • • • • • • Bar Code Type = Code 3 of 9 Bar Code Font Size = unknown Font Type = unknown Font Size = unknown Bar Code Label Dimensions = 1.50” x 0.
I-210+ NIC and Meter Labeling Product Requirements 3 NIC Labeling The SSN I-210+ NIC has two labels relevant to meter final assembly and RMA – the FCC & GE Part Number label and the SSN NIC Address label. Both labels are located on the top side of the NIC PCA. The barcode format is Code 3 of 9. Figure 4 is an example of the FCC ID label that can be found in the location indicated in Figure 6. The size of the label is 1.5” x 1.0” inches. The barcode format is Code 3 of 9.
I-210+ NIC and Meter Labeling Product Requirements Figure 7 – Bottom Side of I-210+ NIC PCA SSN Corporate Name SSN Model Number 4 FCC and Government Guidelines Silver Spring Networks NIC FCC ID: OWS-NIC508 IC: 5975A-NIC508 The I-210+ NIC is REQUIRED to be professionally installed by a properly trained technician. Improper installation could void the user’s authority to operate the equipment. The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1.
I-210+ NIC and Meter Labeling Product Requirements NOTE: For FCC compliance, the following text MUST be included in I-210+ and I-210+c meter manuals and user’s guides. The antenna of this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The device should be installed so that people will not come within 20 cm (8 in.) of the antenna. This equipment has been tested and found to comply with Part 15 of the FCC Rules.
I-210+ NIC and Meter Labeling Product Requirements 4.2 Safety Information WARNING!: Severe shock and explosion hazard! Touching energized parts can result in massive equipment damage, and severe injury or death. Short-circuiting energized parts will result in blinding flash and explosion. Opening and closing electrical circuits can also produce dangerous and explosive arc flashes. Involuntary muscular reactions associated with electrical shock may result in other injuries.
I-210+ NIC and Meter Labeling Product Requirements • • • Provide good lighting in the work area. You cannot work safely if you cannot see what you are doing. Report unsafe conditions or defective equipment to your immediate supervisor. Handle material carefully. Lift and carry properly. 4.4 Personal Protective Equipment (PPE) • • • • • Always wear Personal Protective Equipment (PPE), in accordance with OSHA and ANSI standards. Wear eye protection and electrically insulated gloves.
I-210+ NIC and Meter Labeling Product Requirements • • • • • Call for emergency medical help immediately. Keep the victim lying down, warm, and comfortable until help arrives. Avoid moving the victim in case of injury to neck or back. Position an unconscious victim on a side to let fluids drain. Check the victim’s breathing and heartbeat. If properly trained, apply mouth-to-mouth resuscitation and/or CPR if necessary.
