SilverStar ™ Silver Boom 130 www.silverstarmobility.com www.pridemobility.
SAFETY GUIDELINES WARNING! An authorized Pride Provider or qualified technician must perform the initial setup of this lift and must perform all of the instructions in this manual. The symbols below are used throughout this owner's manual and on the product to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Indicates a potentially hazardous condition/situation.
C O N T E N T S I. INTRODUCTION ......................................................................................................................... 4 II. SAFETY ......................................................................................................................................... 6 III. INSTALLATION .......................................................................................................................... 8 IV. OPERATION ...........................................
I. INTRODUCTION Welcome to Silver Star, a division of Pride Mobility Products Corporation (Pride). Congratulations on the purchase of your SilverBoom 130 lift. The SilverBoom 130 design combines the most advanced state-of-the-art components with modern, attractive styling. We are certain that the design features and trouble-free operation will add convenience to your daily living and ensure complete satisfaction. At Pride, your safety is important to us.
I. INTRODUCTION PRIDE OWNERS CLUB As an owner of a Pride product, you are encouraged to enroll in the Pride Owners Club. Complete and return your enclosed product registration card or visit Pride’s web site at www.pridemobility.com. As a registered member, each time you visit our site, you have access to the most interactive, educational venue available today for people with mobility needs, their families, and friends.
II. SAFETY PRODUCT SAFETY SYMBOLS The symbols below are used on the mobility product to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. Read and follow the information in the owner’s manual. Do not lift the mobility product while being seated in it. Do not lift people. Maximum lifting capacity. Pinch/Crush points created during assembly and/or operation. Do not lift pets.
II. SAFETY LIFTING CAPABILITIES The maximum weight the SilverBoom 130 was designed to lift is 130 lbs. Under no circumstances should the SilverBoom 130 be made to lift more than 130 lbs. Subjecting the SilverBoom 130 to the strain of hoisting more than it is designed to lift may cause it to fail, damaging your mobility product, injuring the person operating the lift, or both. WARNING! Adding accessories, oversize batteries, or a different seat will increase the weight of your mobility product.
III. INSTALLATION The SilverBoom 130 can be installed in either side of your vehicle. The illustrations demonstrate installation on the right side. BASE EXTENSIONS L-BASE NOTE: Most roads have a crown to help with water runoff. However, if the crown is severe enough, it may cause difficulty getting your mobility product into the vehicle. In this case it may be better to install the lift on the left side. DETERMINE L-BASE LOCATION 1. Assemble the L-Base. See figure 1.
INSTALLATION ! ASSEMBLING THE LIFT 1. Insert the upper post into the L-base. See figure 4. 2. Assemble the split ring collar. See figure 5. 3. Slide the split ring collar over the upper post and tighten both screws (a good starting point is approximately 12 in. down from the top of the upper post). See figure 4. To ensure safe operation, the split ring collar must be secured no closer than 5 in. from the top of the upper post. MINIMUM OF 5” ! III.
III. INSTALLATION BOOM ARM ADJUSTMENT Before adjusting the boom arm, lower the lifting hook about 12 in. This will provide enough slack in the strap to enable the adjustable portion of the boom arm (top tube) to be pulled out of the bottom tube to its farthest adjustment hole. See figure 8. To adjust the boom arm: 1. Remove the bow tie cotter pin from the adjustment pin and remove the adjustment pin. 2. Slide the top tube in or out to the desired adjustment hole. 3.
III. INSTALLATION 2. If all is clear under the L-base, mark the position of the five (5) mounting holes and drill them using a 3/8-in. drill bit. Drill all mounting holes from inside the vehicle. See figure 9. 3. Reinstall the L-base and align the mounting holes of the L-base with the holes you just drilled. 4. Position the T-bar on the end of the base support that runs parallel with the rear of the vehicle, and install a mounting bolt and washer through it and the L-base. See figure 9.
III. INSTALLATION 7. Place the L-base cap over the L-base and secure it with the supplied screws. See figure 10. 8. Reinstall the upper post. 9. Reinstall the motor housing and make adjustments as necessary. The lift is now fully assembled. See figure 11. PHILLIPS HEAD SCREW 10 MM L-BASE CAP MOTOR HOUSING UPPER POST L-BASE CAP L-BASE T-BAR Figure 10. L-Base Cap Figure 11. Fully Assembled Lift ELECTRICAL WIRING INSTALLATION 1.
III. INSTALLATION 4. Connect the short black (ground) wire to a clean, bare metal area of the vehicle using the 12 mm (1/2 in.) sheet metal screw provided. Mount to an area close to the base of the lift. This allows adequate slack in the wire to make the harness connections. " Drill a 1/16-in. pilot hole where the ground wire will be attached to the vehicle. " Insert the screw through the ring at the end of the black (ground) wire and install the screw into the pilot hole.
I V. OPERATION LIFTING THE MOBILITY PRODUCT WARNING! Before operating the SilverBoom 130 for the first time, be absolutely sure you have the proper docking device for your mobility product. PRESS TO OPERATE LIFT IN PRESS TO OPERATE LIFT A DOWNWARD DIRECTION IN AN UPWARD DIRECTION DOWN UP 1. Position your mobility product (if lifting a scooter, ensure the key is removed and the tiller is fully lowered; if lifting a power chair, ensure the power is off) on the ground behind the installed lift.
I V. OPERATION the hook from the docking device. " Reposition the mobility product. " Attempt the lift again. WARNING! The maximum weight the SilverBoom 130 was designed to lift is 130 lbs. Subjecting the SilverBoom 130 to the strain of hoisting more than it is designed to may cause it to fail, damaging your mobility product, injuring the person operating the lift, or both. 6.
V. TROUBLESHOOTING LIFT WILL NOT OPERATE " Check the circuit breaker reset button. Reset if necessary. See figure 18. " Ensure all harness connections are secure. " Ensure the power wire leading to the positive battery terminal is tight and not corroded. " Check the fuse located on the red power wire near the battery. If blown, replace with a new 25amp fuse. See figure 19. WARNING! Do not use a higher rated fuse than 25-amp. Doing so may damage the lift’s electrical system.
VI.
*INFMANU3530*