YX-2007 Show-Pro (RGB) Laser USER MANUAL www.yagang.com Version 1.2 2006.4.
1) Open the box for checking • • • • • • • • • • • • • • • • • • • • Pa ge 1 2) Installation • • • • • • • • • • • • • • • • • • • • • • • • • • • • Pa ge 1 3) Attention • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Pa ge 2 4) Warning • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Pa ge 2 5) Structure of the fixture • • • • • • • • • • • • • • • • • • • • • • Pag e 3 6) Control board instruction • • • • • • • • • • • • • • • • • • • • Pa ge 4 7)Control PCB Replacement• • • • • • • •
1. Open the box for checking In order to use this product safety and reasonable for the users, please read over this manual carefully before use and the operation must strictly according to this manual to avoid any damage to the product and personal safety. Once after received this products please take and put carefully.
3. Attention 1. Must operate according to the user manual. Don't separate the light personally. Call the technician when the machine breaks down. 2. Please do not see the laser beam directly to avoid any damage. 3. Before connect or disconnect the power, please adjust the luminance of the laser diode to the least to avoid any damage to the laser diode. 4. This unit should be keep dry, do not use in the rain or dank and dusty environment. It can be use in the outdoor with the water-proof cover protector. 5.
. Structure of the fixture No . Description. Qty No . Description.
. Control board instruction 7 6 ILDADB-25F Connector-IN ADDRESS ILDADB-25F Connector-OUT IN ON Remote Lock Security key switch DMX OUT ON OFF OFF POWER INPUT 1 2 3 1 2 3 4 5 4 5 Remote Lock In the event of removal, laser will not emit any beam.(E.U. IEC regulation) Security key switch Laser diode ON/OFF POWER ON/OFF Power switch POWER INPUT Input power, with inner fuse.
. Control PCB Replacement Steps: Disassemble defective PCB and then assemble new PCB.Make some marks of cable connection of refer to electrical diagram so that the connection of cables shonld be exactly same as original one.
. Scan motor Replacement (1) Steps: 1. Unscrew UK M6 screw and plug out male signal connector. 2. Disassemble all M4 10 screw for X,Y scanner socket so that scan motors can be took out,put in or rotate to adjust the scan angle. 3. After adjust ,fix M4 10 screws,plug in male signal connector and then screw UK M6 screw.
. Adjustable mirror socket (1) Steps 1. Loose setscrew of X,Y and then adjust mirror socket to suitable position by X,Y adjustable screws. 2. Adjust Z adjustable screw at same time. 3. Fix X,Y setscrew. NOTE:Made sure all beams through adjustable mirror socket be one point when you adjust X,Y,Z line with adjustable screw.
. Laser diode replacement Methods: Disassemble whole laser system (include power supply1,power supply 2,laser diode) and then replace new one at original position. Note:keep laser diode,power supply and cables be ompletly and don`t try to damage,destroy or cut them so that it can be repaired (crefer fig 1-7).
. Electrical diagram of laser 2 5 3 7 4 1 9 6 8 Fig 11-1 TOP 2 5 3 4 7 9 6 1 8 Fig11-2 1 power supply 1 of blue laser diode 6 power supply 2 of green laser diode 2 power supply 2 of blue laser diode 7 power supply 1 of red laser diode 3 blue laser diode 8 Green laser diode 4 red laser diode 9 power supply 1 of green laser diode 5 power supply 2 of red laser diode 9
. DMX512 Operate The product has 16 operate channels(international standard DMX512 signal),The details as follow 1 Brightness 2 Colour 3 Pattern Group 4 5 6 7 8 9 10 11 pattern 13 14 15 Horizontal roll Vertical roll Z roll Horizontal move Vertical move Horizontal stretch Vertical stretch Horizontal & Vertical stretch Slow-draw speed Point-Draw Scan speed 16 Pattern size 12 DMX512 Value 0~255 0~25 26~51 52~77 78~103 104~129 130~155 156~181 182~207 208~233 234~255 0~31 32~63 64~95 96~127 128~1
. Specification Ø Ø Ø Ø Ø Ø Ø Voltage: AC 220V~240V, 50/60Hz Total power: 120W Signal input power: -5~+5V X/Y axes beam scanning optical angle: 0~ Input signal bandwidth: 0~1000Hz Condition temperature: -10 ~+35 Laser Class 3B Laser light power: Red Green Laser Class 3B Blue Laser Class 3B Ø With Dimmer function Ø Net weight: 27 kg Ø Dimension: 62 x 30 x 19.5 cm 30 635nm 532nm 473nm >150mW >60mW >60mW 14.
Power supply 12 X Signal out Y Signal out -15V IN 0V IN +15V IN scan PCB scan PCB Pin 25 female PC plug Pin 25 male PC plug X scan motor TTL plug Y scan motor power supply of red laser diode red laser diode on/off switch Remote control connector TTL plug TTL plug Blue aser diode trasnsformer Power supply Power switch 15.
16. Trouble shooting SIUATION No power REASON Damaged fuse FAULTY PART PART NO.
Appendix ILDA DB 25F PINOUTS DB 25 definens 1 X -5 to 5V 2 Y -5 to 5V 3 Intensity/Blanking 0V to 4 Interlock A Connected to pin 17 inside the Qm2000 5 Red 0V to 2.5V 6 Green 0V to 2.5V 7 Blue 0V to 2.5V 8 Deep blue 0V to 2.5V 9 Yellow 0V to 2.5V 10 Cyan 0V to 2.5V 11 Z Depth Z(not intensity), -5 to 12 Not connected 13 Shutter 14 X 5V to 5V 15 Y 5V to 5V 16 Intensity/Blanking 2.5V to 0V 17 Interlock B 18 Red 2.5V to 0V 19 Green 2.
