CV_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:53 Uhr 3BC Seite 1 UNIVERSAL REMOTE CONTROL KH2150 UNIVERSAL REMOTE CONTROL Operating instructions KOMPERNASS GMBH · BURGSTRASSE 21 · D-44867 BOCHUM www.kompernass.com ID-Nr.
CV_KH2150_JOE23594_LB3bcI.qxd 05.08.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 CONTENT 16:52 Uhr PAGE Safety 3 Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Appliance Overview 4 First use 5 Unpacking the device / checking the package contents . . . . . . . . . . . . . . . . .5 Inserting the batteries . . . . . . . . . . . . . . . . . . . . . . . . .5 Operating elements 6 LCD display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Buttons . . . . . . . . . . . . . . . . . . . . .
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 MACRO-SETUP – Macro functions 16:52 Uhr 27 MACRO SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 MACRO CLEAR . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Maintenance and Cleaning 29 Battery maintenance . . . . . . . . . . . . . . . . . . . . . . . .29 Cleaning the remote control . . . . . . . . . . . . . . . . . .
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr UNIVERSAL REMOTE CONTROL KH2150 Safety Proper use Children may only operate the remote control under adult supervision. The universal remote control can replace a maximum of ten remote controls. It can only be used for entertainment electronics with infrared receivers. The functions of the universal remote correspond to those of the original remote controls. The universal remote control is intended for private use. It is not suitable for commercial use.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Damage to the device • If the device is defective, do not attempt to repair it yourself. In case of damage, contact the manufacturer or his service hotline (see Warranty section). • If liquid escapes from the device or if the device has been otherwise damaged, it must be inspected by the manufacturer or his service hotline. Contact the manufacturer or his service hotline (see Warranty section).
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr First use Unpacking the device / checking the package contents Attention! Keep the plastic packaging well away from small children. There is a risk of suffocation. • Unpack the device and accessories. • Check the package contents - Universal remote control - Operating instructions - Manufacturer list with device code list • Remove the protective foil from the LCD display (2).
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Note: If the LCD display (2) remains dark, check the polarity of the batteries or insert new batteries. The LCD display (2) is explained in the section LCD display. Operating elements LCD display The LCD display (2) is divided into fields. Text field (21) The text field has two lines. The first line indicates the current device, such as DVD, TV or VCR. The second line shows the day of week information or device code.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr AM/PM symbol (26) If the time is set to 12-hour format, a PM symbol is displayed in the afternoon between 12:00 and 24:00. (See section SYSTEM-SETUP – System settings). Number field (27) The display field for time and date information as well as the device code. Standard display The standard display on the LCD display (2) consists of the information for the current device "TV", the day of the week "SUN“ and the time "12:00“.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr CD player (Compact Disk) Amplifier Auxiliary 2 S button (5) Load SETUP menu or activate SHIFT function. Arrow buttons (6) Move up, right, left and down in menus. OK button (7) You can confirm a menu selection with the OK button. EXIT button (8) # Leave menu. Speaker button (9) Switch sound on/off. VOL button (10) Set volume. MACRO button (11) Pressing the MACRO button (11) followed by a number button (13) 1, 2 or 3 activates the saved commands.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Video text buttons (12) Switch on video text. Stop automatic paging forward for multi-page video texts. Display information on the selected device. Show video text and television programme at the same time. Switch off video text. Number buttons (13) Enter programme and device code numbers. Button for one-/two-digit programme numbers (14) Button for one-/two-digit programme numbers.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr CH button (17) Change the television channel. MENU button (18) Open the menu. EPG button (19) TV/SAT DVD : VCR : Depending on the selected device, the EPG button activates the following functions: Access the electronic television programme guide. Access the title menu. Access ShowView. Note: Consult the operating instructions of your VCR to learn whether the "ShowView" function is supported.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr SYSTEM-SETUP overview VOL/MUTE SETUP All devices use their own volume control, if available. If a video device, such as a VCR or DVD player, does not have its own volume control, the volume control of the television device is automatically used ("punch-through function"). The function VOL/MUTE SETUP allows you to set the volume control to operate through a specific device, such as the television. 1.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr VOL/MUTE SET Set the volume control for each individual device. 1. Hold the S button (5) pressed until CODE-SETUP appears in the LCD display (2). 2. Press the down arrow button (6). SYSTEM-SETUP appears in the LCD display (2). 3. Press the right arrow button (6). VOL/MUTE SETUP appears in the LCD display. 4. Press the right arrow button (6). ALL VOL.SET appears in the LCD display (2). 5.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr 4. Press the down arrow button (6) repeatedly until TIMESETUP appears in the LCD display (2). 5. Press the right arrow button (6). TIME? 24HR 12:00 appears in the LCD display (2). The message 24HR blinks. Note: Press the up or down arrow button for (6) 12-hour display. All other settings are explained using 24-hour display as example. 6. Press the right arrow button (6). TIME? 24HR 12:00 appears in the LCD display(2). The hours value blinks. 7.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Note: If no button is pressed for approx. 30 seconds, the message TIMEOUT appears in the LCD display (2). Then the standard display is shown automatically. BACKLIGHT SETUP Set the backlight time for the LCD display (2). The backlight time can be changed in five second steps. 1. Hold the S button (5) pressed until CODE-SETUP appears in the LCD display (2). 2. Press the down arrow button (6). SYSTEM-SETUP appears in the LCD display (2). 3.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr 2. Press the down arrow button (6). SYSTEM-SETUP appears in the LCD display (2). 3. Press the right arrow button (6). VOL/MUTE SETUP appears in the LCD display (2). 4. Press the down arrow button (6) repeatedly until SYSTEMRESET appears in the LCD display (2). 5. Press the right arrow button (6). CONFIRM RESET appears in the LCD display (2). 6. Press the right arrow button (6). PLEASE WAIT... appears in the LCD display (2).
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr CODE-SETUP overview 7. Confirm the selection with the OK button (7). First PLEASE WAIT... then the first entry of the manufacturer list, such as ADMIRAL 0000, appears in the LCD display (2). 8. Press the up or down arrow button (6). The next manufacturer with device code appears in the LCD display (2). 9. Press various buttons on the remote control to test the functions. If your device responds, you have selected the correct device code.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr ENTER CODES With the ENTER CODES function, you locate the device code in the enclosed manual “Manufacturer List with Device Code List“. Note: To conclude your input, press the EXIT button (8). 1. Switch on the device for which you would like to program the remote control. 2. Hold the S button (5) pressed until CODE-SETUP appears in the LCD display (2). 3. Press the right arrow button (6). LIST CODES appears in the LCD display (2). 4.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Note: For a television, press the device button TV (4), then continue with step 8. 7. Press the up or down arrow button (6). The next device appears in the LCD display (2). 8. Confirm the selection with the OK button (7). SEARCH KEY? appears in the LCD display (2). Note: The remote control switches the device code every second and sends an infrared signal. To set the time to three seconds, press the CH button (17) twice during the next step. 9.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Note: For a television, press the device button TV (4), then continue with step 8. 7. Press the up or down arrow button (6). The next device appears in the LCD display (2). 8. Confirm the selection with the OK button (7). SEARCH KEY? appears on the LCD display (2). Note: The remote control searches the device list in the forward direction. To change the search direction, press "Minus" on the CH button (17).
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Note: All entries in the device list can be found in the overview graphic. 8. Confirm the selection with the OK button (7). BRAND CODES? appears in the LCD display (2). 9. Search for the manufacturer code in the "Manufacturer codes" table in the appendix to these operating instructions. 10. Enter the manufacturer code with the number buttons (13). SEARCH KEY? appears in the LCD display (2). 11.Press the CH button (17) until the device responds. SEARCH...
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr TIMER SETUP – Timer functions Program the automatic switch-off function SLEEPTIMER and the automatic switch-on function "TIMER". See the graphic "TIMER-SETUP overview“. TV SLEEP SETUP The SLEEPTIMER function automatically switches off the television after the configured time has elapsed. The SLEEPTIMER function can be set between 1 and 90 minutes. TV SLEEP SET Programming the SLEEPTIMER function. 1. Switch on the television. 2.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Note: Select a value between 1 and 90 minutes. 7. Press the up or down arrow button (6) to set the minutes. 8. Press the right arrow button (6). SUCCESS and the Zzz symbol (25) appear in the LCD display (2). 9. Point the remote control at the television. After the configured number of minutes elapse, the remote control will switch off the television. 10. Press the EXIT button (8) repeatedly until the standard display appears in the LCD display (2).
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr TIMER X SET Programming TIMER X. The "X“ is a placeholder and stands for 1, 2, 3 or 4. All settings are described using TIMER 1 as an example. 1. Hold the S button (5) pressed until CODE-SETUP appears in the LCD display (2). 2. Press the down arrow button (6) repeatedly until TIMERSETUP appears in the LCD display (2). 3. Press the right arrow button (6). TV SLEEP SETUP appears in the LCD display (2). 4.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr 5. Press the down arrow button (6) repeatedly until the desired TIMER appears in the LCD display (2). 6. Press the right arrow button (6). CONFIRM CLEAR appears in the LCD display (2). 7. Press the right arrow button (6). First SUCCESS then CODE SETUP appears in the LCD display (2). 8. Press the EXIT button (8) repeatedly until the standard display appears in the LCD display (2). Note: If no button is pressed for approx.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr LEARN SETUP overview MODE LEARN Note: Execute "ALL LEARN CLEAR“ before executing "MODE LEARN“ for the first time. See section "ALL LEARN CLEAR“. Learning the button signals of an original remote control. 1. Hold the S button (5) pressed until CODE-SETUP appears in the LCD display (2). 2. Press the down arrow button (6) repeatedly until LEARNSETUP appears in the LCD display (2). 3. Press the right arrow button (6).
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Note: If "LEARN ERROR“ appears in the LCD display (2), repeat the learning function process starting from step 5. 7. Hold the button on the original remote control pressed until first SUCCESS then LEARN MORE? appears in the LCD display (2). Note: To end the learning function, press the EXIT button (8). 8. Press the right arrow button (6) to learn more buttons. LEARN MORE? appears in the LCD display (2). Repeat steps 5 to 7 to learn more buttons.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr MACRO-SETUP – Macro functions With the macro function, you can save a sequence of button presses. The saved macro can be loaded with the MACRO button (11) and the number buttons (13) 1, 2 or 3. The saved button sequence is executed automatically. An example of a button sequence would be: • Switch on television. • Change television channel. • Switch on VCR. • Record programme. The macro function an store three different macros.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Note: After the tenth button press, the macro is automatically saved. To save the macro at an earlier point, press the button MACRO (11). 7. Press the desired button sequence. With each button press, the counter goes up by one: MACRO1 KEY? 03, MACRO 1 KEY? 04 etc. After the tenth button press, the macro is saved and SUCCESS appears in the LCD display (2).
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Maintenance and Cleaning Battery maintenance Memory function The device codes and learned buttons are retained during a battery change. The following are immediately deleted: Time information and the lighting time for the backlight of the LCD display (2). These settings must be entered again after a battery change. Change the batteries... - once per year. - when the LCD display (2) is difficult to read.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Troubleshooting Problem Possible cause Universal Device (e.g. TV) is remote control defective. does not respond Batteries are inserted incorrectly. Solution Check functioning of the device (e.g. TV) with the original remote control. Insert the batteries into the battery compartment with the correct polarity. Batteries are empty. Device codes Batteries are are not saved. empty. Insert new batteries. Insert new batteries. LCD display (2) is dim.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Technical data Manufacturer: Device type: Model: Controllable devices Dimensions L x W x H: Weight : Infrared transmitter frequency: Range: Angle: Laser: Power supply Battery: Kompernaß GmbH 10-in-1 universal remote control KH 2150 10 200 x 48 x 22 mm 92 g >100 kHz 8m 50° Laser class 1 2 x 1.5 V, type AAA/LR03 (micro) Manufacturer codes One manufacturer code applies to multiple manufacturers. For example, enter the code 3 for a Sharp device.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Conformity The first party placing the product KH 2150 and all its accessories on the market and bearing responsibility in accordance with the German Equipment and Product Safety Act (GPSG) as well as for compliance with the directives on use of the CE mark is: KOMPERNASS GMBH BURGSTRASSE 21 44867 BOCHUM, GERMANY The conformity declaration can be requested from the first party placing the product on the market.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.2008 16:52 Uhr Seite 34 Warranty and Service You receive a 3-year warranty for this device as of the purchase date. Should you have grounds for complaint in spite of our high quality standards, please contact our Service Hotline. In the event that processing of your complaint is not possible by telephone here you will receive • a processing number (RMA number) as well as • an address, to which you can send your product for warranty processing.
In order to guarantee a cost free repair procedure please get in touch with the service hotline. Make sure you have your sales slip handy. UNIVERSAL REMOTE CONTROL KH 2150 www.mysilvercrest.de Irish Connection Tel: 00353 (0) 87 99 62 077 Fax: 00353 18398056 e-mail: support.ie@kompernass.com DES Ltd Tel.: 0870/787-6177 Fax: 0870/787-6168 e-mail: support.uk@kompernass.com Warranty 05.08.
IB_KH2150_JOE23594_LB3bcI.qxd 05.08.
