PERSONAL CARE Hair Trimmer SHBS 1000 A1 Hair Trimmer Operation and Safety Notes 6
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the device.
1 2 3 4 5 A 6 6 6 7
B C D E F G
Table of Contents Introduction Proper use................................................................................. Page Included items.......................................................................... Page Description of parts.................................................................. Page Technical data.......................................................................... Page 7 8 8 9 Safety......................................................................................
The following icons / symbols are used in this instruction manual: Read instruction manual! Damaged appliances, power cables and power plugs mean potentially fatal risks from electric shock. Regularly check the condition of the appliance, the power cables and the power plugs.
Introduction Hair Trimmer Q Introduction Dear Customer, We are pleased you chose to purchase this product and hope you enjoy using your new hair and beard clippers. These hair and beard clippers and their easily fitted cutting length comb attachments 6 can be used to cut different hair lengths and shape perfect hair contours. The clippers also have a sliding switch 2 for fine adjustment of the cutting length.
Introduction Q Included items 1 Hair and beard clippers 1 Charging station 1 Plug-in adapter 6 Cutting length comb attachments 1 Thinning attachment 1 Cleaning brush 1 Scissors 1 Comb 1 Cutter oil 1 Travel bag 1 Hairdressing cape 1 Instructions for use Q Description of parts 1 Blade set with titanium-coated blade block and ceramic cutting blade 2 Sliding switch for fine adjustment of cutting length 0.5 mm / 1.2 mm / 1.9 mm / 2.
Introduction / Safety Q Technical data Plug-in mains adapter: Input: Output: Protection class: Ambient conditions: Hair and beard clippers: Model: Article No.: Rechargeable batteries: Input: Permissible ambient temperature range: Q 100 - 240 V ~, 50 / 60 Hz 4.5 V , 1,000 mA For indoor use only SHBS 1000 A1 9133711 2 x NiMH, HR6 (AA) 1,000 mAh 4.5 V , 1,000 mA +10 °C to +40 °C Safety Please read carefully through the operating instructions before using the device for the first time.
Safety General safety advice J T his device is not intended to be used by persons (including children) with restricted physical, sensory or mental abilities or with insufficient experience and / or knowledge, unless they are supervised by a person who is responsible for their safety or they have received instruction on how to use the device from such a responsible person. Children should be supervised in order to ensure that they do not play with the device.
Safety The device will operate at its best if you observe the following: J J J T o ensure optimum performance, operate the device only in accordance with the information on the rating plate. Do not expose the hair clippers to temperatures below +10 °C or above +40 °C. Thoroughly clean the device after each use. To avoid the danger of loss of life from electric shock: J Disconnect the mains adapter after use or before cleaning. c CAUTION! DANGER OF ELECTRIC SHOCK! Do not use while in the bath.
Safety c CAUTION! DANGER OF ELECTRIC SHOCK! If the device falls into the water, the first thing you must do is pull the mains adapter out of the mains socket before you put your hands into the water. c CAUTION! DANGER OF ELECTRIC SHOCK! Never touch the mains adapter with wet hands particularly when you insert or pull out the adapter from the mains socket. J Handle the mains adapter only by its body when you insert it into the mains socket.
Safety / Before first use J P ull the mains adapter out of the mains socket - if a fault occurs, - before you clean the device, - if you intend leave the device unused for a long period, - after every use. When doing this, pull directly on the mains adapter and not on the lead. J Stop using the device immediately if the lead, mains adapter, housing or any other part is found to be damaged. J Use only the supplied original mains adapter for mains operation.
Before first use The device is fitted with 2 NiMH rechargeable batteries and an overcharge protection system so that the batteries can be topped up without being overcharged. j j j j j j onnect the cable of the plug-in mains adapter to the charging C station 5 of the hair and beard clippers. Avoid injury and damage to the device! Make sure that the device is switched off before you charge the rechargeable batteries.
Before first use / Use j j j j j I nsert the connector plug of the plug-in mains adapter into the socket on the underside of the hair and beard clippers. To avoid injury and damage to the device, always switch off the device before you connect it to the mains supply. Insert the plug-in mains adapter (wide voltage range 100 - 240 V) into a mains outlet socket that meets the requirements of the device. After 1 - 2 seconds you can switch on the device by pressing the ON / OFF switch 3 .
Use Q Cutting hair Tip: Start with a cutting length comb attachment with a longer cutting length than is finally required, then proceed in stages until you achieve the desired length. Cutting length comb attachments 6 : j Select the cutting length comb attachment 6 (4 - 6 mm / 7 - 9 mm / 10 - 12 mm / 16 - 18 mm / 22 - 24 mm / 28 - 30 mm) to suit the desired cutting length. j Push the selected cutting length comb attachment 6 from the rear on to the blade set 1 .
Use Cutting length comb Cutting lengths* attachment 6 (mm) with cutting length fine adjustment (mm) 0.5 1.2 1.9 2.5 22 - 24 22.0 22.7 23.4 24.0 28 - 30 28.0 28.7 29.4 30.0 * Please note that the actual cutting lengths may deviate from the cutting lengths given here, depending on the cutting angle. j j j j Q lways cut off small amounts at a time. A Guide the hair and beard clippers slowly through the hair.
Use / Cleaning and care Q Thinning hair This attachment allows you to reduce the volume of hair by only picking up and cutting part of the hair. j P ush the thinning attachment 7 on to the blade set 1 from the front to thin out the hair. This attachment reduces the volume of the hair. Q Cutting to shape the hairline, neck and sideboards j j j T urn the device over so that the back is facing upwards.
Cleaning and care j j ever touch the mains adapter with wet hands when you insert N or pull out the adapter from the mains socket. Always keep the mains adapter and connection lead dry. Warning! Do not immerse the hair and beard clippers in water or other liquids for cleaning as the device is not waterproof. Failure to observe this advice could damage the electrically conducting parts (rechargeable batteries). Q Cleaning the housing j Clean the housing using a slightly moist cloth.
Cleaning and care / Disposal j j fter cleaning, place the locating lug of the blade set 1 back A into the locating hole of the cutter head mount (see Fig. C). Re-engage the blade set 1 by applying a little light pressure from the rear of the device (see Fig. D). Tip: To reduce friction apply one or two drops of cutter oil (accessory) from time to time between the blades and spread it out evenly. You may also use any acid-free oil (such as sewing machine oil). Wipe away any excess oil with a cloth.
Disposal / Warranty and service When you decide to discard the device, please do not place it (even without batteries) into the household refuse bin. Contact your local council to find out about environmentally friendly and proper disposal of the device as electrical scrap. The packaging is composed of natural materials and can be recycled. Dispose of these materials properly in the interests of environmental protection.
Warranty and service / Conformity We are furthermore unable to assume liability for the consequences of improper use of the device.
IAN 61924 Lutter & Partner GmbH Schleissheimer Strasse 93 a D-85748 Garching bei München L&P Art.-Nr. 9133711 © by ORFGEN Marketing Last Information Update: 12 / 2010 Ident.-No.