EC03-P MANUAL PCI express card with USB 3.0 internal connector 10% performance boost over first gen USB 3.
EC03-P PCI express card with USB 3.0 internal connector Introduction SilverStone EC03-P is an expansion card that connects to the motherboards via a single lane PCI-E gen 2.0 slot. Its single USB 3.0 internal connector offers output for dual front port USB 3.0 super speed interface which enables data transfer with maximum compatibility and stability. For those looking to use cases or drive bays that supports the new USB 3.
EC03-P PCI express card with USB 3.0 internal connector Installation Steps Insert the included 3.5” front I/O bay into the chassis Secure the I/O bay with screws on the left side 3 Secure the I/O bay with screws on the right side 4 Connect USB 3.0 connector from the I/O bay to EC03-P’s corresponding pin header 1 2 USB 3.
EC03-P PCI express card with USB 3.0 internal connector INSTALLATION 1 Install EC03-P onto PCIe slot of Motherboard. Установите плату EC03-P в гнездо PCIe материнской платы. Installieren Sie die EC03-P im PCIe-Steckplatz des Motherboards. 將EC03-P安裝於主機板上的PCI-E插槽。 Installez le EC03-P dans un emplacement PCIe de la carte mère. 将EC03-P 安装于主机板上的PCI-E插槽。 Instale el EC03-P en el zócalo PCIe de la placa base. EC03-P をマザーボードのPCIeスロットにインスト ールします。 Inserisci EC03-P nello slot PCIe della scheda madre.
EC03-P PCI express card with USB 3.0 internal connector INSTALLATION 2 Plug Molex 4P power connecter. Подсоедините 4-контактный разъем питания Molex. Schließen Sie den 4-poligen Molex-Netzstecker an. 將4pin電源線接上EC03-P。) Branchez le cordon d'alimentation Molex 4P. 将4pin电源线接上EC03-P。 Conecte el Mólex 4P en el conector depotencia. Plug Molex 4P電源コネクタを接続します。 Connett il molex 4P alla presa d’alimentazione. Molex 4P 파워 커넥터를 연결합니다.
EC03-P PCI express card with USB 3.0 internal connector INSTALLATION 3 Plug internal 20P dual port USB 3.0 connector. Подсоедините внутренний 20-контактный разъем для двух портов USB 3.0. Schließen Sie den 20-poligen internen Dual-PortUSB 3.0-Stecker an. 連接EC03-P與20pin USB 3.0訊號線。 Branchez le connecteur USB 3.0 à double port interne 20P. 连接EC03-P与20pin USB 3.0讯号线。 Conecte el puerto dual 20P al conector USB 3.0. 内蔵20PデュアルポートUSB 3.0コネクタを接 続します。 Connetti la doppia porta interna 20P USB 3.0.
EC03-P PCI express card with USB 3.0 internal connector INSTALLATION 4 Install Renesas USB 3.0 host controller driver. Установите драйвер хост-контроллера Renesas USB 3.0. Installieren Sie den USB 3.0-Host-ControllerTreiber von Renesas. 安裝Renesas USB 3.0 host controller驅動程式。 Installez le pilote du contrôleur hôte Renesas USB 3.0. 安装Renesas USB 3.0 host controller驱动程序。 Instale el controlador Renesas USB 3.0. USB 3.0ホストコントローラドライバをインストール します。 Installa il driver Renesas USB 3.0 host controller.
EC03-P PCI express card with USB 3.0 internal connector INSTALLATION 5 After above installation, you will find the Renesas USB 3.0 host controller in the device manager. (refer to PIC1) После установки указанного выше драйвера хост-контроллер Renesas USB 3.0 отобразится в диспетчере устройств. (см. рисунок 1) Nach der obigen Installation finden Sie den USB 3.0-Host-Controller von Renesas im Geräte-Manager. (vgl.Abb.1) 安裝完成後,在硬體管理員列表中可看見 Renesas USB 3.
EC03-P PCI express card with USB 3.
EC03-P PCI express card with USB 3.0 internal connector INSTALLATION 6 Plug your USB 3.0 device and enjoy the 5Gbit/s USB 3.0 super speed transfer speed. Подключите устройство с интерфейсом USB 3.0 и передавайте данные на высокой скорости до 5 Гбит/с через разъем USB 3.0. Schließen Sie Ihr USB 3.0-Gerät an und genießen die USB 3.0-Super-SpeedÜbertragungsgeschwindigkeit von 5 Gbit/s. 連接USB 3.0裝置並開始享受高速傳輸速度。 Branchez vos appareils USB 3.0 et profitez de la super vitesse de transfert de 5Gbit/s.
November, 2011