SST-SG01-F
SST-SG01-F SST-SG01B-F Model No. Standard SST-SG01S-F Material Aluminum front panel, SECC body Color Black / Silver Motherboard Micro ATX Drive Bay Cooling System External 5.25" x 2 Internal 3.5" x 2 Rear 1 x 80mm exhaust fan 2050rpm Optional cross-flow fan Sides 1 x 80mm intake fan 2050rpm Option 80mm or 70mm in thick of 25mm, 15mm or 10mm Top 1 x 80mm fan slot Expansion Slot Front I/O Port USB2.
Top cover 8025 FAN 5.25 bay x 2 8025 FAN (optional) Expansion Slot x 4 8025 FAN MIC AUDIO x 1 USB2.0 x 2 IEEE 1394 3.5 HDD x 2 HDD Tray x 2 Reset Button Power Button Special Features: Steel structure for silent builds Cleanly styled aluminum front panel Enhanced cooling layout for high performance Dual 5.25” and 3.5” drive bays Micro ATX motherboard & ATX PSU compatible Extended-length expansion cards support Included package MOTHERBOARD STAND SECURE MOTHERBOARD WIRE MOUNT TIE CABLES SECURE 5.
繁 體 中 文 簡 体 中 文 请依图示以螺丝起子卸下机箱上盖螺丝, 再将上盖向后拉以取出机箱 繁 體 中 文 簡 体 中 文 请依图示卸下锁固扩充卡槽档片螺丝, 并将其自SG01-F机箱中取出
繁 體 中 文 簡 体 中 文 请依图示将风扇架上的螺丝卸下, 并将风扇架自SG01-F机箱中取出 繁 體 中 文 簡 体 中 文 请依主板需求锁固主板螺柱
繁 體 中 文 簡 体 中 文 请依图标将主板安装至SG01-F机箱 繁 體 中 文 簡 体 中 文 请以内附螺丝(螺丝A)锁固您的主板
繁 體 中 文 簡 体 中 文 请依图示自机箱上方安装您的电源供应器, 并已内附的螺丝(螺丝B)锁固 Remove the screws on 5.25” bay cover and then remove it outward from chassi Entfernen Sie die Schrauben an den Blenden der 5.25’’ Einschübe und entfernen Sie die Blenden Remove the screws on 5.25” bay cover and then remove it outward from chassi 繁 體 中 文 請依圖示卸下5.25吋裝置槽檔板螺絲, 並將其自SG01-F機箱中取出 Retirez les vis des caches de baie 5.25” et ensuite retirez-les du boîtier 5.
繁 體 中 文 簡 体 中 文 请依图示自SG01-F正面安装您的光盘装置, 并以内附螺丝(螺丝A)锁固
繁 體 中 文 簡 体 中 文 请依图标将硬盘托盘上的螺丝卸下, 并将其自SG01-F机箱中取出
1 2 繁 體 中 文 簡 体 中 文 请依图标将您的硬盘装入托盘,并以内附 螺丝(螺丝B)锁固后,将您的硬盘连同托盘 装回SG01-F机箱,并以步骤10卸下的螺丝 锁固。 请注意,将硬盘安装至拖盘时,方向必须 与硬盘线材插槽的方向一致 9
2 繁 體 中 文 簡 体 中 文 安装显卡或扩充卡 (如需安装超长扩充卡, 请参阅其安装指南) Reinstall the fan bracket into chassis and secure with screw. (optional 80mm fans can be installed onto the fan bracket.) Setzen Sie die Lüfterhaltung wieder in und schrauben Sie diese fest. (optional kann ein 80mm Lüfter installiert werden.) Установите обратно в корпус и закрепите кронштейн вентилятора. (В кронштейн вентилятора можно установить дополнительные 80-мм вентиляторы.
4 繁 體 中 文 簡 体 中 文 请将扩充卡槽档版装回机箱, 并以内附螺丝锁固 5 繁 體 中 文 簡 体 中 文 请确认所有必须的线材与线路都已连接后, 将上盖装回并以螺丝锁固 11
6 繁 體 中 文 簡 体 中 文 安装完成 IEEE 1394 CONNECTOR USB2.
1 13
1 1 1 1 1 1 1 1 14
15
1 2 16
Optional SG01-F equipment SST-FX121 Add a cross flow fan for additional cooling (Notice : You can only add one device fromNT06-E or FX121.
April,2008 G11206940