SD01 Manual Aluminum hard drive pad with SATA 6Gbps and SAS 6Gbps support
Stackable Drive series SD01B Aluminum hard drive pad with SATA 6Gbps and SAS 6Gbps support Single stackable 6Gbps SAS/SATA hard drive pad Special Features Unique stackable design for easy upgrades and expansion Support SATA and SAS interface hard drive Maximum 6Gbits data transfer speed via SATA or SAS dual-lane interface Plug and Play & Hot-swappable connection (system with AHCI mode) The power source synchronizes with computer Specifications Model No.
Stackable Drive series SD01B Aluminum hard drive pad with SATA 6Gbps and SAS 6Gbps support 1. (PIC. 1) Adhere the pair of included 95 x 4 x 4mm sized rubber padding to the bottom of SD01 where the indented strips are located. (refer to PIC. 1) Прикрепите пару входящих в комплект резиновых подкладок размером 95 x 4 x 4 мм к нижней части контейнера SD01 в местах расположения специальных выемок. (см. рис.
Stackable Drive series SD01B Aluminum hard drive pad with SATA 6Gbps and SAS 6Gbps support 2. (PIC. 2) Adhere the pair of included 145 x 4 x 1mm sized rubber padding to the topside of SD01’s hard drive rails. (refer to PIC. 2) Прикрепите пару входящих в комплект резиновых подкладок размером 145 x 4 x 1 мм к верхней части направляющих для жесткого диска контейнера SD01. (см. рис.
Stackable Drive series SD01B Aluminum hard drive pad with SATA 6Gbps and SAS 6Gbps support 3. (PIC. 3) Route the included “DC plug to peripheral 4pin connector” and “eSATA 7pin to SATA 7pin connector” to the included rubber pass through. (refer to PIC. 3) Пропустите через резиновый уплотнитель входящие в комплект кабель со штекером питания и 4-контактным периферийным разъемом и кабель с 7-контактным разъемом eSATA и 7-контактным разъемом SATA. (см. рис.
Stackable Drive series SD01B Aluminum hard drive pad with SATA 6Gbps and SAS 6Gbps support 4. (PIC. 4) Take the routed cables from the previous step and route again through the included expansion slot cover. There are full-size and low profile covers available so use the one required by your case. (refer to PIC. 4) Проложите кабели с предыдущего шага через входящую в комплект крышку слота расширения.
Stackable Drive series SD01B Aluminum hard drive pad with SATA 6Gbps and SAS 6Gbps support 5. (PIC. 5) Route cables one more time through the expansion slot in your case and secure the expansion slot cover with screws. (refer to PIC. 5) Führen Sie die Kabel ein weiteres Mal durch den Erweiterungssteckplatz in Ihr Gehäuse und befestigen die Abdeckung des Erweiterungssteckplatzes mit Schrauben. (vgl. Abb.
Stackable Drive series SD01B Aluminum hard drive pad with SATA 6Gbps and SAS 6Gbps support 6. PSU (PIC. 6) Connect peripheral 4pin connector to the corresponding connector from the power supply and make sure the connection is secure. (for steps 6 through 8, refer to PIC. 6) Подключите 4-контактный периферийный разъем к соответствующему разъему от блока питания и проверьте надежность соединения. (шаги 6–8 проиллюстрированы на рис.
Stackable Drive series SD01B Aluminum hard drive pad with SATA 6Gbps and SAS 6Gbps support 7. Connect the SATA 7pin connector to the corresponding SATA connector on the motherboard. If you need to activate hot-swap capability, please setup AHCI mode in the motherboard BIOS. For systems with Windows XP, you must install AHCI driver. (downloadable from Microsoft’s website)Connect eSATA 7pin connector and DC plug to corresponding connectors on the SD01.
Stackable Drive series SD01B Aluminum hard drive pad with SATA 6Gbps and SAS 6Gbps support 8. (PIC. 7) If you purchased more than one SD01 and wish to stack them on top of each other, please install the included hexagonal nut and stud on one SD01 first, then place another SD01 on top of the stud and secure them using the included M3 screws. (refer to PIC.
Stackable Drive series SD01B Aluminum hard drive pad with SATA 6Gbps and SAS 6Gbps support
Issue Date : April, 2011 NO.
