DOMINO 55M RS-232C CONTROL SPECIFICATIONS Document Revision 1.
SIM2 DOMINO 55M RS-232C CONTROL SPECIFICATIONS Table of Contents 1. INTRODUCTION 3 2. CONNECTION 3 3. COMMUNICATION PROTOCOL 4 HEADER PAYLOAD 4 4 4. COMMANDS 5 REMOTE CONTROL KEY CODES OPERATION CODES GET CODES 5 7 10 5. EXAMPLES 11 6. WARNINGS 12 Revision History: Revision Date Software Version Description of Change 1.0 21 January 2004 2.44.00 M or higher Initial version.
SIM2 DOMINO 55M RS-232C CONTROL SPECIFICATIONS 1. Introduction This document describes the communication and data formats used to control SIM2 DOMINO 55M via RS232C port. 2. Connection Switch off your Personal Computer and DOMINO 55M before connecting RS 232C cable. Use a standard serial cable with 9 pin female to the Personal Computer and 9 pin male to the DOMINO 55M: pin 2 connects to pin2, pin 3 to pin 3 and pin 5 to pin 5. SIM2 DOMINO 55M RS-232C Port is described as follows.
SIM2 DOMINO 55M RS-232C CONTROL SPECIFICATIONS 3. Communication Protocol The communication protocol is packet oriented. Packets consists of Header and Payload. There are two types of packets: Event and Operation. The packet header size is fixed (7 bytes), while the packet payload type and content varies based on the type of packet: Event payload size is 6 bytes, while Operation payload size is 25 bytes.
SIM2 DOMINO 55M RS-232C CONTROL SPECIFICATIONS 4. Commands Remote Control Key Codes The following commands send simulated Remote Control input to SIM2 DOMINO 55M.
SIM2 DOMINO 55M RS-232C CONTROL SPECIFICATIONS Direct access codes Goto Brightness BE EF 02 06 00 C7 E1 7E 01 00 00 00 00 Goto Contrast BE EF 02 06 00 16 E0 7F 01 00 00 00 00 Goto Color BE EF 02 06 00 19 F4 80 01 00 00 00 00 Goto Tint BE EF 02 06 00 C8 F5 81 01 00 00 00 00 (1) When the unit is in Stand-by state, this command switches on the unit and the last source memorised prior to switch off is automatically selected.
SIM2 DOMINO 55M RS-232C CONTROL SPECIFICATIONS Operation Codes The following codes provide direct access to SIM2 DOMINO 55M User Interface operations not accessible via a single Remote Control command.
SIM2 DOMINO 55M RS-232C CONTROL SPECIFICATIONS COLOR TEMPERATURE LOW USER FILM FILM 1 GAMMA VIDEO VIDEO 1 GRAPHICS INCREMENT FREQUENCY DECREMENT INCREMENT PHASE DECREMENT INCREMENT Y/C DELAY DECREMENT INCREMENT MAGNIFICATION DECREMENT INCREMENT PAN HORIZONTAL DECREMENT INCREMENT PAN VERTICAL DECREMENT SET ENGLISH SET ITALIANO SET FRANCAIS LANGUAGE SET DEUTSCH SET ESPANOL SET PORTUGUES OSD POSITION HORIZONTAL OSD POSITION VERTICAL INCREMENT DECREMENT INCREMENT DECREMENT BE 26 BE 27 BE 10 BE 0B BE 0D
SIM2 DOMINO 55M RS-232C CONTROL SPECIFICATIONS SET YCrCb AutoSync SET YCrCb 15kHz SET YCrCb 32kHz INPUT3 (COMP RGB 1) / SIGNAL TYPE SET RGB AutoSync SET RGB 15kHz SET RGB 32kHz SET YCrCb AutoSync SET YCrCb 15kHz SET YCrCb 32kHz INPUT 4 (COMP RGB 2) / SIGNAL TYPE SET RGB AutoSync SET RGB 15kHz SET RGB 32kHz RECALL SAVE CURRENT SETTINGS SAVE INITIAL SETTINGS MEMORY 1 RECALL SAVE CURRENT SETTINGS SAVE INITIAL SETTINGS MEMORY 2 RECALL SAVE CURRENT SETTINGS SAVE INITIAL SETTINGS MEMORY 3 BE 14 BE 08
SIM2 DOMINO 55M RS-232C CONTROL SPECIFICATIONS 8 9 Op Type 10 Op ID 11 12 01 00 13 14 Op Target 15 16 00 00 17 18 Value 19 20 00 00 21 22 23 24 25 26 27 28 29 30 31 32 00 00 00 00 00 00 00 00 00 00 00 00 Get Codes Get Commands may be used to get the current value of DOMINO 55M parameters.
SIM2 DOMINO 55M RS-232C CONTROL SPECIFICATIONS (1) Returned value is indeterminate when the unit is in No Signal state. Returned value may be different from the value displayed on the OSD, as in the latter, the values have been normalized to the 0-100 range. (2) Returned value is valid only when Video, S-Video, RGBS 15 kHz, YCrCb 15 kHz or YcrCb 32 kHz signals are displayed. Returned value is indeterminate when other signals are displayed and when the unit is in No Signal state.
SIM2 DOMINO 55M RS-232C CONTROL SPECIFICATIONS Command that simulate key 0 switches on the unit: the last source memorised prior to switch off is automatically selected. 2. Send the simulated "MENU RIGHT" Remote Control keycode. Send the packet: BEEF02060023E75A0100000000. The OnScreen Display appers on the screen. The DOMINO 55M returns the response code: 06 (Acknowledged with no error). 3. Send the "SET ASPECT ANAMORPHIC" Operation Code. Send the packet: BEEF0206009DF5840100000000.
