C3X LITE DLP™ VIDEO PROJECTOR RS-232C CONTROL SPECIFICATIONS Document Revision 1.
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS Table of Contents 1. INTRODUCTION 3 2. CONNECTION 3 3. COMMUNICATION PROTOCOL 4 HEADER PAYLOAD 4 4 4. COMMANDS 5 REMOTE CONTROL KEY CODES O PERATION CODES GET CODES 5 7 11 5. EXAMPLES 13 6. WARNINGS 14 Revision History: Revision Date Software Version Description of Change 1.0 02 Dicember 2005 2.48.59 CLT or higher Initial version.
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS 1. Introduction This document describes the communication and data formats used to control SIM2 C3X LITE projector via RS-232C port. 2. Connection Switch off the Personal Computer and the Projector before connecting RS 232C cable. Use a standard serial cable with 9 pin female to the Personal Computer and 9 pin male to the Projector: pin 2 connects to pin2, pin 3 to pin 3 and pin 5 to pin 5. SIM2 C3X LITE RS-232C Port is described as follows.
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS 3. Communication Protocol The communication protocol is packet oriented. Packets consists of Header and Payload. There are two types of packets: Event and Operation. The packet header size is fixed (7 bytes), while the packet payload type and content varies based on the type of packet: Event payload size is 6 bytes, while Operation payload size is 25 bytes.
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS 4. Commands Remote Control Key Codes The following commands send simulated Remote Control input to SIM2 C3X LITE projector.
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS Direct access codes Zoom BE EF 02 06 00 94 E6 5D 01 00 00 00 00 Focus BE EF 02 06 00 76 E7 5F 01 00 00 00 00 Brightness BE EF 02 06 00 C7 E1 7E 01 00 00 00 00 Contrast BE EF 02 06 00 16 E0 7F 01 00 00 00 00 Color BE EF 02 06 00 19 F4 80 01 00 00 00 00 Tint BE EF 02 06 00 C8 F5 81 01 00 00 00 00 (1) - When the unit is in Stand-by state, this command switches on the unit and the last source memorised prior to switch off is automatically selected.
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS Operation Codes The following codes provide direct access to SIM2 LITE User Interface operations not accessible via a single Remote Control command.
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS SET 04 SET 05 SET 06 SET 07 SET 08 SET 09 SET 10 SET 11 SET 12 SET 13 SET 14 SET 15 SET 16 SET 17 COLOR TEMPERATURE SET 18 SET 19 SET 20 SET 21 SET 22 SET 23 SET 24 SET 25 SET 26 SET 27 SET 28 SET 29 SET 30 SET 31 SET 32 BE 03 BE 04 BE 05 BE 06 BE 07 BE 08 BE 09 BE 0A BE 0B BE 0C BE 0D BE 0E BE 0F BE 10 BE 11 BE 12 BE 13 BE 14 BE 15 BE 16 BE 17 BE 18 BE 19 BE 1A BE 1B BE 1C BE 1D BE 1E BE 1F EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS SET 33 COLOR TEMPERATURE SET 34 SET 35 SET 36 SET ST1 SET EN1 SET EN2 SET EN3 GAMMA SET EN4 SET EN5 SET GR1 SET GR2 SET USER INCREMENT FREQUENCY DECREMENT INCREMENT PHASE DECREMENT INCREMENT Y/C DELAY DECREMENT INCREMENT MAGNIFICATION DECREMENT INCREMENT PAN HORIZONTAL DECREMENT INCREMENT PAN VERTICAL DECREMENT INCREMENT KEYSTONE VERTICAL DECREMENT KEYSTONE HORIZONTAL INCREMENT DECREMENT BE 20 BE 21 BE 22 BE 23 BE 0B BE 0D BE 0E BE 06 BE 07 BE 09 BE 0A BE
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS BE 01 BE 00 BE 00 BE 01 BE 02 BE 03 BE 04 BE 05 BE 00 BE 00 BE 00 BE 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 CB 00 5B 00 15 00 85 00 74 00 E4 00 D6 00 46 00 82 00 EC 00 7D 00 13 00 EB 00 2A 00 35 00 F4 00 B4 0
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS BE 03 BE 03 BE 01 RECALL SAVE CURRENT SETTINGS SAVE INITIAL SETTINGS MEMORY 3 EF 00 EF 00 EF 00 03 00 03 00 03 00 19 00 19 00 19 00 00 00 00 00 00 00 E4 00 35 00 A7 00 6A 00 57 00 E3 00 01 00 01 00 01 00 27 00 27 00 28 00 09 00 09 00 09 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 The response of the unit to a correct Operation Code consists of the byte 1E followed by a copy of t
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS Get Codes: (1) BRIGHTNESS BE EF 03 19 00 52 2A 02 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 CONTRAST BE EF 03 19 00 C7 77 02 01 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 COLOR BE EF 03 19 00 38 93 02 02 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 TINT BE EF 03 19 00 AD CE 02 03 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 COLOR TEMPERATURE BE EF 03
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS (5) Table below associates OSD labels with returned values: Gamma OSD Returned Label value 0B ST1 0D EN1 0E EN2 06 EN3 07 EN4 09 EN5 0A GR1 0C GR2 05 User (6) Table below associates OSD labels with returned values: Memory OSD Returned Label value 00 0 (Auto) 01 1 02 2 03 3 5. Examples 1. Send the simulated "SWITCH ON FROM STAND-BY" Remote Control keycode. Remote Control allows Switching on from Stand-by via the key "0".
SIM2 C3X LITE RS-232C CONTROL SPECIFICATIONS the code is: BEEF02060062E44B0100000000 5. Get "COLOR TEMPERATURE" Value for the Current Source Send the packet: BEEF0319009D0B02C20900000000000000000000000000000000000000000000 The unit returns the code: 1EBEEF031900C41F02C2090100000000000D000000000000000000000000000000 where bytes Number 17 and Number 18 (underlined above) carry the requested value. The returned value is 0D which corresponds to point 14 in the OSD Color Temperature chart. 6.