Owner’s Manual Evolution Series 760A Dual-Mono Power Amplifier
760A Dual-Mono Power Amplifier Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or another apparatus that produces heat. 9.
760A Dual-Mono Power Amplifier Important Safety Instructions (cont’d) The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
760A Dual-Mono Power Amplifier Table of Contents Introduction ..................................................... 6 Unpacking........................................................ 7 Installation & Placement ................................... 7 Rear Panel Layout ............................................ 8 Connecting the 760A ......................................... 9 Balanced Operation ........................................... 9 Bridged-Mono Operation ..................................
760A Dual-Mono Power Amplifier Introduction Thank you for selecting the MOON 760A DualMono power amplifier as a part of your hi-fi reproduction system. This power amplifier has been designed to offer state-of-the-art high-end performance in an elegant package, while retaining all the sonic hallmarks on which Simaudio has made its reputation. We have spared no effort to ensure that it is among the finest two-channel amplifiers available.
60A Dual-Mono Power Amplifier Unpacking The MOON 760A power amplifier should be removed from its box with care. The following accessories should be included inside the box with your amplifier: 9 AC power cable 9 This owner’s manual 9 Warranty and product registration information Once the 760A is unpacked, inspect it thoroughly and report any damage to your dealer immediately.
760A Dual-Mono Power Amplifier Rear Panel Layout Figure 1: Rear panel of Moon 760A Dual-Mono Amplifier The rear panel will look similar to Figure 1 (above). Each channel has one balanced (differential) input on an XLR connector and one unbalanced (singleended) input on a RCA connector. There is no switch to toggle from balanced mode to singleended mode. You may operate the amplifier in either mode, but only one mode at one time for each channel.
760A Dual-Mono Power Amplifier Connecting the 760A Prior to making any connections or removing the XLR jumpers, the power amplifier must be turned off and the AC cable disconnected for at least 1 minute. 1. Connect the input cables running from your preamplifier’s outputs, whether balanced or single-ended, to the amplifier’ s XLR or RCA inputs, respectively.
760A Dual-Mono Power Amplifier Bridged-Mono Operation Speaker From Preamp Figure 3: Bridged-Mono operation of the MOON 760A Dual-Mono Amplifier If wish to operate the MOON 760A Dual-Mono Power Amplifier as a monoblock amplifier, it can be converted to bridged mode without any complex modifications. Only a Simaudio XLR-BRIDGE Y-cable is required. This custom cable will allow one input signal to be sent to both channels of the amplifier’s inputs, as pictured above in Figure 3.
760A Dual-Mono Power Amplifier Operating the 760A We recommend leaving your 760A powered up at all times to maintain optimal performance. When you plan on being away for a few days, it may not be a bad idea to power off your amplifier. Please keep in mind that once fully “broken-in”, your 760A requires several hours of operation before reaching optimal performance after powering it up again.
760A Dual-Mono Power Amplifier Remote Operation Figure 4: Remote Operation with 12V Trigger In figure 4 we have a 740P Preamplifier and 760A amplifier connected together via their respective 12V triggers; The 12V trigger output on the 740P is connected to the 12V trigger input on the 760A (using a 1/8” mini-jack cable). When you turn on the 740P via remote control (or its Standby button), the 760A will turn on automatically. The same rule applies when you put the 740P into Standby mode.
760A Dual-Mono Power Amplifier Specifications Configuration ................................................ Power Supply Transformers ............................ Power Supply Capacitance ............................. Class Of Operation ........................................ Design ........................................................... Input Impedance .......................................... Input Sensitivity ............................................ Output Device Type ........................
