The First Name in Electronic Drums. SD9K Electronic Drum Kit user manual www.simmonsdrums.
FCC Statements 1. Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
www.simmonsdrums.net congratulations! Thank you for purchasing the Simmons SD9K Digital Drum Kit. We recommend that you take a quick look through this manual so you can enjoy all of the amazing features the SD9K has to offer. Taking Care of your digital drum kit Location • Keep the drum kit away from direct sunlight, high temperature sources, and excessive humidity to prevent deformation, discoloration, or more serious damage. Power Supply • Turn the power switch OFF when the SD9K is not in use.
SD9K digital drum kit User manual SD9K setup Set up your SD9K kit following the included assembly instruction sheet. 2 The First Name in Electronic Drums.
www.simmonsdrums.
SD9K digital drum kit User manual features Hardware Sturdy 4-Legged Drum Rack with Mounting Hardware Kick Pad 11” Dual-Zone Snare Pad 9” Tom Pad (x3) 11” Floor Tom Pad Dual-Zone Crash Pad with Choke (x2) 14” Dual-Zone Ride Pad with Choke Dual-Zone Hi-Hat Pad with Choke Hi-Hat Control Pedal Drum Kits 100 Drum Kits: (40 Preset Kits + 59 User Kits + 1 External MIDI Kit) General MIDI Kits: 12 GM Kits Instruments 725 Drum Voices: (Drums, Percussion, SFX) + 19 Hi-Hat Combos General MIDI Backing Voices: 128
www.simmonsdrums.net operation The SD9K has two main modes of operation: KIT and SONG. Each mode has three sub-modes (sub-menus): EDIT, MIX and UTILITY, plus a SAVE menu. KIT mode: In the main KIT mode, you can select a preset or user KIT to play from the pads. In KIT / EDIT sub-mode, you can select the Voice for each pad, and adjust its Tuning (Pitch) and Decay. In KIT / MIX sub-mode, you can adjust the Level, Pan and Reverb Level for each pad, as well as the Global Reverb Type and Equalization.
SD9K digital drum kit User manual control panel 8 5 2 6 3 7 21 19 23 20 22 18 1 17 24 16 4 15 9 14 10 13 12 11 LCD SCREEN AND NAVIGATION SUB-MENU SECTION SONG SECTION DATA ENTRY SECTION KIT SECTION 6 The First Name in Electronic Drums.
www.simmonsdrums.net 1 2 3 4 5 6 7 8 9 10 11 12 VOLUME CONTROLS: MAIN OUT Volume knob Controls the volume of the Stereo Line output. PHONES ( ) Volume knob Controls the volume of the Phones output. CLICK Volume knob Controls the volume of the Metronome. AUX IN Volume knob Controls the volume of the Stereo Auxiliary input. LCD NAVIGATION: LCD Screen Please refer to the LCD Screen section. PAGE buttons Scrolls through the menu pages, or moves the cursor left/right when naming.
SD9K digital drum kit User manual SD Card Slot About the SD Card Reader: The SD9K is equipped with an SD Card Reader, located in front of the sound module. Insert the card, terminal face up, as shown on the top panel graphic icon ( ). Push the card all the way in, until it clicks in place. To remove the card, push the card in again until it clicks and pops out. Now you can pull the card out. NOTE: Never touch the terminal of the SD Card.
www.simmonsdrums.net lcd screen The LCD (Liquid Crystal Display) screen is divided into two areas: INFO LINE MAIN DISPLAY Info Line: The top line of the LCD display always shows the same information, regardless of current mode/menu. KIT • Kit number: Shows current active kit number. • USER icon: Shows if the current kit is a User Kit. • EDIT icon: Shows if the current kit has been edited and not saved. SONG • Song number: Shows current active song number.
SD9K digital drum kit User manual NAMING Pad Input Jacks Input connections for Kick, Snare, Tom, AUX, Cymbal pads, and Hi-Hat control pedal. MIDI In and Out These ports allow communication with other products equipped with a MIDI interface. Please see the MIDI section of the advanced manual for details. USB port This port is used to connect to a computer (MIDI In/Out via USB). Line output jacks Stereo output connection to an audio system or drum amplifier such as the Simmons DA50 or DA200S.
www.simmonsdrums.net connection panels rear panel 1 Pad input jacks Input connections for Kick, Snare, Tom, AUX, Cymbal pads, and Hi-Hat control pedal. 2 MIDI IN and OUT These ports allow communication with other products equipped with a MIDI interface. Please see the MIDI section on page 48 for details. 3 USB port This port is used to connect to a computer (MIDI In/Out via USB).
SD9K digital drum kit User manual connections pads and pedals CAUTION! To avoid damage, turn the SD9K and all related devices OFF prior to connecting or disconnecting cables. Pads and Pedal: Using the provided cables, connect each pad to its corresponding trigger input jack, following the markings on the cables. The underlined trigger input names show which inputs use TRS (stereo) cables. Secure all cables to the stand using the provided cable clips.
www.simmonsdrums.net POWER SUPPLY Make sure the power is switched OFF. Connect the power adapter to the DC IN jack on the rear panel. Right Side Panel POWER SWITCH Right Side Panel After confirming that all connections have been completed, rotate the volume knob to the left (minimum volume level) before switching the power ON. Set the power switch to the “ON” position. The Kit indicator will light up and the display will show Kit number 001.
SD9K digital drum kit User manual getting started After powering up, the SD9K will be in KIT mode. Kit indicator shows the first Kit selected. The display should look like this: Use the Data wheel or the [+] / [–] buttons to select the active Kit. Pressing the Pad Select buttons allow you to preview the current Kit (fixed velocity). Hit the pads to play the current Kit. NOTE: Hitting the pads always triggers the current Kit, even when the SD9K is not in KIT mode.
www.simmonsdrums.net Click The SD9K is equipped with a built-in metronome, which can be used by itself as a rhythm guide for practice, or in conjunction with the Song playback/record functions. The metronome is controlled by the [CLICK] button. Press the [CLICK] button to start the metronome. The Click indicator will light up. The metronome will play at the current Time Signature and Tempo (displayed in the top right corner of the LCD), and the Beat indicators will blink accordingly.
SD9K digital drum kit User manual TEMPO Tempo is a global setting across all of the SD9K’s features. Press the [TEMPO] button to enter the Tempo adjustment screen: This screen is used to adjust the tempo of the Metronome, the current Song or a MIDI file on an SD card. The tempo range is 30 – 280 beats per minute. Use the Data Wheel or [+] / [-] buttons to adjust tempo. Press [+] and [-] together to reset the tempo to default.
www.simmonsdrums.net Kit mode In KIT mode you can select Drum kits, in addition to editing Kit Voices and their associated parameters such as Pitch, Decay, Level, Pan, etc. There are 100 kits in the SD9K: • 40 preset kits (Kits 01-40) • 59 user kits (Kits 41-99) • 1 external kit (Kit 00). This special kit is intended to use the SD9K to trigger external drum sound generators via MIDI or USB, with no internal sound playback.
SD9K digital drum kit User manual Kit Parameters The SD9K’s parameters can be adjusted to customize the kit to your own preferences. Preset Kits 01-40 are fixed, but they can also be used as starting points to be edited and saved as User Kits. The parameters in KIT mode are divided into several categories. Pad Voice, Edit, and Mix parameters affect each individual drum voice. Kit Mix parameters affect all Internal Kit voices.
www.simmonsdrums.net Kit Select If the SD9K is not yet in KIT mode, press the [KIT] button to enter it. The Kit indicator will light up, and the LCD will display the current kit number and name. Use the data wheel or the [+] / [-] buttons to select a kit, and/or the [PAGE UP] / [PAGE DOWN] buttons to quickly skip through kit groups (preset kits, user kits, or external kit). In KIT menu: • Press the [EDIT] button to edit Pad Voices of the current kit (or MIDI parameters of the External Kit).
SD9K digital drum kit User manual Kit Edit In KIT mode, when an internal kit (Preset or User) is selected, pressing the [EDIT] button enters the KIT EDIT mode for the last selected pad. Another pad can be selected by hitting it or pressing its Pad Select button. You can preview the voice at any time by pressing the Pad Select button again. The SD9K includes 725 voices sorted by groups (Kick, Snare, Tom, Cymbal, Hi-Hat, Percussion, etc.) See Voice List in appendix for a complete catalog.
www.simmonsdrums.net Kit Band In KIT mode, when an internal kit (Preset or User) is selected, pressing the [MIX] button enters the KIT MIX mode. The first page of KIT MIX allows you to mix Pad, Kit, Reverb or EQ. As with any parameter, the value can be changed using the data wheel or the [+]/[-] buttons. Alternatively, this first parameter can also be changed by pressing the [EDIT] button repeatedly. MIX Pad Mix allows you to adjust the Level, Pan, and Reverb levels to your specifications.
SD9K digital drum kit User manual MIX Kit If Mix: Kit sub-menu is selected, the display will show: The name of the current Kit is also displayed. Press the [PAGE DOWN] button to access the next parameter, Kit Level. This parameter adjusts the overall Kit level (0 – 32). MIX Reverb If Mix: Reverb sub-menu is selected, the display will show: The name of the current Kit is also displayed. Press the [PAGE DOWN] button to access the next parameter, Reverb Switch.
www.simmonsdrums.net External kit Use this feature when you want to use the pads as a means to generate sounds from an external sound module. The External Kit allows the SD9K to trigger external drum sound generators via MIDI or USB. In KIT mode, when the External Kit (00) is selected, pressing the [EDIT] button enters the External KIT EDIT mode, for the last selected Pad. Another Pad can be selected by hitting it or pressing its [PAD SELECT] button.
SD9K digital drum kit User manual Kit Save Save To User Kit After changing any Kit Edit or Mix parameters (EDIT sign is lit), press the [SAVE] button to enter the Save menu. Values 41-99 shows current User Kit name. Press [PAGE DOWN] to access the next parameter. Naming screen defaults to original name of the Kit being edited. [PAGE] buttons act as cursor left/right. Use the data wheel or [+]/[-] buttons to change value. Press the [SAVE] button to save the user kit.
www.simmonsdrums.net Kit Utility Menu: Global Parameters Pad Parameters This section of the menu allows you to modify pad, MIDI, factory reset, and prompt operations. Press [UTILITY] to enter this menu. The first section lets you choose which Utility sub-menu to edit, with the first choice being Pad. Type Tells the SD9K what type of pad is connected. To access the next global parameter, press the [PAGE DOWN] button. Sensitivity Changes how a pad responds to your playing.
SD9K digital drum kit User manual MIDI parameters The next Utility sub-menu affects global MIDI parameters. NOTE: To access the next MIDI parameter, press the [PAGE DOWN] button on the system’s console. Sync Turn this feature on when you want to sync the SD9K’s playback to other sequencers. Press the [PAGE DOWN] button to access the next parameter. Local ON: The pads will generate sounds and the module sends out MIDI information. OFF: The pads will send out MIDI information only.
www.simmonsdrums.net factory reset The next Utility sub-menu lets you restore the SD9K to its factory default settings. Press [+] if you wish to reset, or [–] to exit. prompt operation The next Utility sub-menu controls the Prompt feature. Press the [SONG] or [CARD] button, or select a new Kit to exit the KIT EDIT menu. ON indicates to save, while OFF sends the operation, with the data lost. 27 The First Name in Electronic Drums.
SD9K digital drum kit User manual SONG Mode The SONG mode is where you can select and edit songs to play, as well as record new songs. There are 211 songs in the SD9K: • 110 preset songs (Songs 001-110) divided into 3 groups: - 60 Looped Patterns - 30 One Shot Songs - 20 Drum & Percussion Loops • 100 user songs (Songs 111-210) • 1 external song (Song 000). This special song is intended for using the SD9K to control an external sequencer via MIDI or USB (no internal song playback).
www.simmonsdrums.net song play Press the [PLAY] button to play the current song. The Play indicator will light up, Beat indicators will flash at the current tempo and signature, and the LCD will display the song's measure and beat. Press the [PLAY] button again to pause the song at the current measure. Press the [PLAY] button once more to resume playback from the head of the paused measure. Press the [STOP] button to stop the song and return to the first measure.
SD9K digital drum kit User manual song edit In SONG mode, press the [EDIT] button to enter the Song Edit menus. The Edit indicator will light up. The first page of Song Edit selects the Edit sub-menu: Song, Drums, Percussion Parts 1 through 5. As with any parameter, this selection can be made using the data wheel or the [+]/[-] buttons. Alternatively, this sub-menu can also be changed by pressing the [EDIT] button repeatedly. The first option is Global Song parameters.
www.simmonsdrums.net part parameters Each song has 7 tracks (or parts): drums, percussion, and parts 1 through 5. Each track’s parameters can be edited. Press [EDIT] to enter the Song Edit menus. Press [+]/[-] or [EDIT] buttons repeatedly to select a part, then press [PAGE DOWN] to enter the parameter sub-menu. Press [PAGE DOWN] to edit the track's voice.
SD9K digital drum kit User manual song mix In SONG mode, press the [MIX] button to enter the Song Mix menus. The MIX indicator will light up. The first page of Song Mix selects the Mix sub-menu: Accomp, Percus, Parts 1 through 5. As with any parameter, this selection can be made using the Data wheel or the [+]/[-] buttons. Alternatively, this sub-menu can also be changed by pressing the [MIX] button repeatedly. The first option is Global Accompaniment Level.
www.simmonsdrums.net song erase This Utility menu allows you to erase the current song or a specific part of the song. This only applies if the selected song is a User Song that is not empty. To access the Song Erase menu in SONG mode, press the [UTILITY] button. The Utility indicator will light up. Press the [+] button or the [UTILITY] button again to select the Erase option: Press [PAGE DOWN] to enter the Erase sub-menu. Use the data wheel or [+]/[-] buttons to select a Song or its part to be erased.
SD9K digital drum kit User manual song record The SD9K allows you to record your own user songs by recording a new song from scratch, or by replacing/adding parts on an existing song. You can record data generated when playing the pads. The Percussion part and/or Instrument parts 1 through 5 can be recorded using a MIDI controller (keyboard or multi-pad controller) connected to the MIDI Input. Record a New Song There are two ways to record a new song: One-Click Recording or New Song record.
www.simmonsdrums.net Press the [STOP] button to stop playback. The PLAY LED will turn off, the RECORD LED will turn on and the display will show: If you are not satisfied with your recording, press the [RECORD] button to restart the recording process. When you are satisfied with your recording, press the [EXIT] button to exit RECORD mode. The PLAY and RECORD LEDs will turn off. The message “Save Song OK!” briefly appears, and you will then be returned to the main SONG mode display.
SD9K digital drum kit User manual New Song Record If you want more options to record a new User Song, use the New Song function. In SONG mode, press the [UTILITY] button to access the New Song sub-menu. NOTE: The current song can be any type of song, except External Song 00. Press [PAGE DOWN] to enter the New Song sub-menu. Press [PAGE DOWN] to set your Tempo. Press [PAGE DOWN] to set your Time Signature. Press [PAGE DOWN] to toggle Loop on or off. Press [PAGE DOWN] to set your Song Length in bars.
www.simmonsdrums.net Once you have saved your new song, the REC indicator will light up and the first Record menu page will appear, which allows you to select which part you can record to. Use the Data wheel or the [+]/[-] buttons to select the part. Icons are displayed to indicate if LOOP mode is On ( ) and/or if any Quantize is active on the select part. Press [PAGE DOWN] if you want to change the Quantize option. Press [PAGE DOWN] to choose your kit.
SD9K digital drum kit User manual When the metronome begins to count, start playing the pads. NOTE: When recording with the [PLAY] button, a count-in precedes recording as defined in the Click menu (R Count: OFF< 1 Bar, or 2 Bars). When recording by playing the pads/MIDI, recording will start immediately. If the Song is in LOOP mode, you can overdub the same section at each pass of the loop. If you want to try adding to the part without actually recording, press the [PLAY] button.
www.simmonsdrums.net card menu The SD9K is equipped with an SD Card reader, located in front of the sound module. The SD Card provides the following features: • Play standard MIDI File (SMF, 16-track) direct from Card • Save/Load SD9K data: User Kits, User Songs, Global Setup • Updatable software (for future improvements) To enter the CARD menu, press the [CARD] button, and the Card indicator will light up.
SD9K digital drum kit User manual saving sd9k data to card You can save various SD9K data to an SD Card for backup or to exchange data with other users. On one SD card, you can save up to 256 User Kits and 256 User Songs. The maximum file name length on the SD Card is eight characters. NOTE: If you attempt to save a file with a name that already exists on the card, the screen will briefly show “Same Name!” and return to the file naming screen.
www.simmonsdrums.net Saving Songs Select Card — Save. Press [PAGE DOWN] to select the type of file to save. To save a single song, select Type — Song. To save all Songs as one file, select Type — AllUSongs. Press [PAGE DOWN] to go to the Song file naming page. Use the Data wheel or [+]/[-] buttons to change characters and the [PAGE] buttons to move the cursor. NOTE: When saving a single Song, the current Song is automatically selected, and the file name defaults to the Song name.
SD9K digital drum kit User manual Saving Setup You can save SD9K setup data to the card. Setup data includes global settings such as Pad, Click, MIDI, etc. Select Card — Save. Press [PAGE DOWN] to select the Type of file to save. To save a setup file to card, select Type — Setup. Press [PAGE DOWN] to go to the Setup file-naming page. Use the Data wheel or the [+]/[-] buttons to change characters and the [PAGE] buttons to move the cursor. Press [+] to save or [-] to cancel.
www.simmonsdrums.net loading sd9k data from card Loading Kit Data Select Card — Load option. Press [PAGE DOWN] to select the type of file to load. To load a single kit from the Card to a User Kit, select Type — Kit. To load all Kits, select Type — AllUKits. Press [PAGE DOWN] to go to the Kit file selection page. Use the Data wheel or the [+]/[-] buttons to scroll through Kit files. Note: An icon shows the type of Kit file: (Internal Kit), (External Kit), and (All Kits).
SD9K digital drum kit User manual Loading Song Data You can load song data from an SD Card, either from the SD9K songs saved to the SD Card or from other Standard MIDI files (*.mid) created or edited using other sequencers. If you want to load your own MIDI file to an SD9K user song, you must put the file into the USERSONG folder, and the file must meet certain requirements: • MIDI File Format: Type 1 • Resolution: from 24 to 1024 PPQN • Tracks: 7 max.
www.simmonsdrums.net Press [PAGE DOWN] to go to the User Song destination page (only when loading a single song). Use the Data wheel or the [+]/[-] buttons to select the User Song file number you wish to load. NOTE: If you have selected an External Song file, it can only load into Song 00. When loading an All Songs file, all user songs – including the external song – will be replaced by new data. Press [PAGE DOWN] to go to the Load confirmation page. Press [+] to load or the [-] to cancel.
SD9K digital drum kit User manual Deleting Files From Card You can only delete SD9K files from the SD Card (i.e. Kits, Songs, Setup, MIDI Files). If there are other types of files stored on the card, the SD9K will not detect them and therefore will not be able to delete them. Select Card — Delete. Press [PAGE DOWN] to open the root directory of the card. Use the Data wheel or the [+]/[-] buttons to scroll through Folders and MIDI Files. NOTE: Folders are indicated by a Folder icon Song icon . .
www.simmonsdrums.net Formatting the SD Card Select Card — Format. Press [PAGE DOWN] to go to the Format confirmation page. Press [+] to continue or [-] to cancel. For file safety, the SD9K will prompt you a second time. Press [+] to format or [-] to cancel. NOTE: All card data (SD9K files and other files) will be lost after formatting. Proceed with caution! 47 The First Name in Electronic Drums.
SD9K digital drum kit User manual MIDI and USB MIDI stands for Musical Instrument Digital Interface. This worldwide standard communication interface enables electronic musical instruments and computers of all brands to communicate and pass instructions and other data back and forth. This exchange of information makes it possible to create a system of MIDI instruments and devices that offers far greater versatility and control than what is available with isolated instruments.
www.simmonsdrums.net MIDI channels MIDI OUT The SD9K transmission channel for the Drum Kit is fixed to Channel 10. The SD9K will output MIDI codes generated by the triggers when hitting the pads or stepping on the Hi-Hat control pedal (Note On/Off, and Foot Control messages). The SD9K will also transmit Program Change messages when selecting Kits. SD Card MIDI File playback data and Metronome notes are not transmitted. If Part Output is set to Internal, Song playback data for that Part is not transmitted.
SD9K digital drum kit User manual Using THE sd9k to control a sequencer In SONG mode, when the External Song 000 is selected, the SD9K can control the playback of an external sequencer. The MIDI clock (0xF8) is sent out automatically at the current tempo, and Start and Stop Real-Time Commands (0xFA, 0xFC) will be sent when pressing the Play/Stop buttons. 1. Connect the MIDI Out of the SD9K to the MIDI In of your sequencer.
www.simmonsdrums.net mute function Press the [MUTE] button to toggle the MUTE function. The Mute indicator will light up when MUTE is enabled and turn off when MUTE is disabled. The default MUTE function is drums off (Channel 10 Muted), but this can be changed to any combination of channels in the MUTE setup menu. To enter the Channel MUTE setup, hold down the [MUTE] button for 3 seconds. The Mute indicator will light up (with MUTE function enabled).
SD9K digital drum kit User manual appendices • Voice List • HI-Hat Combo List • Kit List • Song List • General MIDI Kit List • General MIDI Voice list • MIDI Implementation Charts (Drums module, GM module, Sequencer) 52 The First Name in Electronic Drums.
www.simmonsdrums.
SD9K digital drum kit User manual voice list # Name # # Name 216 Simmons SD5 C Snare Electronic Snare 217 Simmons SD5 D Snare 162 House Snare 1 218 Simmons SD7 A Snare 163 House Snare 2 219 Simmons SD7 B Snare 164 Step Snare 220 Simmons SD9 A Snare 165 Step Snare Cross Stick 221 Simmons SD9 B Snare 166 Techno Snare 1 222 Simmons SD9 C Snare 167 Techno Snare 2 223 Simmons SD9 D Snare 168 606 Snare 169 808 Snare Acoustic Tom 170 808 Snare Cross Stick 224 Open Tom 1 171 909 Snare 225 Open Tom 2 172 In
www.simmonsdrums.
SD9K digital drum kit User manual voice list # 601 602 603 604 605 607 608 606 609 610 611 612 613 614 615 616 617 618 619 620 621 Name Surdo Open Taiko Lotus Drum Rain Stick Slap Stick Open Tabla High Tabla Mute 1 Open Tabla Low Open Tabla Mid Slap Tabla Tabla Mute 2 Tabla Bend Gong Timpani High Timpani Low Piatti Cymbal Gran Cassa and Piatti Orchestra Hit Techno Hit Horns Hit Voice Hit Melodic 622 Glockenspiel 623 Music Box 624 Vibraphone 625 Marimba 626 Xylophone 627 Tubular Bell 628 Steel Drum SFX
www.simmonsdrums.
SD9K digital drum kit User manual SONG LIST Pattern Loop One Shot # Name Beat Tempo Measure # Name Beat Tempo Measure 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Funk1 Latin Jazz1 Pop Funk1 Latin Rock Big Band1 Pop Ballad Pop Funk2 3/4 Jazz Pop Bossa Samba1 6/8 Ballad1 Fusion1 Jazz1 Guitar Bossa Break Beat1 Smooth Jazz1 Funk2 Smooth Jazz2 Latin Pop Reggae1 Fusion2 Swing
www.simmonsdrums.
SD9K digital drum kit User manual GENERAL MIDI KIT LIST Percus Kit GM PC 01: Standard 1 00 02: Standard 2 04 03: Room 08 04: Rock 16 05: Funk 17 06: Electronic 24 27 D#1 28 E1 29 F1 30 F#1 31 G1 32 G#1 33 A1 34 A#1 35 B1 36 C2 37 C#2 38 D2 39 D#2 40 E2 41 F2 42 F#2 43 G2 44 G#2 45 A2 46 A#2 47 B2 48 C3 49 C#3 50 D3 51 D#3 52 E3 53 F3 54 F#3 55 G3 56 G#3 57 A3 58 A#3 59 B3 60 C4 61 C#4 62 D4 63 D#4 64 E4 65 F4 66 F#4 67 G4 68 G#4 69 A4 70 A#4 71 B4 72 C5 73 C#5 74 D5 75 D#5 76 E5 77 F5 78 F#5 79 G5 80
www.simmonsdrums.
SD9K digital drum kit User manual MIDI IMPLEMENTATION CHART (DRUMS) Function Basic Channel Default Changed Default Mode Messages Altered Note Number True voice Velocity Note on Note off After Keys Touch Channels Pitch Bend Control 0 1 6 7 10 11 64 66 67 80 81 91 93 100, 101 Program Change System Exclusive System : Song Position Common : Song Select : Tune System : Clock Real Time : Commands AUX : Local ON/OFF Messages : All Sound Off : Reset All : Controllers : All Notes Off : Active Sense : Reset Trans
www.simmonsdrums.
SD9K digital drum kit User manual MIDI IMPLEMENTATION CHART (SEQUENCER) Function Basic Channel Default Changed Default Mode Messages Altered Note Number: True Voice Velocity: Note on Note off After Keys Touch Channels Pitch Bend Control 0 1 5 6 7 10 11 64 65 66 67 80 81 91 93 100, 101 Program Change System Exclusive System : Song Position Common : Song Select : Tune System : Clock Real Time : Commands AUX : Local ON/OFF Messages : All Sound Off : Reset All : Controllers : All Notes Off : Active Sense :
For more details on your Simmons® SD9K Digital Drum Kit, visit www.simmonsdrums.net and download a PDF version of this manual.
The First Name in Electronic Drums. Full-featured drum kits, advanced practice pads, hybrid kits, versatile amps and more. SDHB2 HYBRID DRUM KIT Expand your acoustic drum kit with digital sounds. Includes two 9” pro pads, two piezo triggers, and all the cables you need. Module includes 300 voices, 20 present kits, 30 user kits and USB connectivity. SD9K ELECTRONIC DRUM SET Sleek-looking module includes 725 voices, 40 preset kits, and room for an additional 59 user kits.
