Fire 4100ES-S1 Fire Indicator Panel Installation & Maintenance Australian Australian Installation Installation & Maintenance Manual Manual LT0394 Issue 1.
Copyrights and Trademarks 2006, 2014 Tyco Australia Pty Limited. All Rights Reserved. All specifications and other information shown were current as of document revision date, and are subject to change without notice. Tyco, Simplex, the Simplex logo, MAPNET II, IDNet, TrueAlarm, SmartSync, WALKTEST, MINIPLEX, and TrueAlert are trademarks of Tyco International Services AG or its affiliates in the U.S. and/or other countries. VESDA is a trademark of Xtralis.
Non-Disclosure Agreement Tyco (THE COMPANY) and the User of this/these document(s) desire to share proprietary technical information concerning electronic systems. For this reason the company is disclosing to the User information in the form of this/these document(s).
Model Number & Firmware Revision This manual applies to product with the following: Model number : 4100ES-S1 Firmware revision : 1.02.04 and on Document Document Name : LT0394 4100ES-S1 Installation & Maintenance Manual Issue : V1.9 24 Feb 2015 Amendment Log 5 July 2006 Issue 1.0 Original based on LT0350 1.0.7 6 October 2006 Issue 1.1 References to LT0432 and 1976-181 Wiring Diagrams added. 30 Nov. 2006 Issue 1.2 Updated drawings 1976-181 Sheets 102, 203, 500. 23 Jan. 2007 Issue 1.
Cautions, Warnings, and Regulatory Information READ AND SAVE THESE INSTRUCTIONS. Follow the instructions in this installation manual. These instructions must be followed to avoid damage to this product and associated equipment. Product operation and reliability depends upon proper installation. DO NOT INSTALL ANY SIMPLEX® PRODUCT THAT APPEARS DAMAGED. Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage.
Table of Contents{ XE "Table of Contents" } Copyrights and Trademarks.......................................................................................... iii Approvals...................................................................................................................... iii Manufacture.................................................................................................................. iii Product / Site .......................................................................
Step 1. Mounting Cabinets ........................................................................................ 2-9 Overview ................................................................................................................ 2-9 Step 2. Mounting Card Bays to Cabinets ................................................................... 2-9 Overview ................................................................................................................ 2-9 Step 3. Configuring Cards ....
NIC Media Cards ................................................................................................... 3-6 Requirements and Limitations................................................................................ 3-7 Step 1. Configuring Network Cards ........................................................................... 3-7 Overview ................................................................................................................ 3-7 CPU Motherboard Jumper Settings .......
Format ................................................................................................................... 4-9 Applications ........................................................................................................... 4-9 Kit Contents ........................................................................................................... 4-9 Door Mounting .......................................................................................................
Chapter 6 Using Install Mode............................................................. 6-1 Introduction ............................................................................................................ 6-1 In this Chapter ....................................................................................................... 6-1 Adding Devices to Install Mode.................................................................................. 6-2 Adding a Single Device to Install Mode ............
Appendix D Earth Fault Detection ..................................................... D-1 Overview ................................................................................................................ D-1 General Guidelines .................................................................................................... D-2 Earth Fault Searching from the Front Panel ............................................................... D-3 Overview ...................................................
List of Figures{ XE "List of Figures" } Figure 1-1. Basic 4100ES-S1 System ........................................................................... 1-2 Figure 2-1. CPU Motherboard (566-227) ...................................................................... 2-3 Figure 2-2. CPU Card (566-719) .................................................................................. 2-4 Figure 2-3. Operator Interface ......................................................................................
{ XE "List of Figures" }List of Tables{ XE "List of Figures" } { XE "List of Tables" } Table 2-1 Table 2-2 Table 2-3 Table 2-4 Table 3-1 Table 3-2 Table 3-3 Table 3-4 Table 3-5 Table 4-1 Table 4-2 Table 4-3 Table 5-1 Table 5-2 Table A-1 Table C-1 Master Controller LEDs 1 through 4 ............................................ 2-5 Switch/LED Format ................................................................... 2-22 Switch Status ..........................................................................
Chapter 1 Introduction to the 4100ES-S1 Fire Alarm System Introduction The 4100ES-S1 is a compact version of the 4100ES fire alarm, which is intended for use in applications requiring only one or two loops of addressable devices. This chapter is an overview of basic system concepts. {xe "4100 Fire Alarm System"} In this Chapter Refer to the page number listed in this table for information on a specific topic.
Basic Configuration Overview The basic version of the 4100ES-S1 is used for smaller or single-building applications. It is ideally placed in a small building that requires a limited number of notification appliances and initiating devices.
4100ES-S1 Part Codes Overview This section lists the parts that are supported by the 4100ES-S1 Fire Alarm System. Assemblies, Cards & & Modules The following is a list of assemblies, cards and modules used in 4100ES-S1: These parts are included in the base 4100ES-S1: 742-516 CPU Motherboard (566-227) 4100-7158 CPU Card (566-719) 4100-9848AU System Power Supply, Australian version 4100-6033 Alarm Relay Card (566-058) plugged onto the SPS and used to supply the Brigade I/F relays.
4100ES-S1 Part Code, Continued Labels (expansion/spares) Looms (expansion/spares) LB0602 Operator I/F ISO/Test Card LB0605 Fan Control Zone Insert Card 526-873 Slide In Label, LED Switch Module, 1 Sheet of 6 4100-1294 LED Module Slide In Labels, Panel Set LM0309 4100U Mains Lead With Filter LM0310 4100U Battery Lead Set, 18U-21U 734-008 Harness, Power Comms, 4 Way, 2ft Length 734-075 Harness, Power Comms, 4 Way, 8ft Length 116-226 Sw/LED Module Ribbon Cable, 26
Glossary AZF Alarm Zone Facility – means of grouping multiple detectors or devices, and providing common indication and control. Class A Wiring Method of connecting multiple devices or units in a loop. This requires up to twice as much wire but means that a short or open circuit in any one section will not prevent communication with every device.
1-6
Chapter 2 Installing 4100ES-S1 Components Introduction This chapter describes how to mount the 4100ES-S1 cabinet to a wall, and how to mount system card bays into the cabinets, modules to bays, etc. Most of a 4100ES-S1 is already assembled within the factory. Steps 2 to 6 below are therefore not typically required in the field, but are included for reference. The assembly drawings are included in the appendix of this manual for reference.
Introduction to 4100ES-S1 Cabinet Overview The 4100ES-S1 cabinet contains the CPU, operator interface, system power supply (SPS), backup batteries, and any additional modules that the panel requires. Bays These items are organized into sub-assemblies called bays or card frames, each with a swing-down front door. The 4100ES-S1 has two bays: the CPU bay and one expansion bay. In the standard 4100ES-S1, the CPU bay contains the SPS and the CPU Motherboard with CPU Daughter card.
Introduction to 4100ES-S1 Cabinet, Continued CPU Motherboard The 4100ES CPU motherboard (see Figure 2-1) holds the CPU card, which is central to the 4100ES-S1 system. It is mounted in the CPU bay, occupying two slots of space immediately beside the power supply. This board does not have a card address DIP switch (the CPU is always address 0).
Introduction to 4100ES-S1 Cabinet, Continued CPU Card The CPU card (see Figure 2-2) mounts onto the CPU motherboard. The CPU card contains an Ethernet service port, a direct drive user interface connection, and a serial port for a service modem. {xe "CPU daughter card: about"}{xe "4100U: CPU daughter card"} Figure 2-2.
Introduction to 4100ES-S1 Cabinet, Continued CPU Card LEDs The CPU card LEDs indicate Bootloader status as shown in Table 2-1. Table 2-1. CPU Card LEDs 1 through 4 Status Condition LED D LED C LED B LED A On (0.25s), Off (0.25s) On (0.25s), Off (0.25s) On (0.25s), Off (0.25s) On (0.25s), Off (0.
Introduction to 4100ES-S1 Cabinet, Continued Operator Interface The operator interface (see Figure 2-3) lets a user operate the panel. It provides alarm, fault, and isolate status alerts, and lets the user review historical logs and perform diagnostics. Figure 2-3. Operator Interface Additional CPU Motherboard Modules System Power Supply (SPS) 4100-6014 Modular Network Interface Card (NIC). A daughter card that mounts to the CPU motherboard. Performs 4100 networking operations.
Introduction to 4100ES-S1 Cabinet, Continued The basic 4100ES-S1 has a Fuse Distribution Board mounted on the SPS chassis and connected to the Auxiliary Power terminals. See Figure 2-4. This provides four sets of supply terminals, each individually fused at 1A, but the collective capacity is still limited to 2A from the Auxiliary Power supply. The fuses are not directly supervised.
Introduction to 4100ES-S1 Cabinet, Continued The Power Distribution Interface (PDI) POWER/COMMS CONNECTORS (P1-P3) In the expansion bay, power and data are distributed via the power distribution interface (PDI). The PDI is a wiring board (see Figure 2-5) with eight card slots, each of which can accommodate a 4-inch (102 mm) x 5-inch (127 mm) slave card. If 4100-style motherboards are used, they must be mounted over the PDI using a kit of metal standoffs (part number 4100-KT0468).
Step 1. Mounting Cabinets Overview The important aspects of mounting the cabinet are: Access for the operator; Height of displays and controls; Free space for door opening; Cable entry for field wiring. Refer to AS 1670.1 for the height requirement and minimum access requirements. In general, 4100ES-S1 cabinets will be wall mounted. There are four dimpled mounting holes in the rear of the cabinet.
Step 3. Configuring Cards, Continued Note: Some devices that connect to RUI have inherently grounded shield terminals, in which case 24 C cannot be used. If 24 C is used, a Negative Ground Fault will occur. P10/P11: P10 is associated with Port 1 and P11 is associated with Port 2. P10 and P11 are used to set the CPU motherboard up to be attached to either a network card or a RS232/2120 card. Position 1 – 2: Network card (NIC) plugged into CPU motherboard (default).
Step 4. Interconnecting Modules and Bays {xe "4100U: card configuration"} Overview Each card has to be interconnected with every other card in its bay. At the same time, bays in the 4100ES-S1 also have to be connected together. Read this section to ensure that cards and bays are interconnected correctly. Refer also to drawings 1976-136 and 1976-137. The basic 4100ES-S1 will have all necessary interconnection wiring already fitted, but additional wiring may be necessary if expansion modules are fitted.
Step 4. Interconnecting Modules and Bays, Continued Connecting to Motherboards Panels with legacy motherboards in the expansion bay require some non-PDI connections. If you need to connect a harness to a motherboard, refer to Figure 2-6 and follow these steps. Make sure to route the power and communication wiring on the left side of the bay. 1. Connect one end of the 733-525 Harness to a motherboard in the CPU bay.
Step 5. Installing Modules into Expansion Bays Overview This section contains guidelines and instructions on installing 4”x 5” cards and traditional motherboards into the 4100ES-S1 expansion bay. IMPORTANT: This section applies to aftermarket modules for expansion bays only. If you do not need to install any aftermarket modules at all, you have completed the panel installation and can apply AC power. Refer to the following guidelines before mounting 4” x 5” cards and/or motherboards to the expansion bay.
Step 5. Installing Modules into Expansion Bays, Continued Motherboards can be installed on top of the PDI in expansion bays. The data and power that would normally be bussed via the PDI are routed across the motherboards via their left and right connectors (J1 and P1). Up to four 2” (51 mm) x 11 ½” (292 mm) motherboards can be installed in an expansion bay if the pins on the left connector (usually P1) on the leftmost motherboard are removed. See Figure 2-8.
Step 5. Installing Modules into Expansion Bays, Continued {xe "mounting: modules to 4100U back boxes"} Installing 4” X 5” Cards The power distribution interface (PDI) is mounted to the back of the expansion bay. See Figure 2-9. The PDI contains slots for up to eight 4”x 5” slave cards. Since the PDI carries power and data across the entire bay, it solves most interconnection issues, especially between 4”x 5” cards.
Step 5. Installing Modules into Expansion Bays, Continued {xe "mounting: motherboards to 4100U back boxes"} Installing Motherboards Use the following procedure when installing motherboards in an expansion bay. Start with the third slot from the left and fill to the right. The mounting items are available as kit 4100-KT0468. 1. Orient the motherboard with the connector labeled J1 on the right and the header labeled P1 on the left. 2.
Step 6. Installing LED/Switch Modules into Expansion Bays Overview The LED/switch user interface consists of a variety of modules, mounted to the front of an expansion bay, which are configured via the 4100ES Programmer. Each display module contains between 8 and 24 switches and LEDs, each one separately configurable. User interface functionality is driven by the 64/64 LED/Switch Controller Card, which mounts behind two of the display modules (in positions 1 and 2).
Step 6. Installing LED/Switch Modules into Expansion Bays, Continued Figire 2-11shows an LED/switch bay from the user’s perspective. The LED/Switch User Interface Figure 2-11. LED/Switch Modules The LED/switch controller card is a 4100 slave that mounts behind two LED/switch modules. Each LED/switch controller handles up to 64 switches and 64 LEDs on the modules and communicates their status to the 4100ES CPU. This is sufficient for 32 zones.
Step 6. Installing LED/Switch Modules into Expansion Bays, Continued LED/Switch Controller Card, (continued) If more than 32 zones are required, a second controller (4100-1289) will be required. Note that an ME0456 fan control module counts as 8 zones when adding up the controller requirements. LED 1. This LED illuminates if communication loss between the controller and the CPU occurs. It is independent of jumper P1 (which configures different communication loss features).
Step 6. Installing LED/Switch Modules into Expansion Bays, Continued Mounting the Additional LED/ Switch Controller Card Refer to Figure 2-14 and the instructions below to mount the LED/switch controller card assembly to the back of one of the LED/switch cards. 1. Use four 322-123 nuts and four 268-009 bay washers to secure the 637-141 bracket to the inside front of the expansion bay. Note that there is only one location where the bracket can be mounted, as shown in Figure 2-13. 2.
Step 6. Installing LED/Switch Modules into Expansion Bays, Continued LED/Switch Modules All types of modules are mounted to the front of a bay, and are connected to each other via a ribbon cable. Each module operates by the same rules: when a button is pressed, the controller card sends the CPU the information, and the action programmed for that button occurs. Wiring Instructions To interconnect display cards and connect the controller card to a power source: 1.
4100ES Fan Control Module {xe "service port: software modes"}{xe "software modes"} Overview The ME0456 is a 4100ES style Switch/LED display module designed specifically for fan control. It complies with the requirements of AS 1668.1:1998. It has rotary switches and LEDs for 4 sets of fans. In order to accommodate the required rotary switches, the front plate is joggled forward so that it protrudes through the trim.
Figure 2-16.
Installing Other Modules Detailed installation instructions for these modules can be found in these instruction documents. A copy of the appropriate document is supplied in the kit with each module. Table 2-4. Module Installation Documents for 4100ES-S1 Part Code Description 4100-3101AU IDNET module provides an additional IDNET loop, with up to 250 devices. This is a PDI card. IDNET+ module provides 1, 2, 3 or 4 additional IDNET loops with independent fault isolation.
Chapter 3 Networking {xe "Network 4100 Fire Alarm System"} Introduction A basic 4100ES-S1 system becomes a network node when a Network Interface Card (NIC) or other compatible network card is installed and connected to another network node. How network cards connect to each other depends on the type of media cards being used. In this Chapter Refer to the page number listed in this table for information on a specific topic.
Network Configuration Overview Multiple 4100ES-S1 panels can be connected together into a network system by using network interface cards (NICs). When a NIC is installed into a 4100ES-S1, it is used to connect to other network nodes. Nodes may consist of other 4100ES-S1 or 4100ES panels, or they may be other types of node such as Graphic Command Centre (TSW), or Visual Command Centers (VCCs).
Network Configuration, Continued Connecting Loops Network rings or loops can be joined via physical bridge cards. There may be no more than two network loops connected in tandem. For every two loops that are interconnected (using one physical bridge), there can be a maximum of three other physical bridges used in a star configuration. See Figure 3-2.
Getting Started Overview This chapter describes how to turn a basic 4100ES-S1 into a network node. This process consists of the following: Step 1. Mounting media cards to the network interface card (NIC) Step 2. Mounting the network cards in the panel Step 3. Wiring between panels Each step is described in this chapter. Before beginning the installation, review the next few pages for a detailed description of network cards and the media cards that mount onto them.
Introduction to the 4100 Network Interface Card (NIC), Continued Network Module Illustrations Figure 3-3. 4100-6014 Network Interface Card {xe "network interface card (NIC): LEDS"} NIC Card LED Indications The 4100-6014 NIC has the following LEDs: LED1 (yellow). Illuminates when The host CPU requests it to illuminate A transmission fails It is off-line with the host CPU It needs to be configured LED2 (red). Illuminates when a data ‘0’ is received at the right port. LED3 (green).
Introduction to the 4100 Network Interface Card (NIC), Continued NIC Media Cards There are two media cards that can be plugged into the 4100-6014 NIC: 4100-6057 Fiber-Optic Media Card (565-261) 4100-6056 Wired Media Card (565-413) {xe "media cards"}{xe "fiber-optic media card"}{xe "wired media card"} Each module is shown below. FIBRE OPTIC DATA: TRANSMIT (U1), RECEIVE (U2) 40-PIN NETWORK INTERFACE CARD CONNECTOR (J1) Figure 3-4.
Introduction to the 4100 Network Interface Card (NIC), Continued {xe "wired media card: specifications"}{xe "fiber-optic media card: specifications"}{xe "network interface card: specifications"}{xe "modem media card: specifications"} Requirements and Limitations Table 3-1.
Step 1. Configuring Network Cards, Continued NIC Card Jumper Settings There are two jumper settings on the NIC card: P3 and P4. P3: Determines the NIC data transmission rate, 57.6 kbits/second or 9600 bits/second. Position 1 – 2 (the right two pins) or no pins jumpered: 57.6 kbits/second (default for 4100ES-S1). Position 2 – 3 (the left two pins): 9600 bits/second. P4: Determines the data protocol, 8-bit or 9-bit, that the NIC card is using.
Step 2. Mounting Media Cards to the NIC {xe "network interface card (NIC): mounting media cards to"}{xe "modem media card: mounting to NIC"}{xe "mounting: fiber-optic media card to NIC"}{xe "mounting: modem media card to NIC"}{xe "mounting: wired media card to NIC"}{xe "fiber-optic media card: mounting to NIC"}{xe "wired media card: mounting to NIC"} Overview The 4100-6014 Network Interface Card (NIC) uses media cards to connect to other NICs.
Step 4. Wiring Network Cards Overview The nodes in the network now have to be wired together, so that the NIC in one host panel connects to the NIC in the next panel. {xe "network interface card (NIC): wiring"}{xe "wiring: network interface card (NIC)"} Wiring Guidelines Refer to the following guidelines field wiring General Network nodes must be wired from right port to left port, regardless of the media type selected. Best protection is achieved by wiring the nodes in a loop fashion.
Step 4. Wiring Network Cards, Continued Wiring Distances Maximum wiring distances are shown in Table 3-2. Table 3-2. Wiring Distances Media Type Size Data Rate Max Distance 0.2 mm2 unscreened twisted pair 57.6 kbps 2,100m 9.6 kbps 3,600m 57.6 kbps 3,000m 9.6 kbps 5,200m Wired 2 0.8 mm screened twisted pair 50/125 um 3,000m (4dB/km loss) 57.6 or 9.6 kbps 50/125 um 4,500m (3dB/km loss) Optical Fibre 62.5/125 um 4,000m (4dB/km loss) 57.6 or 9.6 kbps 62.5/125 um (3.
Step 4. Wiring Network Cards, Continued Fibre-Optic Wiring Connectors U1 (transmitter) and U2 (receiver) on the 4100-6057 Fiber-Optic Media Card are used to connect 4100-6014 NICs across parts of a network. {xe "network interface card (NIC): wiring, fiber-optic"}{xe "wiring: fiber-optic media card"}{xe "fiber-optic media card: wiring"} Note: ST connectors with long strain relief boots must be used with the fibre optic cable. Fibre Optic Connection Types Dual Fibre Optic Cable Connections.
Step 4. Wiring Network Cards, Continued 4190-9010 Coupler Requirements The 4190-9010 Coupler is used with the 4100-6057 Fibre Optic Media Board, revision “C” or higher. Two 4190-9010 Bi-Directional Couplers are required per connection, one at each node. {xe "fiber-optic media card: wire distances"}{xe "fiber-optic media card: coupler requirements"} The 4190-9010 is equipped with type ST connectors. To make type ST to type ST connections, an ST to ST coupler, by others, is required.
Step 4. Wiring Network Cards, Continued 4190-9010 Coupler Requirements (continued) The illustration below shows coupler wiring.{xe "fiber-optic media card: coupler requirements"}{xe "wiring: coupler for fiber-optic media"} Figure 3-7. Coupler Wiring Wiring with the Wired Media Card Refer to the guidelines and figures in this topic to use wired media cards.
3-15
Step 4. Wiring Network Cards, Continued Wiring with the Wired Media Card (continued) Figure 3-8 shows how to connect between two CPU motherboards with wired media network cards. The right port terminals (TB3) on one 4100ES-S1 are connected to the left port terminals (TB1) of the other 4100ES-S1. Table 3-5 details the screw terminals on the CPU motherboard. R+ R- 18 AWG 1 TB3 10 Right Port Left Port TB1 8 L+ 1 L- Figure 3-8.
Step 4. Wiring Network Cards, Continued {xe "wiring: fiber-optic media card"}{xe "fiber-optic media card: wiring"}Figure 3-9 shows an example of loop network cabling using a mixture of fibre optical cable and twisted pair. Note that the left port of any network card is connected to the right port of the next network card regardless of whether the connection is fibre or copper.
Chapter 4 The System Power Supply & Alarm Relay Card Introduction The system power supply (SPS) is described in Chapter 2. A picture of it is shown in Figure 2-4. This chapter has the current and voltage ratings of the SPS and describes how it is installed and configured by the factory. It also describes the Alarm Relay Card that mounts onto the SPS to provide three extra relays. Field wiring of the SPS is covered in Section 5.
SPS Specifications Input/Output/Battery Specifications Table 4-1 summarizes the specifications for the SPS.{xe "system power supply (SPS): specifications"} Table 4-1. SPS Input and Output Specifications AC Input Specifications SPS in Basic 4100ESS1 (4100-9848AU) 240 VAC + 6% -10% @ 50 Hz 2 A Maximum DC Output Specifications Nominal 28VDC Minimum: 19.5 VDC Maximum: 32 VDC Ripple: 2 VDC p-p @ full load (9A) Voltage 9A alarm load. Includes: NACs; +24V Card; +24V Aux; SPS card including on-board IDNet.
SPS Specifications, Continued SPS Current Consumption The bulk supply (rated at 9A max) which feeds 24V Sig, 24V Card, 24V Aux also supplies the SPS Card including the on board IDNet, and the battery charger. The charger is disabled during alarms so as to make the 9A available on the other busses. (See Table 4-2 for the SPS current). +24V Sig is used to supply the NACs. It can be made accessible for other use by configuring a NAC as an auxiliary power output (normally energized).
SPS Adjustments {xe "system power supply (SPS): configuring "}{xe "remote power supply (RPS): configuring "}{xe "card configuration: system power supply (SPS)"}{xe "card configuration: remote power supply (RPS)"} Adjusting Voltages There are two 4mm (i.e. small) potentiometers on the 4100-9848AU SPS, situated below the centre of the PCB. These are adjusted in the factory and typically will not need adjusting in the field.
SPS LED Indications Status LEDs The SPS has the following LEDs: {xe "system power supply (SPS): LEDs"}{xe "remote power supply (RPS): LEDs"} LED1 (yellow). Illuminates when NAC 1 is ON or in Fault. LED2 (yellow). Illuminates when NAC 2 is ON or in Fault. LED3 (yellow). Illuminates when NAC 3 is ON or in Fault. LED4 (yellow). Illuminates to indicate a communications loss with the system CPU; normally off. LED5 (yellow). Indicates IDNet status. Normally off. Slow blink: Class A open circuit Fault.
Troubleshooting an SPS {xe "system power supply (SPS): troubleshooting"}{xe "remote power supply (RPS): troubleshooting"}{xe "troubleshooting: SPS"}{xe "troubleshooting: RPS"} Overview This section contains explanations of fault messages associated with the SPS that may appear on the 4100ES-S1 display. Heading text in the left margin shows the error message, while the paragraph next to it describes the likely cause of the message.
The Alarm Relay Card {xe "system power supply (SPS): troubleshooting"}{xe "remote power supply (RPS): troubleshooting"}{xe "troubleshooting: SPS"}{xe "troubleshooting: RPS"} Overview The Alarm Relay Card mounts on, and is driven by, the SPS. It has 3 relays, each providing one set of voltage-free contacts. It is fitted to the basic 4100ES-S1 as standard. The relays are able to be configured under custom control, but the default operation is for system status, i.e.
The Alarm Relay Card, Continued Configuration The relays have one set of voltage-free contacts (see note below) connected to one pair of terminals via a header. The two terminals are configured for normally closed or normally open by positioning a jumper on the relay card. Refer to Table 4-3. Table 4-3.
Brigade Interfaces {xe "service port: software modes"}{xe "software modes"} Overview The Alarm Relay Card is typically used to provide a Brigade Interface. The def{xe "service port: software modes"}{xe "software modes"}ault configuration is for the three relays to operate on Fault (Trouble), Isolate (Supervisory) and Alarm, respectively.
Brigade Interfaces, Continued General Wiring The ASE or AIU/PPU should be powered from the fused DC distribution board on the power supply. It is recommended that the brigade device does not share its fuse protection with any other equipment, for reliability. The wiring between the brigade device and the 4100ES-S1 should be routed neatly as shown in the following drawings, and secured in place with the cable ties and adhesive tie holders supplied with the kits.
Chapter 5 SPS Field Wiring (4100ES-S1) Introduction This chapter shows how various devices are wired to an SPS. It includes connection to NACs, IDNet, relays, and power circuits. In this Chapter Refer to the page number listed in this table for information on a specific topic.
General Field Wiring Guidelines General Guidelines All field wires must be 0.75 mm2 or greater cross section and comply with AS 1670.1 and the wiring code. Conductors must test free of all earth leakage. All wiring must be done using copper conductors only, unless noted otherwise. If shielded wire is used, - the metallic continuity of the shield must be maintained throughout the entire cable length.
SPS NAC Field Wiring Guidelines {xe "wiring: distances, Class A (NAC)"}{xe "NACs: wiring distances (Class A)"}{xe "Class A wiring: distances (NAC)"} Overview Each of the three NACs on the SPS has two pairs of driven outputs (A+/A-, B+/B-) which operate together. NAC B outputs have polarity reversal supervision and expect a 10k EOLR. Each connected device must have a suitably rated blocking diode. EOLRs are supplied fitted to the NAC terminals.
SPS NAC Field Wiring Guidelines, Continued Some or all of these output functions could be implemented using addressable devices or other relay modules instead, in which case the corresponding NAC output could be reassigned to other uses. The new configuration would require full testing of these functions to ensure compliance with AS 4428.1.
SPS NAC Field Wiring Guidelines, Continued {xe "wiring: Class B (NAC)"}{xe "Class B wiring: NACs"}{xe "NACs: wiring (Class B)"} Class B (string) NAC Wiring To connect the SPS to appliances using Class B wiring, read the following instructions and refer to the figure below. 1. Route wire from the B+, B- outputs on TB2 of the SPS to the appropriate inputs on a peripheral notification appliance. Use NAC1, NAC2, or NAC3, as required. 2. Route wire from the first appliance to the next one.
Power Supply Wiring Distances {xe "wiring: distances, Class A (NAC)"}{xe "NACs: wiring distances (Class A)"}{xe "Class A wiring: distances (NAC)"} Overview Before wiring from any type of power supply to notification appliances, check Tables 5-1 and 5-2 for wiring distances. Class A NAC Wiring Table Table 5-1 lists the maximum distances from the NAC terminal block to the last appliance in a Class A (loop) configuration, depending on wire gauge and current.
Power Supply Wiring Distances, Continued {xe "wiring: distances, Class B (NAC)"}{xe "NACs: wiring distances (Class B)"}{xe "Class B wiring: distances (NAC)"} Class B NAC Wiring Table Table 5-2 lists the maximum distances from the NAC terminal block to the last appliance in a Class B (string) configuration, depending on wire gauge and current. Use Table 5-2 to calculate wire distances for your application if you are using Class B wiring. Table 5-2. Class B (string) Wiring Distances Alarm Current @ 24V 0.
Using T-GEN 50 with 4100ES-S1 Overview AS 1670.1 requires fire alarm warning systems to produce sounds complying with ISO 8201. One way of meeting this requirement in a 4100ES system is to use a TGEN 50 tone generator, which is capable of driving up to 50W of load on a 100V speaker line. The recommended version of the T-GEN 50 for use in 4100ES-S1 is available as part 4100-0766K (see PID information in Chapter 1).
Using T-GEN 50 with 4100ES-S1, Continued B+ SHLD AA+ IDnet B+ B-A+ A- B+ B-A+ A- B+ B-A+ ANAC1 NAC2 NAC3 4100U SPS (4100-9848AU) To T-GEN 50 4N 2I V - + - + F2 + - + F3 + - + F4 + - + - F1 Figure 5-4. Taking Ancillary Power from NAC1 To make this work, NAC1 must be programmed as AUXPWR to make it turn on continuously without supervision. The NAC output capacity is 2A overall.
Using T-GEN 50 with 4100ES-S1, Continued Controlling a T-GEN 50 with a Relay Module T-GEN 50 FAULT RELAY OUTPUT FB FB COM NO 4100-3003 Relay Module NO NC COM DEF- 10 k ohm resistor SIG A/I/EALM0V +24V +24V To AUX POWER DC INPUT 0V Auto 150 (1.0 mm2) or heavier EARTH LINE - Mains rated cable for 100V speaker wiring LINE + Connector block mounted on bracket Figure 5-5. Relay Module Connection to a T-GEN 50 A T-GEN 50 can be operated and supervised using a 4100-3003 or 4100-3204 relay module.
Using T-GEN 50 with 4100ES-S1, Continued T-GEN 50 Setting for Relay Operation Table 5-3 shows the switch and link settings for T-GEN 50 software version 1.7 when controlled from a relay output. Table 5-3. T-GEN 50 Settings Alert to Evacuate Change-Over Time SW1 SW2 (T1) SW3 (T0) (T2) OFF OFF OFF ON OFF OFF OFF ON OFF ON ON OFF OFF OFF ON ON OFF ON OFF ON ON ON ON ON Setting on T-GEN 50 0 sec 30 sec 1 min 1.
Using T-GEN 50 with 4100ES-S1, Continued A T-GEN 50 can be controlled and supervised using a NAC output. The NAC is used to control the ALM- input to the T-GEN 50 and to supervise its Fault relay output. The T-GEN 50 is configured to supervise the 100V wiring to the loudspeakers. Figure 5-6 shows the wiring between the T-GEN 50 and the NAC terminals.
Using T-GEN 50 with 4100ES-S1, Continued T-GEN 50 Settings for NAC Operation Table 5-4 shows the switch and link settings for T-GEN 50 software version 1.7 when controlling from a NAC output. Table 5-4. T-GEN 50 Settings Alert to Evacuate Change-Over Time SW1 SW2 (T1) SW3 (T0) (T2) OFF OFF OFF ON OFF OFF OFF ON OFF ON ON OFF OFF OFF ON ON OFF ON OFF ON ON ON ON ON Setting on T-GEN 50 0 sec 30 sec 1 min 1.5 min 3 min 5 min 10 min Alert Only SW1 to SW3 settings have no effect on Slave T-GEN 50s.
Using T-GEN 50 with 4100ES-S1, Continued Fitting an Evacuation Control An optional three-position control ME0460 (see part numbers in Chapter 1) allows the TGEN 50 to be switched from the front panel between automatic operation, being Isolated, or producing Evacuation tone, regardless of the state of other control inputs. With the control in the ISOLATE position, the T-GEN 50 will not respond to the ALMinput, nor activate its FAULT output if a fault is present.
Using T-GEN 50 with 4100ES-S1, Continued 100V Speaker Wiring Refer to the T-GEN 50 Installation and Operating Guide (LT0186) for details about the wiring of speakers and end-of-line resistor requirements for the T-GEN 50. ME0460 Evac Control fitted to blank display module ME0490 lead routed inside cabinet to T-GEN 50 ME0490 PA Microphone fitted to 4U Brigade Door ME0460 Evac Control fitted to 4U Brigade Door Figure 5-8.
SPS Auxiliary Power Wiring Overview The panel, battery-backed, unregulated dc bulk power is available from the SPS via the NAC and the 24V Aux power terminals. NACs can be configured as auxiliary power point type in the 4100ES Programmer. All of these are power-limited. Guidelines Review the following guidelines before using the SPS for auxiliary power.
SPS Auxiliary Power Wiring, Continued {xe "auxiliary power: isolators and"}{xe "IDNet power isolator"}{xe "isolators"}{xe "power isolators"} Wiring The SPS can connect to auxiliary power appliances via the dedicated auxiliary power tap (TB3). See Figure 5-9. If more power is needed, any of the three NAC outputs can be used for auxiliary power. AUXILIARY POWER 2 AUXILIARY POWER AUXILIARY POWER Ferrite bead required for EMC compliance. Use SX0005 or kit 4100-5129. 2 0.
SPS Relay Wiring {xe "wiring: SPS auxiliary relay"}{xe "system power supply (SPS): wiring, auxiliary relay"}{xe "wiring: auxiliary relay"}{xe "auxiliary relay"} Overview The SPS has one programmable relay, Aux 1, with one set of voltage-free contacts (see below). The Alarm Relay 4100-6033 is fitted as standard to 4100ES-S1. This has 3 relays, each with one set of normally open (or normally closed) contacts available on a screw terminal block (see Chapter 4).
SPS IDNet Wiring {xe "guidelines for wiring: IDNet"}{xe "IDNet: guidelines for wiring"}{xe "wiring: guidelines (IDNet)"}{xe "remote power supply (RPS): wiring guidelines (IDNet)"}{xe "system power supply (SPS): wiring guidelines (IDNet)"} Overview This section describes how the IDNet Channel on the SPS connects to addressable devices/detectors. The guidelines governing IDNet wiring guidelines are covered in Chapter 6, IDNet Installation.
SPS IDNet Wiring , Continued 1. The current allowance per device on the loop is 0.5mA with the LED off, 2mA with the LED on. A maximum of 20 LEDs will be turned on at any time by the IDNet Card, e.g. in alarm. 2. The minimum voltage allowed at the furthest device to guarantee operation is 24.9Vdc. The IDNet boosts its output voltage from 30V to 35V during alarm. 4500 4500 4.0 sq.mm Maximum Cable Distance (metres) Notes 4000 4000 3500 3500 3000 3000 2.5 sq.mm 2500 2500 2000 2000 1.5 sq.
SPS IDNet Wiring , Continued Class A (loop) Wiring To connect addressable devices/detectors to the SPS IDNet using Class A wiring, read the following instructions. 1. 2. Ferrite beads are required on the SPS IDNet cables (refer Figure 5.1). Route wire from the B+, B- outputs on TB1 of the SPS to the appropriate inputs on a peripheral IDNet device. 3. Route wire from the first IDNet device to the next one. Repeat for each device. 4.
SPS IDNet Wiring , Continued {xe "wiring: Class B (IDNet)"}{xe "Class B wiring: IDNet"}{xe "IDNet: wiring (Class B)"}{xe "remote power supply (RPS): wiring (IDNet Class B)"}{xe "system power supply (SPS): wiring (IDNet Class B)"} Class B (string) Wiring To connect addressable devices/detectors to the SPS IDNet using Class B wiring, read the following instructions. 1. 2. 3. Under AS 1670.1 Class B wiring is allowed only for a maximum of 40 addressable devices.
Chapter 6 Using Install Mode Introduction Install Mode is a 4100ES facility which is useful during panel installation. While a 4100ES panel is being installed and commissioned, there will often be periods when many internal modules or external devices are not yet connected, or are not in a normal state for some reason. With the full configuration loaded in the 4100ES, each missing or off-normal device gives rise to a fault.
Adding Devices to Install Mode Adding a Single Device to Install Mode Devices can be added individually to the Install Mode list. NOTE: this requires being logged in at Level 3. Refer to the Operator Manual, if necessary, to do this. 1. 2. 3. 4. Press the key and step through the list with the Next/Previous arrows to find the device. Press the key. Step through the list of options with the Next/Previous arrows to find the Add to Install Mode? option. Press to select this.
Viewing and Removing Devices in Install Mode Viewing Contents of Install Mode list To view the devices and other contents currently in Install Mode: 1. 2. 3. 4. 5. Removing Individual Devices from Install Mode Press the
6-4
Chapter 7 PC Software Connections {xe "service port"} Introduction The service port on the door with the Operator Interface enables the 4100ES-S1 to connect to a PC running important utilities, such as diagnostics, programming, CPU firmware downloading, and channel monitoring. In this Chapter Refer to the page number listed in this table for information on a specific topic.
Software Modes {xe "service port: software modes"}{xe "software modes"} Overview The 4100ES-S1 can connect to a PC running important utilities, such as diagnostics, programming, CPU firmware downloading, and channel monitoring. It connects to the PC running all of these utilities via the service port on the CPU card.
Software Modes, Continued Software Modes (continued) Master Bootloader Interface Mode. This mode is used to download the Master CPU Exec firmware and the CFG.TXT file to the CPU via the serial port or through the Ethernet port. download cable Laptop/PC running Programming file transfer 4100ES-S1 Panel running Bootloader Figure 7-3.
Ethernet Service Port and Serial Service Port Ethernet Service Port Overview (0566-719 only) The Ethernet service port J1 on the CPU card (0566-719) is used to connect the panel to a local PC. See Figure 7-4 for the port location. Figure 7-4. CPU card ports The Ethernet service port connects to the front panel Ethernet connection through a standard straight (non-crossover) Ethernet Patch Cable.
Chapter 8 Installation Checklist, Commissioning & Maintenance {xe "service port"} Introduction The 4100ES-S1 is tested in the factory and is loaded with a basic configuration. When the panel arrives on site the installer must unpack and check the panel, mount the cabinet, any additional cards, and check the configuration before applying power. A registered electrician must connect the mains. The panel should then be powered up and checked for correct operation.
Alignment & Adjustment Overview All the 4100ES-S1 cards and modules in the base panel are tested and aligned in the factory before being supplied to the customer. The only field adjustment that may be necessary is to set the battery charger voltage. (Note this has been set and should not need re-adjusting). R341 Battery Charger Voltage Should the battery charger voltage need adjusting, the method is as follows: 1.
Power Up & Placing into Operation To place the 4100ES-S1 into operation, perform the following steps: STEP 1 Ensure that the Mains Switch is OFF. STEP 2 Ensure that 240 VAC is connected to the panel from the mains distribution switchboard. STEP 3 Ensure that the Lithium battery is fitted to battery holder on the CPU card, and link P3 is fitted to the BAT ON position. Turn the Mains Switch ON. STEP 4 Check that the green "MAINS ON" LED indicator is on.
Maintenance The 4100ES-S1 system must be kept free from faults and tested on a weekly, monthly and annual basis to verify that it is operating correctly. The tests required by part 8 of the standard AS 1851 Maintenance of Fire Protection Equipment are detailed in the 4100ESS1 Operator Manual, LT0395. The Operator manual also provides detail of report printing and performing tests that are useful for checking the system.
Appendix A Card Address DIP Switch {xe "addresses: setting, for 4100U modules"}{xe "card configuration: address setting"} Overview Addressable cards include a bank of eight DIP switches. From left to right (see Figure A1, below) these switches are designated as SWx-1 through SWx-8. The function of these switches is as follows: SWx-1. This switch sets the data rate for the internal 4100ES communications line running between the card and the CPU. Set this switch to ON. SWx-2 through SWx-8.
Overview, (continued) Table A-1.
Appendix B Programming Requirements {xe "ULC programming requirements"} Introduction This appendix briefly summarises the programming that is required to comply with AS 4428.1. It does not provide equations or detail of programming. Refer to LT0400 4100ES-S1 Programming Guide for descriptions of the AS 4428.1 programming. The separate 4100ES Programming Manual tells how to use the PC-based 4100ES Programmer.
B-2
Appendix C Checking System Wiring {xe "wiring: troubleshooting"}{xe "troubleshooting: wiring"}{xe "volt-Ohm meter usage"} Overview This appendix contains instructions on how to use a volt/ohm meter to check system wiring. Using the Volt/ Ohm Meter When using the volt/ohm meter to check each circuit, make sure to adhere to the notes and instructions below. Notes: For these tests, the mains connection to the panel must be in place, but the mains must be switched off and the battery must be disconnected.
Continued on next page Appendix C: Checking System Wiring, Continued Meter Readings Table C-1 lists the correct meter readings for different circuit types. Remember, these readings must be made with the field wiring disconnected from the 4100ES terminals. Table C-1. Acceptable Zone and Signal Circuit Meter Readings Circuit Type Meter Reading Class B (spur) Detector Circuit (each circuit) From zone + wire to zone – wire (each zone) 3.
Appendix D Earth Fault Detection {xe "wiring: Earth Fault Search"}{xe "Earth Fault Search"} Overview This appendix contains instructions on how to use the Earth Fault Search feature of the 4100ES-S1 diagnostics menus. Earth Fault Search is a diagnostic search of external field wiring that assists in locating circuits with earth faults. An earth fault occurs when an electrical circuit is shorted to ground.
General Guidelines Review the guidelines below before initiating an Earth Fault Search. The Detect Earth Fault jumper must be installed at the SPS for earth fault detection to occur. Only one power supply per location is configured to detect earth faults. For more reliable earth fault searching: - Use IDNet channel isolators to isolate channel faults to a specific segment of channel wiring.
Earth Fault Searching from the Front Panel Overview This section describes how to conduct an Earth Fault Search, from selecting the appropriate access code to correcting the fault. Access Level Selection The panel must be at the appropriate access level (1, 2, 3, or 4) in order to run diagnostics. To get to the correct access level: 1. Press the Menu button. The following message comes up (press the Next or Previous buttons, if necessary, to display it).
Earth Fault Searching from the Front Panel, Continued Starting the Earth Fault Search, Continued 6. Press the Enter button. The following options become available when you press the Next and Previous buttons: Press or to scroll Location Search Press or to scroll IDNet Channel Search Press or to scroll Last Search Result The search types are described below.
Earth Fault Searching from the Front Panel, Continued Search Option B: Select Channel If you select the IDNet Channel Search menu item, a list of IDNet channels to search becomes available. Use the Next and Previous buttons to scroll through the list. When the IDNet channel you want to search is shown and "Press to start search" displays, the search is ready to start. A sample screen is shown below.
Search Results Overview There are several types of results that can display at the end of an Earth Fault Search. This section covers all types of results. IMPORTANT: Once you have been directed to an earth fault and corrected it, it is recommended that you restart the system (warm- or cold-start). Non-Point Faults A non-point fault indicates a ground that cannot be traced to an addressable point (for example, a shield or an audio riser).
Search Results, Continued Point Faults, Continued IDNet isolator fault. The message below shows a fault detected after the IDNet isolator was turned on: CARD 2, IDNET CARD (250 POINTS) M1-3, IDNET ISOLATOR EARTH FAULT Fault Not Found If the message in the lower right corner of the LCD reads FAULT NOT FOUND (for a Location Earth Fault Search) or FAULT CLEAR FAIL (for an IDNet Channel Earth Fault Search), it means the search could not locate the fault, but it acknowledges that a fault exists.
D-8
Appendix E Related Documentation {xe "documentation set"} The following manuals are relevant to the 4100ES-S1.
Appendix E: Related Documentation, Continued Book Part Number (cont.) Title (cont.
Appendix F Compatible Actuating Devices Introduction This appendix describes the following: In this Chapter Devices that have been approved as compatible devices for use with the 4100ES-S1. Devices approved for use with the IDNet and shows the number allowed per loop. Refer to the page number listed in this table for information on a specific topic.
List of Approved Devices, Continued System Sensor Range - Conventional Detectors Detector Type 4100-5001/2/4 2190-9156 8 Zone Module Monitor ZAM 885WP-B Weatherproof Heat 40 40 Detector Type B * * 4090-9101 Monitor ZAM 40 Remote indicator output cannot be wired in common with Tyco 614 series or the Minerva M614 series (and most other Tyco/Olsen) detectors.
List of Approved Devices, Continued Apollo Range - Conventional Detectors Series 60 Heat detector Type A Series 60 Heat detector Type B Series 60 Heat detector Type C Series 60 Heat detector Type D Series 60 55000-310 Aus Photoelectric smoke detector Series 60 55000-240 Aus Ionisation smoke detector Brooks Range - Conventional Detectors PFS-A PFS-B PFS-C PFS-D PFS-P PFS-P MK II PFS-I PFS-I MK II Heat detector Type A Heat detector Type B Heat detector Type C Heat detector Type D Photoelectric smoke detecto
Compatible Detectors, IDNET The following lists the detectors approved for use with IDNet and shows current rating and numbers allowed per loop. Device Type Operating Current mA Maximum Number Allowed Per Loop 4098-9714E Analogue Photoelectric Smoke Detector 4098-9717E Analogue Ionisation Smoke Detector 4098-9733E Analogue Heat Type A & B Detector 4098-9754E Analogue Multi (Heat/Photo) Detector 0.5 (2 with LED on) 0.5 (2 with LED on) 0.5 (2 with LED on) 0.
Compatible Addressable Field Devices, IDNet The following lists the addressable devices approved for use with IDNet and shows current rating and numbers allowed per loop. Maximum Addressable Point On Analogue Loop 250 Maximum Addressable Points on Analogue Line 40* 250 40* 250 40* 0.5 (2 with LED on) 250 40* 0.5 250 40* 0.65 (2.8 with LED on) 0.5 (2 with LED on) 0.65 (2.8 with LED on) 0.65 (2.
F-6
Appendix G 4100ES-S1 Specifications General System Capacity Cabinet Size Cabinet Material Cabinet Finish Cabinet Colour Mounting 500 points of addressable devices, plus 500 points of annunciation. up to 4 x 4100 legacy cards up to 4 x 4” x 5” PDI cards 1050H x 550W x 280D (mm) 1.
Voltage & Current Ratings of Modules & Assemblies The DC input voltage range of the following modules is 18-33Vdc. The current listed is nominal for 24Vdc, and may be used for battery capacity calculations.
Appendix H Power Supply & Battery Capacity Calculations Power Supply Part of the system design includes calculating that the quiescent load and the alarm load are each less than the rating of the power supply. Note that the quiescent load includes devices such as door holders that are normally energized, but get switched off during alarm. The SPS rating is included in the specifications in Chapter 6.
Module FP0934 4100-1288 4100-1289 4100-3101 4100-0113 4100-0154 4100-3003 4100-3024 4100-4321 4100-5004 4100-6014 4100-6056 4100-6057 4100-0160 4100-0766 4100-0895 4100-2895 2190-9156 2190-9162 2190-9164 4090-9101 40909117AU 40909120AU 4090-9050 4098-9794E 4907-0012 Description 4100ES-S1 Basic Panel 64/64 LED Switch Controller (1st controller per bay) 64/64 LED Switch Controller (2nd controller per bay) IDNET module with 250 addressable devices RS232 Modem Interface VESDA HLI 8XSPDT,3A,24VDC Relay module 2
Appendix I List of Drawings The following drawings are included since they are referred to in this manual or are relevant. 1922-96 1976-176 1976-174 1976-181 WA ASE and Cube ASE to Fire Panel Wiring Details 4100ES-S1 Presentation Drawing 4100ES-S1 Brigade Door Assembly, Sheet 1 ASE, Sheet 3 PPU/AIU/Cube ASE 4100ES Australian Wiring Diagrams (collected in LT0432) ©2004 Tyco Safety Products Westminster, Westminster, MA 01441-001 USA.
² ² ² ² tyco Safety Products TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
² ² ² ² tyco Safety Products TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
L R L2 L2 tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products (2190-9173) WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U IDNET RELAY IAM (4090-9002) WIRING DIAGRAM Safety Products TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco Safety Products TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U 24 POINT I/O CARD (002-124) WIRING DIAGRAM Safety Products TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco 4100U Safety Products WIRING DIAGRAM TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
tyco Safety Products TYCO SAFETY PRODUCTS 17 MARY MULLER DRIVE P.O. BOX 19545 CHRISTCHURCH, PH: +64 3 3895096 NEW ZEALAND.
©2004 Tyco Safety Products Westminster, Westminster, MA 01441-001 USA. Specifications and other information shown were current as of publication, and are subject to change without notice.
