SIMP HOME I ® I L I F E B Y D E S I GN CONNAUGHT / HAMPSHIRE / SOMERSET ENTRYWAY STORAGE CABINET MODEL # AXCCON47-LGB 1/20
SIMP HOME I I ® L I F E B Y D E S I GN Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am – 4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION MODEL # AXCCON47-LGB PARTS DESCRIPTION A BL BR Fro nt / Ava nt Fro nt / Ava nt nt Ava nt / Fro TOP QTY 1 C LEFT SIDE QTY 1 D RIGHT SIDE QTY 1 E Fro nt / Ava nt Fro nt / Ava nt Fro nt / Ava nt Fro nt / Ava nt SMALL DIVIDER QTY 1 LARGE DIVIDER QTY 1 F G MIDDLE FRAME QTY 1 H Fro nt / Ava nt BOTTOM SHELF QTY 1 CABINET SHELF QTY 2 DOOR (L&R Same) QTY 2 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120
PRE-ASSEMBLY INFORMATION MODEL # AXCCON47-LGB PARTS DESCRIPTION IL IR LEFT BACK QTY 1 KL Warning Label DRAWER FRONT QTY 2 RIGHT BACK QTY 1 L KR LEFT DRAWER SIDE QTY 2 J RIGHT DRAWER SIDE QTY 2 DRAWER BACK QTY 2 M DRAWER BOTTOM QTY 2 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION MODEL # AXCCON47-LGB HARDWARE DESCRIPTION 1 2 ALLEN KEY SCREW M6 X 30 mm QTY 26 5 WOOD DOWEL Ø8 X 30 mm QTY 16 CAM LOCK PIN CAM LOCK QTY 16 SETS 6 7 PHILLIPS SCREW ROUND HEAD M4 X 15 mm QTY 21 9 4 3 SHELF SUPPORT QTY 12 10 ALLEN KEY QTY 1 8 PHILLIPS SHORT SCREW PHILLIPS MEDIUM SCREW M3 X 12 mm M3 X 15 mm QTY 12 QTY 8 11 12 a. b. c.
COMPONENTS – KEY DIAGRAM MODEL # AXCCON47-LGB Fron t/A van t IR Fron t/A van t Fron t/A van t IL Fron t / Av ant BL BR H H Fron t/A van t Fron t/A van t Fron t/A van t KR KL 8/20
ASSEMBLY MODEL # AXCCON47-LGB STEP 1 KR KL J 2 1. Attach 4 Cam Lock Pins 2 to back of Drawer Front J . 2. Align Cam Lock Pins with guide holes and attach Drawer Sides KL , KR . 3. Insert 2 Cam Locks 2 into guide holes on each Drawer Side KL , KR . 4. Use flathead screwdriver secure Cam Locks. STEP 2 M KR J KL 1. Slide Drawer Bottom M firmly into slots on Drawer Sides KL , KR and Drawer Front J .
ASSEMBLY MODEL # AXCCON47-LGB STEP 3 L KR 1 4 M KL 1. Align Drawer Back L with Drawer Bottom M and press firmly into slot . 2. Attach back using 2 Allen Key Screws 1 through guide holes on each Side KL , KR . 3. Use Allen Key 4 to tighten screws. Do not over-tighten. STEP 4 NOTE: The screwdriver is not included in the hardware pack. J 9 1. Use Phillips Screwdriver to attach Handle 9 to Drawer Front J . Repeat Step 1-4 for the second drawer.
ASSEMBLY MODEL # AXCCON47-LGB Front / Avant Front / Avant STEP 5 Front / Avant Front / Avant 1 4 1. Attach Small Divider D to Middle Frame E using 2 Allen Key Screws 1 . 2. Use Allen Key 4 to tighten screws. Do not over-tighten. STEP 6 Front / Avant Front / Avant Front / Avant Front / Avant 3 2 1. Insert 2 Dowels 3 into guide holes on Large Divider C . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3.
ASSEMBLY MODEL # AXCCON47-LGB Front / Avant STEP 7 Front / Avant 1 3 Front / Avant Front / Avant Front / Avant 4 1. Insert 2 Dowels 3 into guide holes on Large Divider C . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3. Attach Large Divider C to Bottom Shelf F using 3 Allen Key Screws 1 through guide holes. 4. Use Allen Key 4 to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCCON47-LGB STEP 8 1 3 BR BL Front / Avant Front / Avant Front / Avant Front / Avant 4 3 2 1. Insert 4 Dowels 3 into guide holes on each Side BL , BR . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3. Attach 3 Cam Lock Pins 2 to each Side BL , BR into pre-drilled holes. 4. Align and insert Cam Lock Pins on Sides BL , BR into guide holes on Bottom Shelf F . 5. Place 6 Cam Locks 2 into guide holes on Bottom Shelf F . 6.
ASSEMBLY MODEL # AXCCON47-LGB 3 STEP 9 1 Front / Avant 4 Front / Avant Front / Avant Front / Avant Front / Avant BL BR 1 4 1. Insert 2 Dowels 3 into top corners of each Side BL , BR . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3. Align guide holes bottom corners of Top A with Dowels 3 in Sides BL , BR . 4. Attach Top A to Sides BL , BR and Small Divider D using 9 Allen Key Screws 1 . 5. Use Allen Key 4 to tighten screws.
ASSEMBLY STEP 11 MODEL # AXCCON47-LGB Last Step ( after adjust the door ) First Step 7 7 7 11 H BR BL H 8 8 10 1. Attach hinges on Doors H to Sides BL , BR using Phillips Screws 7 into pre-drill holes: - Using Phillips screwdriver to attach Screws 7 at middle hole of hinges for both top & bottom hinges. - Adjust the door to ensure they are aligned straight & square with bottom shelf & side.
ASSEMBLY MODEL # AXCCON47-LGB STEP 12 shelf level 1 shelf support anti - tipping shelf level 2 6 shelf level 3 6 1. Use 4 Shelf Supports 6 for each Shelf Cabinet G in desired location. 2. 2 Shelf Supports 6 may be used on back top of each Shelf Cabinets G as a tipping restraint.
ASSEMBLY MODEL # AXCCON47-LGB STEP 13 1. Insert assembled drawers into drawer glides on assembled cabinet.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP 14 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. Drill a 3/16 inch hole in the wall.
SIMP HOME I I ® L I F E B Y D E S I GN WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.