TM SIMP HOME ® LIFE BY DESIG N TM LOWRY / MITCHELL / FULTON SIDEBOARD BUFFET MODEL # AXCLRY-10GW 1/29
TM SIMP HOME ® LIFE BY DESIG N TM Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am –4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Keep this manual for future reference. CARE and MAINTENANCE Wood Furniture Care Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION . PART DESCRIPTION A MODEL # AXCLRY-10GW . . B CL vant t/A Fron Fron t/A vant Fron t/A TOP QTY 1 . van t LEFT SIDE QTY 1 BOTTOM SHELF QTY 1 . CR . DL Fron DR t/A vant Fron t/A RIGHT SIDE QTY 1 . t LEFT DIVIDER QTY 1 . E RIGHT DIVIDER QTY 1 . FL MIDDLE FRAME QTY 2 . FR LEFT DOOR QTY 1 . G RIGHT DOOR QTY 1 .
PRE-ASSEMBLY INFORMATION . PART DESCRIPTION J . . K JOINING STRIP QTY 1 . LL DRAWER FRONT QTY 3 . LR LEFT DRAWER SIDE QTY 3 . M RIGHT DRAWER SIDE QTY 3 MODEL # AXCLRY-10GW N DRAWER BACK QTY 3 DRAWER BOTTOM QTY 3 . O LEG QTY 2 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION . HARDWARE DESCRIPTION 1 2 . . . 5 3 . . 9 . . 8 MAGNET AND PLATE QTY 2 SETS . 10 PHILLIPS SCREW M3 X 15mm QTY 8 ALLEN KEY SCREW M6 X 30mm QTY 48 7 PHILLIPS SCREW ROUND HEAD M4 X 15mm QTY 28 ALLEN KEY QTY 1 4 WASHER Ø19 / Ø8 x 1 mm QTY 12 6 . . LOCK WASHER Ø12 / Ø8 x 1.5 mm QTY 12 ALLEN KEY BOLT M8 x 20 mm QTY 12 . MODEL # AXCLRY-10GW .
COMPONENTS-KEY DIAGRAM MODEL # AXCLRY-10GW A Fron t/A van t H J CR DR DL CL Fron t / Av Fron t / Av G ant Front FL I ant G Fron t / Av ant FR / Ava nt Fron t/A van t B E O O M LR N LL K 8/29
ASSEMBLY MODEL # AXCLRY-10GW STEP-1 P X 14 K 14 K 1. Attach four Cam Lock Pins 14 to pre-drilled holes at back of Drawer Front K . 2. Use Phillips screwdriver secure Cam Lock Pins.
ASSEMBLY MODEL # AXCLRY-10GW STEP-2 LR LL K 14 K LR LL 14 1. Align Cam Lock Pins with drilled holes and attach Drawer Sides LL , LR . 2. Insert two Cam Locks 14 into drilled holes on each Drawer Side LL , LR . 3. Use Phillips screwdriver secure Cam Locks.
ASSEMBLY MODEL # AXCLRY-10GW STEP-3 N LR K LL 1. Slide Drawer Bottom N firmly into slots on Drawer Sides LL , LR and Drawer Front K . STEP-4 M LR 4 N 5 K LL 1. Align Drawer Back M with Drawer Bottom N and press firmly into slot . 2. Attach Drawer Back using two Allen Key Screws 4 through drilled holes on each Side LL , LR . 3. Use Allen Key 5 to tighten screws. Do not over-tighten. 4. Repeat Step 1-4 for the two other drawers.
ASSEMBLY MODEL # AXCLRY-10GW STEP-5 11 11 DL & DR Fro n t/A DL /A ont Fr van t van t DR Fro nt / Ava nt 1. Insert two Dowels 11 into drilled holes on each Left Divider DL and Right Divider DR . 2. Use rubber mallet to tap Dowels 11 into bottom of holes securely. 1/2 length of Dowels should be exposed.
ASSEMBLY MODEL # AXCLRY-10GW STEP-6 4 DR 5 E E DL 4 E E 5 Front / Avant Front / Avant DR Front / Avant Front / Avant 1. Attach Middle Frame E to Right Divider DR and Left Divider DL using twelve Allen Key Screws 4 ( six Screws / each Divider ). 2. Use Allen Key 5 to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCLRY-10GW STEP-7 11 11 t/ Fron nt Ava B 11 BOTTOM VIEW t Fron ant / Av TOP VIEW 1. Insert four Dowels 11 into drilled holes on Bottom Shelf B . 2. Use rubber mallet to tap Dowels 11 into bottom of holes securely. 1/2 length of Dowels should be exposed.
ASSEMBLY MODEL # AXCLRY-10GW STEP-8 Front / Avant Front / Avant Front / Avant DL DR B Front / Avant Front / Avant Front / Avant DL DR Front / Avant B 4 5 1. Attach Right Divider DR and Left Divider DL to Bottom Shelf B using six Allen Key Screws 4 . 2. Use Allen Key 5 to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCLRY-10GW STEP-9 11 11 ant F / Av t n o r CL & CR Ava ont / Fron t / Av CL CR nt Fr ant 1. Insert two Dowels 11 into drilled holes on each Left Side CL and Right Side CR . 2. Use rubber mallet to tap Dowels 11 into bottom of holes securely. 1/2 length of Dowels should be exposed.
ASSEMBLY MODEL # AXCLRY-10GW STEP-10 Front / Avant Front / Avant Front / Avant CL CL Front / Avant Front / Avant B 4 B 5 1. Attach Bottom Shelf B to Left Side CL using three Allen Key Screws 4 . 2. Use Allen Key 5 to tighten screws. Do not over-tighten.
Front / Avant Front / Avant Front / Avant Front / Avant Front / Avant Front / Avant Front / Avant Front / Avant ASSEMBLY MODEL # AXCLRY-10GW STEP-11 CR 4 B 5 CR B 1. Repeat Step-10 for Right Side CR .
ASSEMBLY MODEL # AXCLRY-10GW STEP-12 4 5 4 DL CR DR Front / Avant Front / Avant Front / Avant A Front / Avant 5 CL 1. Attach Top A to Sides CL , CR using six Allen Key Screws 4 ( three Screws / each Side ). 2. Attach Top A to Dividers DL , DR using six Allen Key Screws 4 ( three Screws / each Side ). 3. Use Allen Key 5 to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCLRY-10GW STEP-13 P 5 X 1 2 3 O O B B O O 1. Attach Legs O to Bottom Shelf B . 2. Use twelve Allen Key Bolts 1 , twelve Lock Washers 2 and twelve Washers 3 to secure part O and B (six Blots, six Lock Washers and six Washers on each Leg). 3. Use Allen Key 5 to tighten Bolts. Do not over-tighten.
ASSEMBLY MODEL # AXCLRY-10GW Warning Label STEP-14 Front / Front / NOTE: The screwdriver is not included in the hardware pack. Avant H Avant 6 J Front / I Avant H Front / A vant I J I 1. Attach the Top Back Panel H to back frame by using Phillips Screws 6 . Only 1st top row of screws ( six screws ) to be screwed in advance. 2. Insert the Bottom Back Panel I into the slot of Plastic Joining Strip J . 3.
ASSEMBLY MODEL # AXCLRY-10GW STEP-15 FL 10 12 FR 1. Attach Adjustable Hinges 12 to Doors FL , FR using Phillips Screws 10 into guide holes on Doors FL , FR .
ASSEMBLY MODEL # AXCLRY-10GW STEP-16 7 9 9 7 CR DR CL FR DL FL 12 10 CL DL CR FL DR FR 1. Attach Adjustable Hinges 12 on Doors FL , FR to Sides CL , CR using Phillips Screws 10 into guide holes on Sides CL , CR . 2. Attach Magnets 7 using Phillips Screws 9 into guide holes on Left Divider DL and Right Divider DR . 3. Use Phillips screwdriver to snugly tighten screw.
ASSEMBLY MODEL # AXCLRY-10GW IMPORTANT NOTE: 10 II I Tighten the Screw marked II to fasten hinge. The door may need to be adjusted so that all the spaces between the door and the unit sides are equal. To adjust, follow instructions: 1. Side adjustment 4 mm To move the door towards the side panel, loosen screw I and tighten screw II . To move the door away from the side panel, loosen screw II and tighten screw I . 2.
ASSEMBLY MODEL # AXCLRY-10GW STEP-17 shelf level 1 shelf support anti - tipping 8 shelf level 2 shelf level 3 8 G G G 1. Use four Shelf Supports 8 for each Shelf G in desired location . 2. Two Shelf Supports 8 may be used on back top of each Shelf G as a tipping restraint.
ASSEMBLY MODEL # AXCLRY-10GW STEP-18 P X 1. Insert assembled drawers into glides on assembled sideboard.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP-19 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. x P 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. P Drill a 3/16 inch hole in the wall.
TM SIMP HOME ® LIFE BY DESIG N TM WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line at 1-866-518-0120 ext.
