Safety Instructions & Operator’s Manual for SINGLE STAGE SNOW THROWER SERIES 0 Model 3190M 3190E Mfg. No. 1694382 1694383 MODEL NUMBER EXPLANATION 3 19 0 ENGINE HP AUGER WIDTH 3 – 3.0 HP (Engine Horse Power) E ENGINE OPTIONS SERIES DESIGNATION 19 – 19” Auger Width 0 -- Series Designation E – 110 Volt Electric Start M – Manual, Recoil Start Before operating your Snow Thrower, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following instructions may result in serious injury to the operator or other persons. The owner of the snow thrower must understand these instructions and, furthermore, must allow only persons who understand these instructions to operate snow thrower.
IMPORTANT SAFETY INSTRUCTIONS 5. DO NOT store the machine or fuel container inside where there is an open flame, spark or pilot light such as on a water heater or other appliances. 6. DO NOT fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place the containers on the ground away from the vehicle before filling. 7. Remove gas-powered equipment from the vehicle or trailer and refuel it on the ground.
TABLE OF CONTENTS SECTION 1 - IMPORTANT SAFETY INSTRUCTIONS.......................... 2-3 TABLE OF CONTENTS ............................................................................ 4 SECTION 2 - OPERATING INSTRUCTIONS......................................... 5-9 Pre-start Checklist ........................................................................................... 5-6 Starting & Stopping Engine (Recoil Start Models) ........................................
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check guards, chutes, deflectors and covers to make sure all are in place and securely tightened. 2.1.2. Check auger control to insure it works freely. See Figure 2.1. STANDARD FLUID MEASUREMENT (32:1 Ratio) GASOLINE (Gallons) 0.25 0.50 0.75 1.00 1.25 1.50 2.00 AUGER CONTROL 2 CYCLE OIL (Ounces) 1.00 2.00 3.00 4.00 5.00 6.00 8.
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST (Continued from Previous Page) Make the following checks and perform the service required before each start-up. WARNING DO NOT use an electrical extension cord that is damaged. A damaged electrical extension cord could cause a shock or fire. Thoroughly inspect electrical extension cord before using machine. If cord is damaged, do not use and do not operate machine. Replace damaged cord immediately.
Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING, STOPPING & OPERATION (RECOIL START MODELS) 2.2.1. ENGINE & AUGER 1. Move choke control to the choke “ON” position. See Figure 2.4. WARNING Release auger clutch control and make sure auger/impeller has STOPPED before rotating discharge chute or adjusting deflector. DO NOT place hands near auger/impeller while engine is running. NOTE: Stop the auger by releasing the auger control. Stop the engine by turning the key switch to the “OFF” position.
Section 2 - OPERATING INSTRUCTIONS 1. Connect the power cord to the starter switch box on machine’s control panel then plug the other end into 120 volt AC receptacle. 2. Turn ignition key to the “ON” position. 3. Move choke control to the choke “ON” position. See Figure 2.8. 4. Push primer button three times to start a cold engine. NOTE: Do not use primer button to start warm engine. 5. Push the electric starter button. DO NOT hold button for more than 20 seconds to avoid damaging the starting motor.
Section 2 - OPERATING INSTRUCTIONS WARNING Objects can be thrown by the snow thrower while it is in operation. Thrown objects could cause serious injury to the operator or bystanders. Always wear safety goggles or other suitable eye protection. Keep people and pets away from area. 2.2.6. ENGAGING AUGER 1. Pull auger control against handle to engage auger. See Figure 2.5. WARNING Release auger clutch control and make sure auger/impeller has STOPPED before rotating discharge chute or adjusting deflector.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the snow thrower, use only factory authorized replacement parts. Contact a local authorized dealer for parts and service assistance. For the correct part or other information for a particular snow thrower, always mention the Model, Manufacturer Number and Serial Number. 3.2.3 CHECK AUGER CLUTCH CONTROL CABLE 1. Visually check cable for fraying, kinking or severed cable strands. Replace cable and adjust tension before operating snow thrower.
Section 4 - REPAIR & ADJUSTMENTS 4.1.2. AUGER BELT IDLER PULLEY ADJUSTMENT NOTE: To adjust the idler pulley and properly tension the auger belt, the auger control cable adjustment must first be loosened as described in the following step. Cable adjustment must be checked after completing the idler pulley adjustment. WARNING DO NOT attempt any adjustments, maintenance, service, or repairs with engine running. Stop auger. Stop engine. Remove key. Remove spark plug wire and secure wire away from spark plug.
Section 4 - REPAIR & ADJUSTMENTS 4. Push the spring tensioned idler pulley down and install new belt. See Figure 4.5. WARNING DO NOT attempt any adjustments, maintenance, service, or repairs with engine running. Stop auger. Stop engine. Remove key. Remove spark plug wire and secure wire away from spark plug. BELT COVER RETAINING STUDS SHOWN REMOVED 4.1.2. AUGER BELT IDLER PULLEY ADJUSTMENT (Continued From Previous Page) 3. Loosen nut and bolt that secures the idler pulley to idler arm.
Section 4 - REPAIR & ADJUSTMENTS WARNING AUGER DO NOT attempt any adjustments, maintenance, service, or repairs with engine running. Stop auger. Stop engine. Remove key. Remove spark plug wire and secure wire away from spark plug. FLITE SHOE 4.1.3. AUGER BELT REPLACEMENT (Continued From Previous Page) 5. Reinstall belt guide. IMPORTANT: Make sure when reinstalling belt guide that it does not touch drive pulley. Belt guide should an equal amount of clearance on both belt guide fingers. See Figure 4.6. 6.
TROUBLESHOOTING PROBLEM PROBABLE CAUSE Engine Will Not Start Using Recoil Starter CORRECTIVE ACTION 1. Fuel tank empty. 2. Engine needs choking & priming. Engine Will Not Crank 1. Power extension cord not plugged into machine or Using Electric Starter 110 Volt outlet. 2. Power extension cord damaged. 3. Starter switch damaged or faulty. 4. Key switch turned to “OFF” position. 1. Fill fuel tank with fresh fuel/oil mix. 2. Move choke control to “CHOKE” position. Push primer bulb three times. 3.
2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
Safety Instructions & Operator’s Manual for SINGLE STAGE SNOW THROWER SERIES 0 IMPORTANT These products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments.
